NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 3 30
Revision 2.0
PAD LOCK (1300 Series Enhancement)
DESCRIPTION DATA
(1) X XX
Status No. (1/2) 
02: Station cannot be called 
(Do Not Disturb Set)
03: Station can be called 
(Do Not Disturb Reset)
(2) 0 : No
1: Yes
(1) X
 XX
Status No. (1/2)
04~07 (See the above table)
(2) 0 : No
Specify the system to do not print the Maid 
Status Record out.(1) 150 (Maid Status Record Printing)
(2) 1: Not available
CMD031
D
CMD000
END 
						

							ND-45670 (E) CHAPTER 2
Page 331
Revision 2.0
PAD LOCK (1300 Series Enhancement)
2. In case of a system without AP card (PN-AP01):
DESCRIPTION DATA
Designate the MP card for Authorization 
Code.(1) 216: Designation of Processor for Au-
thorization Code
(2) 0: MP (PN-CP00) card
Specify the Service Set Tone after dialling the 
access code for Authorization Code.(1) 362: Provision of Service Set Tone after 
dialling the access code
(2) 1 : To be provided
Set the data for 281 to 1. (Maid ID Code is not 
used.)(1) 281
(2) 1 : Not available
Assign the Service Restriction Class (A) 
allowed for Authorization Code feature.• YY:31 (Authorization Code)
(1) Service Restriction Class (A) (00-15)
(2) 1t: Allowed
Assign allowed class and restricted class for 
Maid Status features.• YY=75 (Maid Status)
(1) Service Restriction Class (B) (00-15)
(2) 0: Restricted
1t: Allowed
To the station that uses PAD LOCK feature, 
assign the Service Restriction Class (A) 
allowed for Authorization Code feature. 
Moreover, to all the station, assign the Service 
Restriction Class (B) restricted for Maid 
Status feature.• YY=02
(1) X-XXXX: Station No.
(2) XX
 XX
Service Restriction Class (A)
Service Restriction Class (B)
Assign the access code for Authorization 
Code.• Y=0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code
(2) 086: Authorization Code
CM08
CM20
A
CM15
CM12 START 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 32
Revision 2.0
PAD LOCK (1300 Series Enhancement)
DESCRIPTION DATA
Specify the maximum number of digits for 
Authorization Code.(1)
(2)11: Authorization Code Max. digits
Max. number of digits
01: 1 digit
08: 8 digits
NONE : 8 digits
Set the Authorization Code. •
(1)
(2)Y=0
XX: Code Serial No. (00-99)
X-X...X: Authorization Code
Set the purpose and the Temporary Service
Class of each Authorization Code.•
(1)
(2)Y=1 (Purpose of the Code)
XX: Code Serial No. (00-99)
1 : Authorization Code
Service Restriction Class (B) of the Temporary
Service Class should be set to the allowed class
for Maid Status.•
(1)
(2)Y=3
XX: Code Serial No. (00-99)
XX
 XX:
Service Restriction Class (A) 
(00-15)
Service Restriction Class (B) 
(00-15) 
(Allowed class for Maid Status)
Assign the access code for Maid Status. •
(1)
(2)YY=0-3 (Numbering Plan Group 0-3)
X-XXX (Access Code)
029
Assign the Class of Service for Maid Status. (1)
(2)X-XXXX: Station No.
Service Class No. (00-15)
CM42
CM20
B
A
CM2A
CMD015
~
~ 
						

