NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 1 94
Revision 2.0
DIRECT INWARD DIALING (DID)
DESCRIPTION DATA
Assign the data for DID to the Trunk Routes 
assigned by CM30. • YY = 00 (Kind of Trunk)
(1) Trunk Route No. (00-63)(03)
(2) 00: DID 
• YY = 02 (OG/IC)
(1) Trunk Route No. (00-63)(03) 
(2) 1: Incoming
• YY = 05 (Release Signal Condition) 
(1) Trunk Route No. (00-63)
(2) 0: No Release Signal
• YY = 12 (Number of digits to be re-
ceived)
(1) Trunk Route No. (00-63) 
(2) Number of digits 
0 : 1 digit
1 : 2 digits 
2 : 3 digits 
3: 4 digits 
• YY = 18 (Received Digit Conversion)
(1) Trunk Route No. (00-63)
(2) 0/1: To be provided/Not to be pro-
vided.
Provide dedicated DTMF Receivers for DID 
Calls, if required.•Y = 1
(1) XX
 X: DTMF Receiver No.
*a : Card No. (00-15) assigned by 
CM10. (E200-E215) 
*b : Circuit No. (0-3)
(2)  0/1: Only for DID/For both DTMF 
station and Tie Line/DID
B
A
CM35
CM45
*b *a 
						

							ND-45670 (E) CHAPTER 2
Page 195
Revision 2.0
DIRECT INWARD DIALING (DID)
DESCRIPTION DATA
Assign the function of each Digital 
Announcement Trunk, if needed.• YY = 00
(1) 000-127: Digital Announcement 
Trunk Circuit No. 
(2) 0DD0: Announcement Service 
when the called station does 
not answer the DID/Tie Line 
call
0800: Announcement Service 
when the DID/Tie Line call 
terminates to the Busy sta-
tion. 
Automatic Transfer Destinations:
For the DID line, the destination to which an 
incoming call transfers when the station does 
not answer the call within a predetermined 
time.• YY = 00
(1) XX : Group No. 
(2) EB000-EB127 : Digital Announce-
ment Trunk Circuit 
No. 
C
B
CM49
CM51 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 96
Revision 2.0
DIRECT INWARD DIALING (DID)
HARDWARE REQUIRED 
PN-AUCA card ´ n 
DESCRIPTION DATA
When the data for CM35 YY = 18 is set to 
“0” (Received Digits Conversion is to be 
provided), assign the data for interpreting the 
digits received.• Y = 0 (Day Mode) 
• Y = 1 (Night Mode) 
(1) X-XXXX: Station Number received.
(2) X-XXXX: Station Number to be ter-
minated. 
DXX: Change Terminating System to:
D01:
D13: TAS 
D04: DIT 
D14: SN610 ATTCON
D16: DISA
D09: AUTO ATT.
END
CM76
C 
						

							ND-45670 (E) CHAPTER 2
Page 197
Revision 2.0
DIRECT INWARD DIALING (CALL WAITING)
DESCRIPTION DATA
Specify the Camp-On tone sent to a busy 
station by Camp-On Call Waiting Method.(1) 367 
(2) 0: Every 4 sec.
Only once
Assign the Class of Service for the Call 
Waiting feature to the required stations.• CM12, YY=02[Service Restriction 
Class (A) (00-15 )]
• CM15, YY=44 (Call Waiting Method 
Answer from called side)
(1) Service Restriction Class (A) (00-15) 
assigned by CM12, YY=02
(2) 1 : Allowed
Assign the data for DID Call Waiting to the 
Trunk Routes assigned by CM30
Specify the number of times for Call Waiting 
Tone.
Note:This data is effective when the 2nd data
of CM08-367 is “0”
• YY = 59 (Call Waiting for DID call) 
(1) Trunk No. (00-63) 
(2) 0: To be provided
(1) 18
(2) 01-99 (Number of Times)
If no data is set, the default setting is for no 
limitation.
Specify Call Waiting for DID call per 
incoming LDN number, if desired
Note:This data is effective when the 2nd data
of CM35, YY=18 is “0” (Received Dig-
its Conversion is to be provided).
•Y=5
(1) X-XXXX: Station Number received
0 : Restricted
1 : Allowed
CM08
END
START
CM12
CM15
CM35
CM42
CM76 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 98
Revision 2.0
DIRECT INWARD DIALING (CALL WAITING)
DESCRIPTION DATA
Assign DID incoming LDN display on 
Multiline Terminal.
Note:When 2nd Data is set to “1”, the Trunk
ID number assigned by CM30, YY=19
is displayed.
• YY=75 (DID incoming LDN display on 
Multiline Terminal)
(1) Trunk Route No. (00-63)
(2) 0 : Available
1 : Not Available - 
Note
END
START
CM35 
						

