NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 3 10
Revision 2.0
MUSIC ON HOLD
To provide External Hold Tone Source through PN-TNT Card (1200 Series Enhancement):
To provide External Hold Tone Source through PN-CP03 Card (1500 Series Enhancement):
DESCRIPTION DATA
Assign the TNT Circuit No. (External Hold 
Tone Source No. ) to the required LEN.(1) LEN (0000-0511)
(2) DA00-DA09: TNT Circuit No.
Note
Note:
The TNT Circuit No. must be as-
signed to the first LEN (Level 0)
and/or the third LEN (Level 2) of
each LT slot.
The TNT Circuit No. must be as-
signed for each tenant (One Exter-
nal Hold Tone Source can be
provided for each tenant).
Define the type of call to be provided with 
External Hold Tone.•Y=0
(1) 00: C.O. Line Call 
01: Tie Line Call
02: Internal Call
(1) 0200: External Hold Tone Source
Specify External Hold Tone Source per each 
tenant.•Y=1
(1) Tenant No. (00-63)
(2) 00-09: External Hold Tone Source No.
(TNT Circuit No. DA00-DA09)
Specify which tenant External Hold Tone is 
sent from.(1) 388
(2) 0: Tenant of held station/trunk
1
 : Tenant of holding station 
DESCRIPTION DATA
Define the type of call to be provided with 
Hold Tone.•Y=0
(1) 00:  C.O. Line Call
01:  Tie Line Call
02:  Internal Call
(1) 1400: Hold Tone Source through MP 
card
START
END
CM10
CM48
CM64
CM08
CM48
END
START 
						

							ND-45670 (E) CHAPTER 2
Page 311
Revision 2.0
MUSIC ON HOLD
HARDWARE REQUIRED
To provide External Hold Tone Source through PN-4COT and PN-DK00 card:
•PN-4COT
• PN-DK00
• External Hold Tone Source provided locally
Make the following connections between the trunks and the External Hold Tone Source at the MDF.
For details, refer to the MDF cross connection for an External Tone Source in the INSTALLATION PROCEDURE
MANUAL.
To provide the Hold Message by Digital Announcement Trunk:
• P N - 2 D ATA
PN-DK00 CARD PN-4COT CARDPBX
EXTERNAL HOLD TONE SOURCE
MDF 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 12
Revision 2.0
MUSIC ON HOLD
To provide the External Hold Tone Source through PN-TNT card:
•PN-TNT
• External Music Source provided locally
To connect the External Hold Tone Source, plug the cable into JACK0 or JACK1 on the PN-TNT card.
Set the switches on the PN-TNT card to adjust the External Hold Tone Source level.
• Level Control of External Hold Tone Source through JACK0/JACK1
No. 0 CIRCUIT (JACK0) No. 1 CIRCUIT (JACK1)
OUTPUT LEVEL SW-1 SW-2 OUTPUT LEVEL SW-3
SW-4
-10 dB OFF OFF -10 dB OFF OFF
-7 dB ON OFF -7 dB ON OFF
-4 dB OFF ON -4 dB OFF ON
-1 dB ON ON -1 dB ON ON
JACK0 or JACK1PN-TNT CARDPBX
EXTERNAL HOLD TONE SOURCE
SW SW
PN-TNT CARDON
12 34 
						

							ND-45670 (E) CHAPTER 2
Page 313
Revision 2.0
MUSIC ON HOLD
To provide External Hold Tone Source through PN-CP03 card:
• External Hold Tone Source provided locally.
To connect the External Hold Tone Source, plug the cable into JACK on the PN-CP03 card.
Set the switches on the PN-CP03 card as follows.
To provide Hold Tone Source on the MP card:  Set the JP1 switch to UP.
JAC K PN-CP03 CARDPBX
EXTERNAL HOLD TONE SOURCE
JP1
PN-CP03 CARD
VR
JP1:INTERNAL/EXTERNAL 
HOLD TONE
 SOURCE
VR:VARIABLE RESISTOR FOR 
EXTERNAL HOLD TONE SOURCE
(0-20k
W : CLOCKWISE)
20
0
DOWN:EXTERNAL HOLD 
TONE SOURCE
UP:INTERNAL HOLD TONE 
SOURCE
:  POSITION TO BE SET 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 14
Revision 2.0
NIGHT SERVICE: ATTENDANT NIGHT TRANSFER
PROGRAMMING 
DESCRIPTION DATA
Provide the system with Attendant Night 
Transfer. (1)  018: Attendant Night Transfer 
(2)  1 : To be provided 
Assign the Night Connection Station to each 
ATTCON Group. •  YY = 13
(1) ATTCON Group 0-3 (00-03) assigned 
by CM60 YY = 00 
(2) X-XXXX: Night Connection Station 
No.CM08 START
END
CM51 
						

