NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 1 24
Revision 2.0
CALLER ID CLASS (1500 Series Enhancement)
DESCRIPTION DATA
Specify the ringing tone for each calling 
number, if required.•
(1)
(2)YY=04 (Ringing Tone Assignment)
Development Table No.0-1499
0 : Depends on CM35 YY=33
1: Not used
2: Internal Ringing Tone
3: External Ringing Tone
Specify which is displayed on the LCD, when 
receiving both the calling number and the 
name from network on incoming call.•
(1)
(2)YY=05 (Calling Number/Name Display) 
Development Table No.0-1499
0 : Calling Number Display 
1: Calling Name Display
Specify whether the Call Waiting is set for 
each calling number or not.•
(1)
(2)YY=06 (Call Waiting) 
Development Table No.0-1499
0 : Not available
1: Available
Specify whether the UCD Priority Queuing is 
set for each calling number or not.•
(1)
(2)YY=07 (UCD Priority Queuing)
Development Table No.0-1499
0 : Not Priority
1: Priority
Specify the priority for calling name display. •
(1)
(2)YY=12 (Priority for Name Display) 
Development Table No.0-1499
0 : Name received from the network is 
displayed.
1: Name assigned by CMDB YY=00 is 
displayed.
Specify the type of Single Data Message 
Frame Format.•
(1)
(2)YY=30
1 (Single Data Message Frame Format)
0 : with Time Parameter
1: without Time ParameterCMDB
END
A 
						

							ND-45670 (E) CHAPTER 2
Page 125
Revision 2.0
CALLER ID CLASS (1500 Series Enhancement)
5. Other Relational Data Assignment
DESCRIPTION DATA
Assign the Trunk Access Code for outgoing 
call sent to the SMDR.
For using Save & Repeat feature, this Trunk 
Access Code will save and sent with the 
calling number.•
(1)
(2)YY=44
(Trunk Access Code for Save &Repeat) 
Trunk Route No. (00-63) 
X/XX : Trunk Access Code 0-9/00-99 
Specify whether the calling number is sent to 
the OAI Terminal or not.(1)
(2)462 (Sending to OAI Terminal) 
0: To be sent 
1 : Not to be sent
Specify whether the calling number is sent to 
the SMDR Terminal or not.(1)
(2)463 (Sending to SMDR Terminal) 
0: To be sent 
1 : Not to be sent
Send ANI/Caller ID to SMDR.
Note:This is reuired when using PN-AP00
for SMDR.(1)
(2)143 (Sending to SMDR Terminal)
0 : Not to be sent 
1: To be sent
Provide the Multiline Terminal with a Display 
Change key for calling number/name display 
changing.•
(1)
(2)YY=00
Primary Extension No.+ +Key No.
F1099 : Calling No./Name Display 
Provide the ATTCON with a Display Change 
key for calling number/name display 
changing.•
(1)
(2)YY=00
ATTCON No.+ +Key No.
F6122 : Calling No./Name Display 
CM35
CM08
CM90 START
END
CM
D000
,
, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 26
Revision 2.0
CALLER ID CLASS (1500 Series Enhancement)
6. Data Assignment for multiple CIR Trunk
The development data by CMDC and CMDB are assigned toward the first CIR Trunk which has been as-
signed a minimum Slot Number. When providing multiple CIR Trunks, save the development data and load
them for the other CIR Trunks according to the following steps.
For detail of MAT operations, refer to the MAT Operation Guide.
STEP 1 After assignment of CMDC and CMDB, save the office data by MAT.
At this time, specify the AREA Number including the MEMORY ADDRESS 00900-2FFFF.
STEP 2 Set the MB switch to ON (UP) on the first 
CIR Trunk with minimum Slot Number X.
Slot Number X
< Y< Z< W
STEP 3 As for the second CIR Trunk, change the Slot Number Y to X 
by CM05 and by the SENSE switch.
STEP 4 Set the SW1-1 through SW1-4 to ON on the second CIR Trunk.
Clear the memory for CMDC and CMDB by CMDB YY=90.
Set the SW1-1 through SW1-4 to OFF on the second 
CIR Trunk.
STEP 5 Load the office data saved in STEP1 by MAT.
STEP 6 As for the second CIR Trunk, restore the Slot Number X to Y 
by CM05 and by the SENSE switch.
Jump to STEP17 if no more CIR Trunks are provided.
STEP 7 Set the MB switch to ON (UP) on the second 
CIR Trunk with Slot Number Y.
STEP 8 As for the third CIR Trunk, change the Slot Number Z to X 
by CM05 and by the SENSE switch.
STEP 9 Set the SW1-1 through SW1-4 to ON on the third CIR Trunk.
Clear the memory for CMDC and CMDB by CMDB YY=90.
Set the SW1-1 through SW1-4 to OFF on the 
third CIR Trunk.
STEP 10 Load the office data saved in STEP1 by MAT.
STEP 11 As for the third CIR Trunk, restore the Slot Number X to Z 
by CM05 and by the SENSE switch.
Jump to STEP17 if no more CIR Trunks are provided. 
						