							ND-45670 (E) CHAPTER 2
Page 199
Revision 2.0
DIRECT INWARD SYSTEM ACCESS (DISA)
PROGRAMMING
To provide the DISA without Application Processor (PN-AP01):
DESCRIPTION DATA
Designate the processor for checking the ID 
code on DISA. (1) 217 
(2) 0: MP (PN-CP00) 
Assign the ring rate on a DISA call. (1) 180 
(2) 0/1: 0.2 sec. ON, 0.2 sec. OFF, 0.2 
sec. ON, 0.2 sec. OFF, 0.2 sec. 
ON, 0.2 sec. OFF/As per the data 
of CM35 YY = 33
Assign the data for DISA to the required 
trunks.• YY = 02 (Terminating System in Day 
Mode) 
• YY = 03 (Terminating System in Night 
Mode) 
(1) Trunk No. (000-255) 
(2) 16: DISA
• YY = 30 (Handling of DISA destination 
in Day mode) 
• YY = 31 (Handling of busy/not avail-
able DISA destination in Night 
mode)
(1) Trunk No. (000-255)
(2) 00 : C.O. Line Release 
01 : Forwarded to TAS
03 : Forwarded to ATTCON 
04 : Forwarded to DIT Station 
assigned by CM30 YY = 
04, 05.
06 : DT Connection for redial
08 : C.O. Line Release 
15:C.O. Line Release 
Assign the data for digit conversion on DID 
call to the Route No. assigned by CM30 YY 
= 00 when providing DISA to the DID call. • YY = 18
(1) Trunk Route No.(00-63)
(2) 0/1: To be provided/Not to be pro-
videdCM08
CM30
CM35 START
A 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 00
Revision 2.0
DIRECT INWARD SYSTEM ACCESS (DISA)
Note:Up to 8 DISA ID Codes can be set per system.
DESCRIPTION DATA
When the data for CM35 YY = 18 is set to 0, 
assign the data for converting the received 
digit(s) to DISA. • Y = 0 (Day Mode) 
• Y = 1 (Night Mode) 
(1) X-XXXX: Station No. received
(2) D16: DISA 
Assign the ID code for DISA. The maximum 
number of digits for an ID code is specified 
by CM42-13.•Y = 5
(1) XX : 00-07 (ID code serial 
number) 
(2) X-X...X : ID code (Max. 16 digits)
Assign the required Trunk Restriction Class 
to each ID code.•Y = 6
(1) XX : 00-07 (ID code serial 
number) 
(2) 1:Unrestricted (RCA)
2 : Non-Restricted-1 (RCB)
3 : Non-Restricted-2 (RCC)
4 : Semi-Restricted-1 (RCD) 
5 : Semi-Restricted-2 (RCE) 
6 : Restricted-1 (RCF)
7 : Restricted-2 (RCG)
8 : Fully-Restricted (RCH)
Assign the required Service Class A/B to 
each ID code. The features available in each 
class are assigned by CM15. •Y = 7
(1) XX: 00-07 (ID code serial number) 
(2) XX
 XX
*a: Service Feature Class (A) 
(00-15 ) 
*b: Service Feature Class (B) 
(00-15 ) 
Assign the required Service Class C to each 
ID code. The features available in each class 
are assigned by CM15. •Y = 8
(1) XX: 00-07 (ID code serial number) 
(2) XX: 00-15 (Service Restriction 
Class (C)) 
Specify the maximum number of digits for 
ID Codes on DISA.(1) 13
(2) 01-16 (Number of digits)
If no data is set, 10 digits of ID Code is 
available. 
CM76
CM2A
CM42
A
END
*b *a 
						

