NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Page 74 Addendum-002
Revision 2.2 JANUARY, 1999
ATTENDANT CONSOLE (SN716 DESKCON)
DESCRIPTION DATA
Specify the type of the Attendant Console.  •  YY=22
(1) ATTCON No. (0-7)
(2)  0 : SN716 DESKCON
1 : SN610 ATTCON
Allocate the ATT Group No. to each SN716
DESKCON.• YY=00
(1) ATTCON No. (0-7)
(2)  0: ATT GROUP 0
3: ATT GROUP 3
Specify the Master SN716 DESKCON within
the ATT Group assigned by YY=00. • YY=01
(1) ATTCON No. (0-7) 
(2) 0/1 : Master/Sub
When providing 2nd Ringing feature on the
SN716 DESKCON, make Off-Hook Ringing
effective.• YY=16
(1) ATTCON No. (0-7) 
(2)  0: To be provided
Specify the tenants to be handled by each ATT
Group.• Y=0-3
(1)  Tenant No. (00-63)
(2)  0/1 : To be handled/Not to be handledCM60
CM62
B
END
INITIAL
||
INITIAL
INITIAL 
						

							ND-45670 (E) CHAPTER 2
Page 75
Revision 2.0
ATTENDANT DELAY ANNOUNCEMENT
PROGRAMMING
DESCRIPTION DATA
Assign a Digital Announcement Trunk Circuit 
No. to the required LEN.
Note:The Digital Announcement Trunk
Circuit No. must be assigned to the
first LEN (Level 0) and/or the third
LEN (Level 2) of each LT slot. (1)  LEN (0000-0511)
 (2)  EB000-EB127: Digital Announcement 
Trunk Circuit No. 
For PIM0/1: EB000-EB031
For PIM2/3: EB032-EB063
For PIM4/5: EB064-EB095
For PIM6/7: EB096-EB127
Provide the Announcement Service via 
Digital Announcement Trunk on Attendant 
Delay Announcement.•  YY = 74
 (1)  Trunk Route No. (00-63)
 (2)  0/1 : Allowed/Restricted
Assign the function of the Digital 
Announcement Trunk Circuit.• YY = 00
(1) 000-127: Digital Announcement Trunk 
Circuit No. assigned by CM10 (EB000-
EB127)
(2) 0F
 XX:
*a: Attendant Delay Announcement
*b: Message No. (00-63)
• YY = 0A
(1) XX: Tenant No. 
(2) XX: Message No. (00-63) assigned by 
CM49 YY = 00
CM10 START
CM35
CM49
A
*b *a 
						

							CHAPTER 2 ND-45670 (E)
Pag e 7 6
Revision 2.0
ATTENDANT DELAY ANNOUNCEMENT
DESCRIPTION DATA
Specify the replaying of the message recorded 
in the Digital Announcement Trunk.(1) 165
(2) 0 : The message is replayed at an in-
terval assigned by CM41 Y= 0, 
Function No. 47.
1 : The message is played only once.
To record, replay, and delete a message, assign 
the Digital Announcement Trunk access 
codes, respectively. • Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code
(2) A00: Record
A01: Replay
A02: Delete
Specify the unanswered timing of message 
replay.•Y = 0
(1) 16
(2) 01-30 : 4 sec-120 sec. in 4-sec. incre-
ments
If no data is set, the default setting is 32-36 
seconds.
Specify the interval time of message replay. • Y = 0
(1) 47
(2) 01-30 : 4 sec.-120 sec. in 4-sec. incre-
ments
If no data is set, the default setting is 32-36 
seconds.CM08
A
CM20
CM41
END 
						