							ND-45670 (E) CHAPTER 2
Page 333
Revision 2.0
PAD LOCK (1300 Series Enhancement)
DESCRIPTION DATA
Assign the Maid Status Processing to the 
Service Class assigned by CMD015.(1) XX 06
Service Class No. assigned by
CMD015
(2) 1: Yes
Allow each Status Number (Restricted/
Normal) to change the Status Number from 
the station.
Note:Desired number can be assigned for
the Status Number of each status.(1) 1
 31
Status No. (Restricted) Note
Allowed to change the Status No.
from the station
(2) 1: Yes
(1) 2
 31
Status No. (Normal) Note
Allowed to change the Status No.
from the station
(2) 1: Yes
Assign the originating function, the incoming
call function, and the other function to each 
Status Number as following table.(1) 1
 00
Status No. (Restricted)
No originating allowed (Room
Cut Off)
(2) 1: Yes
(1) 1
 01
Status No. (Restricted)
Originating allowed (Room Cut
Off Reset)
(2) 0 : No
(1) 2
 00
Status No. (Normal)
No originating allowed (Room
Cut Off )
(2) 1: No
CMD016
CMD031
C
B
ROOM 
STATUS No.FUNCTION
00 01 02 03 04 05 06 07
1 
(Restricted)100/10/10000
2 
(Normal)010/10/10000 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 34
Revision 2.0
PAD LOCK (1300 Series Enhancement)
HARDWARE REQUIRED
PN-AP00 card
PN-AP01 card is required for providing the Authorization Code:
• exceeding 8 digits.
• with check code.
• total of more than 100 codes.
DESCRIPTION DATA
Assign the incoming call function to each 
Status Number.(1) 2
 01
Status No. (Normal)
Originating allowed 
(Room Cut Off Reset)
(2) 1: Yes
(1) X
 XX
Status No. (1/2)
02: Station cannot be called 
(Do Not disturb Set)
03: Station can be called 
(Do Not Disturb Reset)
(2) 0 : No
1: Yes
(1) X
 XX
Status No. (1/2)
04-~07
(See the above table)
(2) 0 : No
Specify the system to do not print the Maid 
Status Record out.(1) 150 (Maid Status Record Printing)
(2) 1:  Not available
CMD031
C
CMD000
END 
						

							ND-45670 (E) CHAPTER 2
Page 335
Revision 2.0
PERIODIC TIME INDICATION TONE
PROGRAMMING
DESCRIPTION DATA
Provide the system with this feature (for C.O 
lines).
Specify this service on a Tie Line Call.(1) 135
(2)  0: To be provided
(1) 136
(2)  0/1 : To be provided/Not to be 
provided.
Assign the Class of Service for this feature to 
the required stations.•  CM12 YY = 02 [Service Rest. Class B 
(00-15 )]
•  CM15 YY = 61
(1)  00-15 (Service Rest. Class B assigned by 
CM12 YY = 02) 
(2) 1 : Allowed
Assign as Ordinary Station the required 
stations. If assigned to 0 (Analog Data 
Station), this feature will not be applied to the 
station.•  YY = 07
(1) X-XXXX (Station No.)
(2) 1 : Ordinary Station
Specify the interval time for Periodic Time 
Indication Tone.•  Y = 0
(1) 09
(2)  00: 36 sec.
01-12: 64-724 sec. in 60 sec. increments
If no data is set, the default setting is 180-184 
seconds.CM08 START
CM41
CM12
CM15
END
CM13 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 36
Revision 2.0
POOLED LINE ACCESS
PROGRAMMING
DESCRIPTION DATA
Assign the Pooled Lines (Virtual Line Station 
Number) to the required Virtual LEN.
The Virtual LENs have no relation with the 
physical LEN used in CM10. Therefore, any 
Virtual LENs can be assigned to each Virtual 
Line Station Number. However, the Virtual 
Line Station Number should be different from 
the Single Line Number assigned by CM10.(1) Virtual LEN (0000-0255) 
(2)  X-XXXX (Virtual Line Station No.) 
Assign the Pooled Line keys to each Multiline 
Terminal. Pooled Lines 00-63 can answer a 
call terminated to Tenants 00-63 respectively, 
and can originate a call using Trunk Routes 
00-63 respectively.
Pooled Line 
Origination Termination
00  Trunk Route 00  Tenant 00 
01 01 01 
63 Trunk Route 63 Tenant 63 •  YY = 00
(1)  Primary Extension No. +   + Key No. 
(2)  F4100-F4163 (Pooled Line 00-63) 
CM11 START
CM90
A
, 
						