							ND-45670 (E) CHAPTER 2
Page 315
Revision 2.0
NIGHT SERVICE: CALL REROUTING
PROGRAMMING 
Refer to Night Connection-Fixed/Flexible, Trunk Answer Any Station, Direct Inward Termination (DIT), Direct In-
ward Dialing (DID), and E&M Tie Line Access.  
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 16
Revision 2.0
NIGHT SERVICE: DAY/NIGHT MODE CHANGE BY ATTENDANT CONSOLE
PROGRAMMING
Note:The following trunk data (CM30) can be changed by this feature (depending upon programming).
Day (YY)
Night (YY)
02 03
04 05
13 14
15 16
30 31
DESCRIPTION DATA
Assign the password code for Day/Night 
Change by SN610 ATTCON.•  YY = 30
(1) 1 
(2)  XX-XX: Password Code (Max. 8 dig-
its)
X: 0-9, A(*), B(#)
If no data is set, the default setting is
NONE. In this case, the password is set
to “12345678.”
Assign the Day/Night mode key on SN610 
ATTCON.•  YY = 00
(1)  ATTCON No. +   + key No.
(2) F6110 
Assign the access code for providing Day/
Night Mode change from a SN610 
ATTCON, if required.•  Y = 0-3 (Numbering Plan Group 0-3) 
(1) X-XXX (Access Code) 
(2) A55 CM60 START
CM20
END
CM90
INITIAL
, 
						

							ND-45670 (E) CHAPTER 2
Page 317
Revision 2.0
NIGHT SERVICE: DAY/NIGHT MODE CHANGE BY STATION DIALING
PROGRAMMING 
Note:The following trunk data (CM30) can be changed by this feature (depending upon programming).
Day (YY)
Night (YY)
02 03
04 05
13 14
15 16
30 31
DESCRIPTION DATA
Provide the system with Day/Night Mode 
change by Station Dialing. (1)  244:  Change of Terminating System 
Incoming Trunk (CM30, YY = 
02/03) 
(2) 0: Available
(1)  245:  Change Trunk Restriction Class 
(CM30 YY = 02/03) 
(2) 0: Available 
Assign Service Restriction B to each station.  •  YY = 02
(1) X-XXXX (Station No.) 
(2) XX XX
*a: Service Restriction Class B (00-
15 ) 
Assign the Day/Night Mode Change by 
Station Dialing to Service Restriction B 
assigned by CM12 YY = 02. •  YY = 60
(1)  Service Restriction Class B (00-15) as-
signed by CM12 YY = 02
(2) 1 : Allowed
Assign the access code for Day/Night Mode 
change by Station Dialing.•  Y = 0-3 (Numbering Plan Group 0-3) 
(1)  X-XXX: Access Code (68) 
(2)  043:  Day/Night Mode Change by Sta-
tion Dialing 
Assign the Day/Night Mode Change by 
Station Dialing key on the Multiline 
Terminals. •  YY = 00
(1)  X-XXXX: Primary Extension No. +   
+ Key No. 
(2)  F0043: Day/Night Mode Change by 
Station Dialing
CM08 START
CM12
CM15
CM90
CM20
END
*a
, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 18
Revision 2.0
NIGHT SERVICE: NIGHT CONNECTION-FIXED
PROGRAMMING
To Provide Night Connection Stations.
DESCRIPTION DATA
Assign a Night Connection Station to each 
Incoming Trunk.•  YY = 03
(1) Trunk No. (000-255) 
(2)  04: Direct-In Termination
•  YY = 05
(1) Trunk No. (000-255) 
(2)  X-XXXX: Night Connection Station 
No.
Assign the destination to which a call is 
forwarded when the Night Connection 
Station is Busy/No Answer.•  YY = 14 (When Night Connection 
Station is busy.) 
(1) Trunk No. (000-255) 
(2)  01: To TAS
04: To SN610 ATTCON 
06: Automatic Camp-On 
15 : Keep the call ringing (Waiting 
until the Night Connection 
Station becomes idle.)
•  YY = 16 (When Night Connection 
Station is not answering) 
(1) Trunk No. (000-255) 
(2)  01: To SN610 ATTCON 
03: To TAS
15 : Keep the call ringing (Waiting 
until the Night Connection 
Station becomes idle.)
Specify the timing for a call forwarding when 
the Night Connection Station is No Answer.
Note:This timing is also applied to Call
Forwarding-No Answer, Attendant
Overflow, and Group Diversion.• Y = 0 
(1) 01 
(2)  01-30 : 4-120 sec. in 4 sec. increments
If no data is set, the default setting is 32-36
seconds.
CM30 START
END
CM41 
						

							ND-45670 (E) CHAPTER 2
Page 319
Revision 2.0
NIGHT SERVICE: NIGHT CONNECTION-FLEXIBLE
PROGRAMMING 
Refer to Night Connection-Fixed and Call Forwarding-All Calls.