							ND-45670 (E) CHAPTER 2
Page 77
Revision 2.0
ATTENDANT OVERFLOW
PROGRAMMING
Note:Refer to the Automated Attendant feature programming section in this manual for assignment information
of the Automated Attendant when using the Automated Attendant as the Attendant Overflow destination.
DESCRIPTION DATA
Provide the system with ATTENDANT 
OVERFLOW.(1) 067
(2) 0: Available
Assign the data for terminating system in Day/
Night Mode for each trunk.• YY = 02 (Day Mode)
(1) Trunk No. (000-255)
(2) 14: Termination to SN610 ATTCON
• YY = 03 (Night Mode)
(1) Trunk No. 
(2) 04: DIT
09: Automated Attendant 
Note
• YY = 05 (Night Station Assignment)
(1) Trunk No. 
(2) X–XXXX (Station No.)
Specify the Timing Interval for 
ATTENDANT OVERFLOW.•Y = 0
(1) 01:
(2) 01-30 : 4-120 sec. in 4 sec. increments
If no data is set, the default setting is 32-36 
seconds.
CM08 START
CM30
CM41
END 
						

							CHAPTER 2 ND-45670 (E)
Pag e 7 8
Revision 2.0
ATTENDANT OVERRIDE
PROGRAMMING
DESCRIPTION DATA
Provide the system with ATTENDANT 
OVERRIDE.(1) 012
(2) 1 : Available
Specify the interval of the Warning Tone sent 
to the connected parties.(1) 045
(2) 0 : Only Once
1
 : Every 4 sec.
Specify whether the Warning Tone is sent to 
the outside party.(1) 076
(2) 0 : To be sent out.
1
 : Not to be sent out.
Assign Service Restriction Class (A) to each 
station.• YY = 02
(1) X-XXXX (Station No.)
(2) XX
 XX
*a: Service Restriction Class (A) (00-
15 )
Assign this feature to the Service Restriction 
Class (A) assigned by CM12 YY= 02.• YY = 09
(1) XX:Service Restriction Class (A) as-
signed by CM12 YY = 02.
(2) 1 : Allowed
Assign the access code for Individual Trunk 
Access.• Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX : Access Code
(2) 081 : Individual Trunk Access
Assign the Trunk Identification Code to each 
trunk.
Note:By loading the Resident System
Program, Trunk Identification Codes
are assigned as follows:
1XXX
*a: Trunk Number (000-255)• YY = 19
(1) Trunk No. (000-255)
(2) XXXX: Trunk ID Code
CM08 START
CM12
CM15
CM20
CM30
A
*a
*a 
						

							ND-45670 (E) CHAPTER 2
Page 79
Revision 2.0
ATTENDANT OVERRIDE
Note:This feature cannot be used in conjunction with Attendant Lockout.
DESCRIPTION DATA
Assign the BV key to SN610 Attendant 
Console.
Note:By Resident System Program, one of
the Multi-Function keys is assigned
as a BV key (when receiving Busy
Tone).• YY = 00
(1) ATTCON No. +   + Key No. 
(2) F6107: Busy Verification
CM90
END
A
, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 8 0
Revision 2.0
AUTHORIZATION CODE
PROGRAMMING
1. In a system with an Application Processor (PN-AP01) 
DESCRIPTION DATA
Assign a slot number to the PN-AP01 card 
according to the location of the card. 
Note:The slot number is given by the
SENSE switch on the PN-AP01 card.(1) Slot Number (04-15)
(2) 07: PN-AP01 card
Designate the AP card for this feature.(1) 216: Designates the Processor for the 
Authorization Code.
(2) 1 : AP (PN-AP01)
Specify whether Service Set Tone should be 
sent after dialing the access code for the 
Authorization Code.(1) 362: Provision of Service Set Tone after 
dialing the access code.
(2) 1 : Not to be provided/To be provided.
Assign the Class of Service for Authorization 
Code defined.• CM12 YY = 02
(1) X-XXXX: Station No. 
(2) XX
 XX
*a: Service Restriction Class (A): 
00-15
*b: Service Restriction Class (B): 
00-15
• CM15 YY = 31 (Authorization Code)
(1) Service Restriction Class (A) (00-15) 
Assigned by CM12 YY = 02
(2) 1 : Allowed
CM05 START
CM08
A
CM12
CM15
INITIAL
*b *a 
						

