NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 3 40
Revision 2.0
PRIVACY/PRIVACY RELEASE
PROGRAMMING
 
DESCRIPTION DATA
Assign the Class of Service for Privacy Re-
lease to the required stations. •  CM12YY = 02
(1)  X-XXXX: Primary Extension No. 
(2) XXXX
*a: Service Rest. Class B (00-15 ) 
•  CM15 YY = 63 
(1)  00-15 (Service Rest. Class B assigned by 
CM12 YY = 02) 
(2) 1 : Allowed
START
END
CM12
CM15*a 
						

							ND-45670 (E) CHAPTER 2
Page 341
Revision 2.0
PRIVATE LINES
PROGRAMMING 
When providing Private Lines for a single line or Multiline Terminal, do the following TRUNK-DIRECT APPEAR-
ANCES programming.
DESCRIPTION DATA
Assign the trunks to be seized on a per-station 
basis.•  YY = 16
(1)  X-XXXX: Station number
(2) D000-D255: Trunk number 
Specify the designated seizure of trunks on a 
per-trunk route basis.•  YY = 98
(1)  Trunk route number (00-63) 
(2)  0/1 : Private Lines/No Private Lines
 
Specify the number of times to hunt through 
the trunks within the trunk route.(1) 08
(2) 01-16: One time-16 times 
If data is not set, the default setting (none) is 
00 (no seizure when the designated trunk is 
busy). To assign default setting, assign “ccc”. 
START
END
CM12
CM35
CM42 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 42
Revision 2.0
PROPRIETARY MULTILINE TERMINAL
PROGRAMMING 
DESCRIPTION DATA
Assign the Multiline Terminal Number to the 
associated LEN. 
Note:When PN-4DLC card is accommodat-
ed, the Multiline Terminal Number
must be assigned for the all lines (4
lines) of the card.(1) 0000-0511 (LEN No.) 
(2)  FX-FXXXX: Multiline Terminal No.X-
XXXX represents Primary Exten-
sion No.
Assign the Class of Service for the accommo-
dation of Single Line Telephone to Multiline 
Terminal, if required (Assignment for Single 
Line Telephone only).• YY = 05
(1)  X-XXXX: Station No. 
(2) 0: Accommodated 
Assign the station numbers, trunk numbers or 
service feature access keys on each Multiline 
Terminal, if required. 
Assign the Dedicated Feature Keys as follows. 
No data setting is required for the     keys.• YY = 00
(1)  Primary Extension No. +   + Key No. 
(01-16) 
(2)  Refer to Command Manual (CM90)
• YY = 00 
(1)  Primary Extension No. +   + Key No. 
(17-24) 
(2)  See left table
Specify whether call termination is indicated 
on the Call Indicator Lamp or not on each line 
key. • YY = 05
(1)  Primary Extension No.+   + Key No. 
(01-16) 
(2)  0: Not to be indicated 
1 : To be indicated
CM10 START
CM12
CM90
A
Key No.
2nd Data
17
18
19
20
21
22
23
24F1015 (RECALL)
F1011 (FNC)
F1012 (CNF)
F1000 (LNR/SPD)
F1016 (SPKR)
F4000 (ANS)
F1004 (TRF)
F1010 (HOLD)
,
,
, 
						

							ND-45670 (E) CHAPTER 2
Page 343
Revision 2.0
PROPRIETARY MULTILINE TERMINAL
DESCRIPTION DATA
Assign the Outgoing Call Preset/Answer Pre-
set functions to Multiline Terminal, if re-
quired.(1) 145
(2)  0: To be provided
1 : Not to be provided
Assign whether the answer key rings on TAS 
and Pooled Line or not.(1) 116
(2)  0: Available
1 : Not Available
Specify the Delayed Ringing timing. •  Y = 1
(1) 09
(2)  01-20: 2-40 sec. in 2 sec. increments 
If no data is set, the default setting is 10 sec-
onds.
Provide Trunk-Direct Appearances to the 
trunk number. •  YY = 18
(1)  Trunk No. (000-255) 
(2)  0: To be provided.
END
CM08
A
CM30
CM41 
						

							CHAPTER 2 ND-45670 (E)
Page 344 Addendum-001
Revision 2.1 JULY, 1998
PROPRIETARY MULTILINE TERMINAL
To provide the key number 30 through 37 of Multiline Terminal (ETJ-24DS-1/DTP-32-1/DTP-32D-1), do the fol-
lowing programming.
DESCRIPTION DATA
Assign the dummy terminal number (Add-
On-Module number) for the key number 30 
through 37. 
Note:When the data assignment of both
Add-On Module and DSS Console
are required, do not use the same
number (the last two digits of the da-
ta).(1) 0000-0511 (LEN No.) 
(2) EC00-EC31: Add-On Module No.
For PIM0/1: EC00-EC07 
For PIM2/3: EC08-EC15 
For PIM4/5: EC16-EC23 
For PIM6/7: EC24-EC31 
Note:EC00-EC31 may be assigned in any
PIM for 1900 series software.
Assign the Multiline Terminal associated with 
the dummy terminal (Add-On Module). 
Note:This data must be assigned before
the data assignment of CM90. •Y=0
(1) 00-31: Add-On Module No. (Last two 
digits of EC00-EC31 assigned by CM10) 
(2) X-XXXX: Primary Extension No.
Assign station numbers, trunk numbers, or 
service feature access keys to key numbers 30 
through 37.• YY=00 
(1) Primary Extension No. +   + Add-On
Module Key No. (30-37) 
(2) Refer to Command Manual (CM90) 
Specify whether to indicate call termination 
on the Call Indicator Lamp or on each line 
key. • YY=05
(1) Primary Extension No. +   + key No.
(30-37) 
(2) 0 : Not indicated 
1 : Indicated
START
END
CM10
CM98
CM90,
, 
						

