NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 3 72
Revision 2.0
STATION HUNTING: STATION HUNTING-SECRETARIAL
PROGRAMMING
DESCRIPTION DATA
Assign a Secretary Station Serial Number to 
each Station Hunting Group.
Note:A maximum of 31 extensions can be
members of the Secretarial Hunt
group.•Y=2
(1)  X-XXXX: Pilot Station No. (Terminal)/
All Member Station numbers 
(Circular)
(2) 00-30 (Secretary Station Serial No.)
Assign a station number to each Secretary Sta-
tion Serial Number assigned by CM18Y=2.•Y=0
(1) 00-30 (Secretary Station Serial Number)
(2) X-XXXX (Secretary Station No.)
Specify the Hunting capability of each Secre-
tary Station.•  Y = 1
(1)  00-30 (Secretary Station Serial No.)
(2)  5: Hunting (As per Y=2)
7: No Hunting
Assign the Secretary Station Numbers, one by 
one, in order of the desired Secretary Hunting, 
as shown below.
1st Operation
(1) Station A
(2) Station B
2nd Operation
(1) Station B
(2) Station C•Y=2
(1) X-XXXX (Secretary Station No.)
(2) X-XXXX (Another Secretary Station 
No. to be hunted to.)
Allow or restrict the ability to set Station 
Hunting-Secretarial for a station with Do Not 
Disturb set.(1) 240
(2) 0: Allow
1 : Restrict
START
END
CM18
CM19
CM08 
						

							ND-45670 (E) CHAPTER 2
Page 373
Revision 2.0
STATION MESSAGE DETAIL RECORDING (SMDR)
PROGRAMMING 
Refer to the SMDR System Manual.
HARDWARE REQUIRED 
Refer to the SMDR System Manual. 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 74
Revision 2.0
STATION SPEED DIALING
PROGRAMMING
1. To provide an Extension Memory card (PN-ME00) for extending memory for Station Speed Dialing and
One Touch keys:
DESCRIPTION DATA
Assign a slot number to the Extension Memory 
card. The slot number is given by the SENSE 
switch on the Extension Memory card.(1) 04-15 (Slot Number)
(2) 19 (PN-ME00 card)
Provide the system with the Extension 
Memory card.(1) 56
(2) 1: To be provided
START
CM05
CMD000
END
INITIAL 
						

							ND-45670 (E) CHAPTER 2
Page 375
Revision 2.0
STATION SPEED DIALING
2. To provide Single Line Telephone or Multiline Terminal:
DESCRIPTION DATA
Specify whether 1000-Slot Memory Block has 26 
digits or 16 digits memory buffers.
Note:When CM08-252 is assigned as 0, only
3000 Station Speed Dialing numbers
can be assigned, and 1000-Slot Memory
Block No. 0-2 contains 26-digits memo-
ry buffers. When CM08-252 is assigned
as 1, 4500 Station Speed Dialing num-
bers can be assigned, and 1000-Slot
Memory Block No. 0-4 contains 16-dig-
its memory buffers.(1) 252
(2) 0/1 : 26/16 digitsNote:Regardless of this data setting, a
maximum of 26 digits number can
be stored to Extension Memory
card’s memory area (1000-Slot
Memory Block No. 8-F).
Assign Service Restriction Class A to each sta-
tion.• YY = 02
(1) X-XXXX (Station No.)
(2) XX
 XX 
*a
*a: Service Restriction Class A 
(00-15 )
Assign this service to Service Restriction Class A 
assigned by CM12 YY = 02.• YY = 07
(1) 00-15: Service Restriction Class A
(2) 1 : Allowed
Assign access codes for Station Speed Dialing, 
Origination, Entry and Cancel, respectively.• Y = 0-3 (Numbering Plan Group 0-3)
(1) X-XXX: Access Code (#*, 7*, 7#)
(2) 064: Origination 
065: Entry 
066: Cancel
Specify whether to provide Toll Restriction for an 
outgoing call by Station Speed Dialing.(1) 035
(2) 0/1 : Not provided/Provided
Specify whether to set “#” dialing as paused data 
(1.5 sec.) or called number to C.O. line when 
DTMF station or Multiline Terminal dials “#” in 
the setting of Station Speed Dialing feature.(1) 168
(2) 0/1 : Paused data (1.5 sec.)/
Called number to C.O. line
START
CM08
CM12
CM15
CM20
CM08
A 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 76
Revision 2.0
STATION SPEED DIALING
DESCRIPTION DATA
Specify “*” dialing is set as programmable 
pause by CM41-38 or dialed digit when the 
DTMF station or Multiline Terminal dials “*” 
in the setting of the Station Speed Dialing fea-
ture.(1) 171
(2) 0/1 :Programmable pause by CM41-
38/Dialed digit
Allocate the memory area for Station Speed 
Dialing to each station. The memory block for 
storing one called number of Station Speed 
Dialing is called a “Memory Parcel”. An as-
sembly of 10-Memory Parcels is called a “10 
Slot Memory Block,” and one hundred 10-
Slot Memory Blocks are called a “1000-Slot 
Memory Block”.(1) X-XXXX (Station No.)
(2) X
 XX X XX 
*a *b *c *d 
(3) *a:000-Slot Memory Block No. 0-4,
8-F 
Note 1 
*b:Memory Start Block No. 00-99: 
(10-Slot Memory Block) 
Note 2 
*c:Facility for programming the 
dialed number from the Station
(0/1: Effective/Ineffective) 
*d:Number of blocks in Memory 
Parcel (01-10)
CM08
CM73
B
A
The number of Memory Parcels for a station is specified by the data shown below.
DataNumber of 
Memory Parcels
Abbreviated Codes required for accessing this feature
are automatically given to each station, depending on
the number of Memory Parcels specified. XXXX01 10
XXXX10 100
0
4 1
2
3 1000-Slot
Memory Block0
9 1 Memory Parcel00
99 01 10-Slot
Memory Block1000 Memory Parcels
1000 Memory Parcels
1000 Memory Parcels
1000 Memory Parcels
500 Memory Parcels 
						