							ND-45670 (E) CHAPTER 2
Page 201
Revision 2.0
DIRECT INWARD SYSTEM ACCESS (DISA)
To provide the DISA with an AP (PN-AP01):
DESCRIPTION DATA
Assign the slot number to the PN-AP01 card. 
The SENSE Switch on the PN-AP01 card 
should be set to the slot number assigned by 
this command. (1) Slot No. (04-15)
(2) 07
Designate the processor for checking the 
DISA ID Codes.
Assign the ring rate on a DISA call.(1) 217 
(2) 1: AP (PN-AP01) 
(1) 180 
(2) 0/1: 0.2 sec. ON, 0.2 sec. OFF, 0.2 
sec. ON, 0.2 sec. OFF, 0.2 sec. 
ON, 0.2 sec. OFF/As per the data 
of CM35 YY = 33
For the programming procedure of this 
command, refer to AUTHORIZATION 
CODE with an AP.
Assign the data for DISA to the required 
trunks.• YY = 02 (Terminating System in Day 
Mode) 
• YY = 03 (Terminating System in Night 
Mode) 
(1) Trunk No. (000-255) 
(2) 16: DISA
• YY = 30 (Handling of busy/not avail-
able DISA destination in Day 
mode)
• YY = 31 (Handling of busy/not avail-
able DISA destination in Night 
mode)
(1) Trunk No. (000-255)
(2) 00: C.O. Line Release 
01: Forwarded to TAS
03: Forwarded to ATTCON 
04: Forwarded to DIT Station as-
signed by CM30 YY = 0. 
06: DT Connection for redial
08: C.O. Line Release CM05
CM08
CM30 START
A
CMD5
INITIAL 
						

							CHAPTER 2 ND-45670 (E)
Pag e 2 02
Revision 2.0
DIRECT INWARD SYSTEM ACCESS (DISA)
DESCRIPTION DATA
Assign the data for digit conversion on DID 
calls to the Route No. assigned by CM30 YY 
= 00 when providing DISA for DID calls. • YY = 18
(1) Trunk Route No. (00-63)
(2) 0/1: To be provided/Not to be pro-
vided 
When the data for CM35 YY = 18 is set to 0, 
assign the data for converting the received 
digit(s) to DISA. • Y = 0 (Day Mode) 
• Y = 1 (Night Mode) 
(1) X-XXXX: Station No. received 
(2) D16: DISA
Specify the maximum number of digits for 
ID Codes on DISA.
Note:The same number of digits must be
assigned by CM42-11 and CM42-
13. (1) 11, 13
(2) 01-10 (Maximum Number of Digits). If 
Check Code is provided, the 
maximum number of digits is 
limited to eight (8). If no data is 
set, 10 digits will be applied.
CM76
CM42
A
END
CM35 
						

							ND-45670 (E) CHAPTER 2
Page 203
Revision 2.0
DIRECT INWARD SYSTEM ACCESS (DISA)
To access the Digital Announcement Trunk (PN-2DATA) via DISA, add the following programming.
DESCRIPTION DATA
Assign a Digital Announcement Trunk 
Circuit No. to the required LEN.
Note:The Digital Announcement Trunk
Circuit No. must be assigned to the
first LEN (Level 0) and/or the third
LEN (Level 2) of each LT slot.(1) LEN (0000-0511) 
(2) EB000-EB127: Digital Announcement 
Trunk Circuit No. 
For PIM0/1: EB000-EB031  
For PIM2/3: EB032-EB063
For PIM4/5: EB064-EB095 
For PIM6/7: EB096-EB127 
Assign the Class of Service for Digital 
Announcement Trunk access to the required 
ID Code Serial No., when providing DISA 
without an Application Processor (PN-
AP01). • CM2A Y = 7 
(1) XX: ID Code Serial No. (00-07) as-
signed by CM2A Y = 5
(2) XX
 XX
*a: Service Rest. Class (A) (00-15  )
*b: Service Rest. Class (B) (00-15 )
• CM15 YY = 33 
(1) Service Rest. Class (A) (00-15) as-
signed by CM2A Y = 7 
(2) 1: Allowed 
Assign the Class of Service for Digital 
Announcement Trunk access to the required 
ID Code Serial No., when providing DISA 
with an Application Processor (PN-AP01).• CMD5 Y = 3 
(1) X-X---X: ID Code (Max Number of 
digits specified by CM42-
13)
(2) 201 XX
 0000 
*a: Service Rest. Class (A) (00-15  )
• CM15 YY = 33 
(1) Service Rest. Class (A) (00-15) as-
signed by CMD5 Y = 3 
(2) 1: Allowed 
To record and replay a message from an 
outside user, assign the Digital 
Announcement Trunk access code, 
respectively. • Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX : Access Code 
(2) A00 : Record
A01 : Replay 
CM10
END
START
CM20
CM2A
CM15
CMD5
CM15
*b *a
*a