							ND-45670 (E) CHAPTER 2
Page 345
Revision 2.0
PROPRIETARY MULTILINE TERMINAL
To select the language indicated on the LCD of the Multiline Terminal, set the following data.
To Accommodate the Series E Multiline Terminal with Series III mode or to accommodate the Elite Terminal, do
the following programming.
HARDWARE REQUIRED 
Multiline Terminal and DLC card
DESCRIPTION DATA
Select language to display on LCD. • YY = 00
(1) 00
(2) 1 : English
2 : French
7 :  Depends on nation code
DESCRIPTION DATA
Specify the type of Multiline Terminal accom-
modated in each DLC card.
Note 1:For PN-4DLCD or 4DLCA cards,
assign this data to the first LEN (Lev-
el 0) of each 4 posts DLC card. For
PN-8DLCD cards, assign this data
to first (Level 0) and fifth (Level 4)
LENS of each 8 post card.
Note 2:For 4-wire type DLC card (2DLCC,
4DLCF), this data is not required.
Note 3:The same type of Multiline Terminals
must be accommodated in the same
DLC card. For detail conditions, re-
fer to the CM12 YY = 17 in the Com-
mand Manual.• YY = 17
(1) XXXX: Primary Extension No.
(2) 0 : Series E (Series III mode)
1 : Elite
3 :  Series E (Series E mode),
Series III, E-pro
START
END
CM04
START
END
CM12
INITIAL 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 46
Revision 2.0
PROPRIETARY MULTILINE TERMINAL: AUTOMATIC IDLE RETURN
PROGRAMMING
HARDWARE REQUIRED 
Multiline Terminal and DLC card
DESCRIPTION DATA
Provide the system with this feature.  (1) 172 
(2) 1 : Available
START
END
CM08 
						

							ND-45670 (E) CHAPTER 2
Page 347
Revision 2.0
PROPRIETARY MULTILINE TERMINAL: CALLING NAME AND NUMBER
PROGRAMMING 
HARDWARE REQUIRED 
Multiline Terminal and DLC card
DESCRIPTION DATA
Specify station number and name display 
when an incoming call begins ringing.(1) 335 
(2) 0 : Station number and name display 
only when incoming call termi-
nates to prime line.
1 : Station number and name display 
when incoming call terminates to 
prime line or primary extension.
START
END
CM08 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 48
Revision 2.0
PROPRIETARY MULTILINE TERMINAL: DIGITAL SINGLE LINE
PROGRAMMING
HARDWARE REQUIRED 
Multiline Terminal and DLC card
DESCRIPTION DATA
YY = 07:Service Restriction Class C
(1) Station X-XXXX
(2) Restriction Class 00-15
Disable Dial Tone Activation when pressing 
One-Touch Spd. key while terminal is idle.YY = 87:One-Touch activates DT when Termi-
nal Idle
(1)Station Class C
(2) 0 : Remain Idle
1  : Off Hook and Dial Tone
Assign and delete feature keys.
Note:Use Key Number 20 for Redial key. Use
Key Number 23 for Flash key.
Prime line should be assigned to Key 9.
Digital Single Line is a D
term and can use any 
key assigned in CM90. However, the Digital 
Single Line Terminal has no LEDs, speaker, 
or microphone. Assign any features that can 
be used without these devices.YY = 00:Key Data
(1) X-XXXX: Primary Extension No. +   + 
Key #.
(2) F1100 - F1199: Station Speed Dial
F1012:  Conference key
This key is required to program 
speed dial keys.
F0069: Last number redial (Key #20)
F1004:   Transfer key (Key #23)
Assign prime line to primary extension. (1) Primary Extension #: X-XXXX
(2) Prime Line: X-XXXX
CM12
CM15 START
CM93
CM90,
CNF
TRF 
						

							ND-45670 (E) CHAPTER 2
Addendum-001 Page 348-1
JULY, 1998 Revision 2.1
PROPRIETARY MULTILINE TERMINAL: DYNAMIC DIAL PAD
(1900 Series Enhancement)
PROGRAMMING 
Do the following programming to make an outgoing call. Press any key on the dial pad of a Multiline Terminal, with-
out pressing a Speaker key or going off hook.
DESCRIPTION DATA
Assign a Prime line to the Multiline Terminal. (1) X-XXXX: Primary Extension No. 
(2) X-XXXX: Station No. 
Assign Service Restriction Class A to each 
station.• YY=02
(1) X-XXXX: Station No.
(2) XX: Service Restriction Class A 
(00-15 )
Assign this service to Service Restriction 
Class A assigned by CM12 YY=02.• YYY=120
(1) 00-15: Service Restriction Class A
(2) 0: Allowed
START
END
CM12
CM93
CM15