							ND-45670 (E) CHAPTER 2
Page 81
Revision 2.0
AUTHORIZATION CODE
DESCRIPTION DATA
Assign the access code for each Authorization 
Code.• Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code
(2) 086: Authorization Code
Specify the maximum number of digits for 
each Authorization Code.(1) 11: Authorization Code Max. digits
(2) Max. number of digits (01-10 ). 
If Check Code is provided, the maximum 
number of digits is limited to eight (8).
Note:CMD6 must be completed prior to
programming CMD5.
Set the SENSE1 switch on the DN-AP01 
Board, as shown below.
Load the initial data into the PN-AP01 by 
performing the following:
 + D60 +  + 0000 +   + CCC + 
After about 30 seconds the AP initialization is 
completed an the “RUN” lamp on the PN-
AP01 lights.
Set the SENSE1 switch on the PN-AP01 
board, as shown below.
CM20
B
A
CM42
CMD6
4
3
2
1: Switch position
ONSENSE1
ST DEDEEXE
4
3
2
1: Switch position
ONSENSE1 
						

							CHAPTER 2 ND-45670 (E)
Pag e 8 2
Revision 2.0
AUTHORIZATION CODE
DESCRIPTION DATA
Specify the conditions for adding a Check 
Code to each Authorization Code.
A Check Code consists of 2 digits:
The 1st and 2nd Check Code are generated by 
the AP according to the conditions specified 
by Y = 0 and Y = 1.
Authorization Code:
X
1 X2 X3 X4 X5 X6 X7 X8 C1 C2
 • Y = 0 (Designation of Significant digits 
for Check Code generation)
(1) 0: For 1st Check Code
1: For 2nd Check Code
(2) 00 X
 X: Significant digit designation
*a: 1st-4th digit (0-F) (See left column)
*b: 5th-8th digit (0-F)
If no Check Code is required, set data = 0000 
for both 1st and 2nd Check Code.
• Y = 1 (Setting of Check Sum Data for 
generating Check Code)
(1) 0: For 1st Check Code
1: For 2nd Check Code
(2) 0-9: Check Sum Data (Enter desired 
value)
C
CMD5
B
ID Code programmed  Check Code
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
XX2X3X4
X5X6X7X8
DIGIT
DATA
No Check Code
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
XX
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X: Significant Digit for Check Code1
*b *a 
						

							ND-45670 (E) CHAPTER 2
Page 83
Revision 2.0
AUTHORIZATION CODE
Note 1:Up to 1,000 Authorization codes combined with Forced Account Codes and Direct Inward System Access
(DISA) codes can be defined.
Note 2:When deleting all ID codes stored in the PN-AP01 card at one time, do the following operation:
 + D60 +   + 0000 +   + CCC +   
Note 3:When providing Mask Data for Authorization Codes, assign CMD001-160-175 (Refer to the SMDR System
Manual).
DESCRIPTION DATA
Set the Authorization Code and its temporary 
Class of Service.
By entering the Authorization Code, the 
Check Code will be displayed on the MAT or 
CAT.
• Temporary Class of Service
X
1: Type of Temporary Class of Ser-
vice
0: Unrestricted
1: Fully-Restricted
2: As per X
2-X9
9: Delete the ID Code
X
2X3: Trunk Restriction Class (01-08) 
specified by CM35 YY = 51-68.•Y = 3
(1) X-X...X: Authorization Code (Max. 
number of digits specified by CM42-11.)
(2) X
1 (Single Digit): When X1 = 0, 1 or 9
X
1X2...X9 (9 digits): When X1 = 2
(See left column)
X
4X5: Service Restriction Class (A) (01-15)
X
6X7: Service Restriction Class (B) (01-15)
X
8X9: Service Restriction Class (C) (01-15)
CMD5
C
END
As per CM15
ST
DEDEEXE