							ND-45670 (E) CHAPTER 2
Page 127
Revision 2.0
CALLER ID CLASS (1500 Series Enhancement)
STEP 12 Set the MB switch to ON (UP) on the third CIR Trunk with Slot Number Z.
STEP 13 As for the fourth CIR Trunk, change the Slot Number W to X 
by CM05 and by the SENSE switch.
STEP 14 Set the SW1-1 through SW1-4 to ON on the fourth CIR Trunk.
Clear the memory for CMDC and CMDB by CMDB YY=90.
Set the SW1-1 through SW1-4 to OFF on the 
fourth CIR Trunk.
STEP 15 Load the office data saved in STEP1 by MAT.
STEP 16 As for the fourth CIR Trunk, restore the Slot Number X to W 
by CM05 and by the SENSE switch.
STEP 17 Set the MB switches to OFF (DOWN) on all the CIR Trunks.
HARDWARE REQUIRED
PN-4COTG card
PN-4RSTC card 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 28
Revision 2.0
CALLER ID DISPLAY
(1800 Series Enhancement)
PROGRAMMING
In addition to Automatic Number Identification (ANI) or Caller ID Class, assign the following data.
DESCRIPTION DATA
Provide the Multiline Terminal with a Caller 
ID Display key for displaying the ANI or 
Caller ID.•
(1)
(2)YY=00
Primary Extension No. +   + Key No.
F5010: Caller ID Display
START
END
CM90
, 
						

							ND-45670 (E) CHAPTER 2
Page 129
Revision 2.0
CALL FORWARDING: CALL FORWARDING - ALL CALLS
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for this feature to
the required stations.
Note:When providing Call Forwarding-All
Calls-Outside, set “1” (Allowed) for
YY = 00, YY = 26 of CM15.•
•
•
(1)
(2)CM12 YY=02
[Service Restriction Class (A) (00-15 )]
CM15 YY=00 (Call Forwarding-All
Calls)
CM15 YY=26 (Call Forwarding-All
Calls-Outside)
XX: Service Restriction Class (A) 
assigned by CM12 YY=02.
1 : Allowed
Assign the access code for Call Forwarding-
All Calls, Entry and Cancel, respectively.•
(1)
(2)Y = 0-3 (Numbering Plan Group 0-3)
X-XXX: Access Code (*5, #5)
010: Entry
011: Cancel
To apply this feature to incoming calls, set the
trunk route combinations for Tandem Connec-
tion.
Note:For Resident System Programming, 
refer to the Command Manual.•
(1)
(2)
•
(1)
(2)CM35 YY=05
Trunk Route No. (00 - 63)
Note
1 : Release Signal arriveNote
CM36
Incoming Trunk Route No. + Outgoing
Trunk Route No. (Assigned by CM35 
YY=05)
0: Allowed
CM12
CM15
CM20
CM35
CM36
A START
t
tt 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 30
Revision 2.0
CALL FORWARDING: CALL FORWARDING - ALL CALLS
DESCRIPTION DATA
Specify the setting method for Call Forward-
ing-All Calls-Outside.(1)
(2)222
0: The feature is set when the station
goes on hook/when receiving Ser-
vice Set Tone (ORT time out)
1 : The feature is set when receiving
Service Set Tone (ORT time out)
Assign whether or not an extention can set
Call Forwarding-All Calls-Outside by enter-
ing only a trunk access code.(1)
(2)386
0: Restrict
1 : Allow
Assign whether or not the system should
check the trunk restriction class of the for-
warded 
station during a Call Forwarding-All Calls-
Outside.(1)
(2)387
0:  Call forwarding All Calls-Outside
follows setting station class
1 : No check
Assign Call Forwarding-All Calls keys to the
Multiline Terminals, as required.•
(1)
(2)YY=00
Primary Extension No. +   + Key No.
F0010:  Call Forwarding-All Calls Set/
Cancel
Provide Call Forwarding feature to each 
tenant as per incoming call type.•
•
•
(1)
(2)YY=23 (Internal Call or ATT-assisted
Call)
YY=24 (C.O. Incoming Call)
YY=25 (Tie Line Incoming Call)
Tenant No. (00-63)
1 : Call Forwarding
Select the Dial Tone on Setting Call Forward-
ing-All Calls. (1300 Series Enhancement)•
(1)
(2)Y=2
13 (Dial Tone on Setting Call Forward-
ing-All Calls)
0: Special Dial Tone (Stutter Dial
Tone)
1 : Dial ToneCM08
CM90
CM65
CM48
A
END
ttt
,
t
INITIAL
t 
						