							ND-45670 (E) CHAPTER 2
Page 377
Revision 2.0
STATION SPEED DIALING
DESCRIPTION DATA
Note 1:
If the system provides the Extension Memory card, 1000-Slot Memory Block No. 8-F (8000
Memory Parcels) can be used. For using this memory area, there are several conditions as
mentioned below: 
• This memory area cannot be used for Speed Dialing with Speed Dialing keys provided
by CM90-second data: F11XX on a Multiline Terminal, and cannot also be used for
System Speed Dialing.
• When exchanging an Extension Memory card for another, data setting for this memory
area must be recommenced.
• The Office Data in this memory area cannot be saved and loaded by MAT operations.
Note 2:When the 1000-Slot Memory Block specifier is 4, Memory Start Block No. should be set to
00-49.
Less than 100 Memory Parcels for a station: In excess of 100 Memory Parcels for a station:
Assign the number to be dialed to each Mem-
ory Slot Number, if required. The numbers to 
be called are usually set from individual sta-
tions by their station users.(1) X
 XXX (Memory Slot No.) 
*a  *b 
*a: 1000-Slot Memory Block Num-
ber (0-4, 8-F) 
*b: 000-999
(2) Stored No. Setting Method: 
Outgoing Call Access Code (Max. 2 dig-
its) +   + Stored Number (Max. 
16/26 digits)
To set a pause into the Stored No., enter 
“C” (Fixed Pause=1.5 sec.) or “D” 
(Programmable Pause specified 
by CM41-38) after desired digits.
B
CM74
C
0
9 1 Memory Parcel
10-Slot
Memory
Block X
Memory Parcel
0
9 1
0
9 1
10-Slot 
Memory 
Block X
99
10-Slot 
Memory 
Block XX 0
1
99
Abbreviated Codes
, 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 78
Revision 2.0
STATION SPEED DIALING
DESCRIPTION DATA
Assign Station Speed Dialing keys on each 
Multiline Terminal, if required.• YY=00
(1) Primary Extension No. +   + Key No. 
(01-24)
(2) F11XX
 