							ND-45670 (E) CHAPTER 2
Page 337
Revision 2.0
POOLED LINE ACCESS
HARDWARE REQUIRED 
ETJ-8-1/ETJ-16DC-1/ETJ-16DD-1/ETJ-24DS-1 and PN-2DLCB/4DLCA card. 
DESCRIPTION DATA
Assign a Trunk Route No. and Tenant No. to 
the trunks in the Pooled Line group. 
Note:Refer to the Command Manual for
the Resident System Program. •  YY = 00 (Trunk Route Allocation) 
(1) 000-255 (Trunk No.) 
(2)  00-63 (Trunk Route No.) 
Note
•  YY = 01 (Allocation of tenants to trunks) 
(1) 000-255 (Trunk No.) 
(2)  00-63 (Tenant No.) (00) 
Specify the terminating system, including 
TAS, of the trunks in the Pooled Line group.•  YY = 02 (Terminating System in Day 
mode) 
•  YY = 03 (Terminating System in Night 
mode) 
(1) 000-255 (Trunk No.) 
(2)  03: Trunk-Direct Appearances and TAS
13: TAS 
19: SN610 ATTCON + TAS
20: SN610 ATTCON + Trunk Direct 
Appearances + TAS 
Specify whether call terminating is indicated 
on the Pooled Line keys assigned by CM90-
F4100-F4163. (1) 116 
(2)  0/1 : Available/Not Available
END
CM30
A
CM08 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 38
Revision 2.0
POWER FAILURE TRANSFER
PROGRAMMING
To use the PN-AUC card:
To use the PZ-8PFT card:
No programming is required.
HARDWARE REQUIRED
PN-AUC card and PN-4COT card, or PZ-8PFT card.
Make the following connections between the cards. For details, refer to the MDF cross connection for the PFT in
the INSTALLATION PROCEDURE MANUAL.
DESCRIPTION DATA
Assign the PN-AUCA cards to the required 
LENs. (1) LEN: 0000-0511
(2)  X-XXXX: Station No. 
Assign the PN-4COT cards to the required 
LENs.(1) LEN: 0000-0511
(2)  D000-D255: Trunk No.CM10 START
END
To use the PN-AUC card:
To use the PZ-8PFT card:
...
..MD F
TO C.O. L INE PBX
MDF TEL
.....MDF
TO C.O. L INE PBX
MDF TEL.
MDF..
PN-4LCPN-4COT
PN-AUC
PN-4COT 
						

							ND-45670 (E) CHAPTER 2
Page 339
Revision 2.0
PRIORITY CALL
PROGRAMMING 
DESCRIPTION DATA
Assign the Class of Service for Priority Call to 
the required stations. •  CM12 YY = 02 (Service Rest. Class A 
00-15 ) 
• CM15 
•  YY = 17 (Priority Call 0) 
•  YY = 18 (Priority Call 1) 
(1)  00-15 (Service Restriction Class A as-
signed by CM12 YY = 02) 
(2) 1 : Allowed
Assign the access code for Priority Calls 0 and 
1 respectively. •  Y = 0-3 (Numbering Plan Group 0-3) 
(1)  X-XXX (Access Code) 
(2)  088: Priority Call 0 
089: Priority Call 1
Specify the destination for Priority Calls 0 and 
1. (1)  250 (For Priority Call 0) 
(2)  0: Same Station as Off Hook Alarm 
1 : SN610 ATTCON 
(1)  251 (For Priority Call 1) 
(2)  0: Same station as Off-Hook Alarm 
1 : SN610 ATTCON 
If CM08-250/251 is set to “1”, assign the Pri-
ority Calls 0 and 1 to any Priority Call Keys on 
SN610 ATTCON. •  YY = 00
(1)  ATTCON No. +   + Key No.
(2)  F6054: Priority Call 0 
F6055: Priority Call 1
If CM08-250/251 is set to “0”, assign the des-
tination of Priority Calls 0 and 1 to the desired 
station. •  YY = 12
(1)  Tenant No. (00-63) 
(2) X-XXXX (Station No.) 
CM51 START
CM08
CM12
CM15
END
CM20
CM90,