							ND-45670 (E) CHAPTER 2
Page 131
Revision 2.0
CALL FORWARDING: CALL FORWARDING-BUSY LINE
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for this feature to 
the required stations.
Note:When providing Call Forwarding-
Busy Line-Outside, set “1”
(Allowed) for YY = 11, YY = 28, YY
= 12, YY= 29 of CM15.•  CM12 YY = 02
[Service Restriction Class (A) (00-
15 )]
•  CM15YY = 11 (Call Forwarding-Busy 
Line)
•  CM15YY = 28 (Call Forwarding-Busy 
Line-Outside)
• CM15YY=12 (Call Forwarding-Busy 
Line/-No Answer)
• CM15YY=29 (Call Forwarding-Busy 
Line-Outside/-No Answer-Outside)
(1)  XX: Service Restriction Class (A) 
assigned by CM12 YY = 02.
(2)  1 : Allowed
Assign the access code for Call Forwarding-
Busy Line, Entry and Cancel, respectively.•  Y = 0-3 (Numbering Plan Group 0-3)
(1)  X-XXX: Access Code (*6, #6)
(2) 014: Entry
015: Cancel
For setting the same access code as Call For-
warding-No Answer
(2) 012: Entry
013: Cancel
To apply this feature to incoming calls, set the 
trunk route combinations for Tandem 
Connection.
Note:For Resident System Programming,
refer to the Command Manual.• CM35YY = 05
(1)  Trunk Route No. (00 - 63) 
Note
(2)  1 : Release Signal arrive Note
• CM36
(1)  Incoming Trunk Route No. + Outgoing 
Trunk Route No. (Assigned by CM35 YY 
= 05)
(2) 0: Allowed
START
CM20
CM12
CM15
CM35
CM36
A 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 32
Revision 2.0
CALL FORWARDING: CALL FORWARDING-BUSY LINE
DESCRIPTION DATA
Specify the setting method for Call 
Forwarding-Busy Line-Outside.(1) 222
(2) 0: The feature is set when the station goes 
on hook/when receiving Service Set 
Tone (ORT time out)
1 : The feature is set when receiving 
Service Set Tone (ORT time out)
Allow or restrict the ability to set Call 
Forwarding-Busy Line for a station with Do 
Not Disturb set.(1) 240
(2) 0: Allow
1 : Restrict
Assign whether or not an extension can set 
Call Forwarding-Busy Line-Outside by 
entering only a trunk access code.(1) 386
(2) 0: Restrict
1 : Allow
Assign whether or not the system should 
check the trunk restriction class of the 
forwarded station during a Call Forwarding- 
Busy Line Outside.(1) 387
(2) 0: Call Forwarding-Busy Line-Outside 
follows setting station class
1 : No check
Assign Call Forwarding-Busy Line keys to the 
Multiline Terminals, as required.• YY=00
(1) Primary Extension No. + + Key No.
(2) F0014: Call Forwarding-Busy Line Set/
Cancel
For setting the same key as Call Forwarding-
No Answer
(2) F0012: Set/Cancel
Provide Call Forwarding feature with each 
tenant as per incoming call type.• YY=23 (Internal Call or ATT assisted 
Call)
• YY=24 (C.O. Incoming Call)
• YY=25 (Tie Line Incoming Call)
(1) Tenant No. (00-63)
(2) 1 : Call Forwarding
CM90
A
END
CM65
CM08
, 
						

							ND-45670 (E) CHAPTER 2
Page 133
Revision 2.0
CALL FORWARDING: CALL FORWARDING-NO ANSWER
PROGRAMMING
DESCRIPTION DATA
Assign the Class of Service for this feature to 
the required stations.
Note:When providing Call Forwarding-No
Answer-Outside, set “1” (Allowed)
for YY=10, YY=27, YY=12, YY=29
of CM15• CM12YY = 02
[Service Restriction Class (A) (00-
15 )]
• CM15YY=10 (Call Forwarding-No An-
swer)
• CM15YY=27 (Call Forwarding-No An-
swer-Outside)
• CM15YY=12 (Call Forwarding-Busy 
Line/-No Answer)
• CM15YY=29 (Call Forwarding-Busy 
Line-Outside/-No Answer-Outside)
(1) XX: Service Restriction Class (A) as-
signed by CM12 YY=02.
(2) 1 : Allowed
Assign the access code for Call Forwarding-
No Answer, Entry and Cancel. respectively.• Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code (*6, #6)
(2) 016: Entry
017: Cancel
For setting the same access code as Call 
Forwarding-Busy Line
(1) 012: Entry
013: Cancel
Specify the timing for Call Forwarding-No 
Answer for a trunk incoming call.•Y = 0
(1) 01
(2) 01-30 :4-120 sec. in 4 sec. increments
If no data is set, the default setting is 32-36 
seconds.
Specify the timing for Call Forwarding-No 
Answer for an internal call or an assisted call.•Y = 0 
(1) 15
(2) 01-30: 4-120 sec. in 4 sec. increments
If no data is set, the default setting is 32-36 
seconds.
START
CM41
CM20
A
CM12
CM15