*a 
*a: 00: Station Speed Dialing 00 
99: Station Speed Dialing 99
CM90
C
END
, 
						

							ND-45670 (E) CHAPTER 2
Page 379
Revision 2.0
STATION SPEED DIALING
3. To provide Multiline Terminal with One Touch keys (ETJ-16DD-1/ETJ-24DS-1/DTP-32-1/DTP-32D-1):
DESCRIPTION DATA
Specify whether 1000-Slot Memory Block has 
26 digits or 16 digits memory buffers.
Note 1:When CM08-252 is assigned as 0,
only 3000 Station Speed Dialing
numbers can be assigned, and 1000-
Slot Memory Block No. 0-2 contains
26-digits memory buffers. When
CM08-252 is assigned as 1, 4500
Station Speed Dialing numbers can
be assigned and 1000-Slot Memory
Block No. 0-4 contains 16-digits
memory buffers.(1) 252
(2) 0/1 : 26/16 digitsNote 2:Regardless of this data setting, a
maximum of 26 digits number can be
stored to Extension Memory card’s
memory area (1000-Slot Memory
Block No. 8-F).
Assign Service Restriction Class A to each 
station.• YY = 02 (Service Restriction Class A·B)
(1) X-XXXX (Station No.)
(2) XX
 XX 
*a
*a: Service Restriction Class A 
(00-15 )
Assign this service to Service Restriction 
Class A assigned by CM12 YY = 02.• YY = 07
(1) 00-15: Service Restriction Class A
(2) 1 : Allowed
Specify whether to provide Toll Restriction for 
an outgoing call by Station Speed Dialing.(1) 035
(2) 0/1 : Not provided/Provided
Specify whether to set “#” dialing as paused 
data (1.5 sec.) or called number to C.O. line 
when Multiline Terminal dials “#” in the set-
ting of Station Speed Dialing feature.(1) 168
(2) 0/1 : Paused data (1.5 sec.)/
Called number to C.O. line
Specify whether to set “*” dialing as program-
mable pause by CM41-38 or dialed digit when 
DTMF station or Multiline Terminal dials “*” 
in the setting of Station Speed Dialing feature.(1) 171
(2) 0/1 : Programmable pause by CM41-
38/Dialed digit
START
CM08
A
CM12
CM15
CM08 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 80
Revision 2.0
STATION SPEED DIALING
DESCRIPTION DATA
Allocate the memory area for Station Speed 
Dialing to each station. 
The memory block for storing one called 
number of Station Speed Dialing is called a 
“Memory Parcel”. 
An assembly of 10-Memory Parcels is called 
a “10 Slot Memory Block,” and one hundred 
10-Slot Memory Blocks are called a “1000-
Slot Memory Block”.(1) X-XXXX (Primary Extension No.)
(2) X
 XX 0 XX 
*a *b  *c 
*a: 1000-Slot Memory Block No. 
(0-4, 8-F) 
*b: Start of 10-Slot Memory Block 
No. (00-49) 
*c: Number of 10-Slot Memory 
Blocks 02: ETJ-16DD-1/ETJ-
24DS-1 
(20 numbers)
The ETJ-16DD-1/ETJ-24DS-1 requires two 
10-Slot Memory Blocks (20 numbers).
Note:1000-Slot Memory Block No. 8-F
can be used when the system pro-
vides the Extension Memory card.
If assigning the station number to
One Touch keys using this memory
area, the lamp does not show the
busy state.
CM94
A
END
0
4 1
2
3 1000-Slot
Memory Block0
9 1 Memory Parcel00
99 01 10-Slot
Memory Block1000 Memory Parcels
1000 Memory Parcels
1000 Memory Parcels
1000 Memory Parcels
500 Memory Parcels
00
49 01 
						

							ND-45670 (E) CHAPTER 2
Page 381
Revision 2.0
STATION SPEED DIALING
4. To provide the One Touch key to send “Hooking Signal + Called Number” to a Centrex, set the following
data in addition to the programming (2). (1500 Series Enhancement)
 
5. To provide the One Touch key to send “Called Number + DTMF Signal” for such as VMS operation, set
the following data in addition to the programming (2), when the called number includes a trunk access code.
If the called number includes no trunk access code, this data is not required. (1500 Series Enhancement)
DESCRIPTION DATA
Assign the access code for sending of a Hook-
ing signal to a Centrex.
Maximum of two digits are available.•Y = 0-3
(1) X-XX: Access code
(2) A58: Hooking signal to a Centrex
Assign a RECALL key on the Multiline Ter-
minal. RECALL key is used to return to a 
former line.• YY = 00
(1) Primary Extension No. +   + key No.
(2) F1015: RECALL
Provide Centrex trunk route with Centrex 
function.• YY = 86
(1) Trunk Route No. (00-63)
(2) 0: Centrex
DESCRIPTION DATA
Specify whether to set consecutive dialing “* 
#” as a delimiter between the called number 
and the DTMF signal.(1) 448
(2) 0 : *# (as it is)
1 : Delimiter between called number 
and DTMF signal
CM35 START
END
CM20
CM90
,
START
END
CM08