NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 3 56
Revision 2.0
PROPRIETARY MULTILINE TERMINAL: RING FREQUENCY CONTROL
PROGRAMMING 
To control the ring frequency by system data programming;
DESCRIPTION DATA
Enable the frequency control by system data 
programming.(1) 390 
(2)  1 : By System Data Programming 
Specify the ring frequency of each Multiline 
Terminal for internal calls. • CM12 YY = 07 [Service Restriction 
Class (C) (00-15 )] 
• CM15 YY = 83, 84
(1)  00-15 (Service Rest. Class (C) assigned 
by CM12 YY = 07) 
(2)  0/1 : See left column 
Specify the ring frequency for incoming calls 
on each trunk route.•  YY = 34
(1)  00-63 (Trunk Route No.) 
(2)  0: 1204 + 1285 [Hz] ´ 16 [Hz] 
1: 480 + 606 [Hz] ´ 8 [Hz]
2: 600 + 700 [Hz] 
3 : 480 + 606 [Hz] ´ l6 [Hz] 
START
END
CM12
CM15
CM08
CM35
INITIAL
YY
RING FREQUENCY
83 84
0 0 600 + 700 [Hz]
1 0 1024 + 1285 [Hz] x 16 [Hz]
0 1 480 + 606 [Hz] x 8 [Hz]
1 1 480 + 606 [Hz] x 16 [Hz] 
						

							ND-45670 (E) CHAPTER 2
Page 357
Revision 2.0
PROPRIETARY MULTILINE TERMINAL: RING FREQUENCY CONTROL
To control the ring frequency at the Multiline Terminal:
HARDWARE REQUIRED 
Multiline Terminal and DLC card
DESCRIPTION DATA
Disable ring frequency by system data pro-
gramming.(1) 390 
(2) 0: By depressing FNC key and dialing 3 
(1) 262
(2) 0
Assign one of the following ring frequencies 
to each Multiline Terminal for internal calls.• CM12 YY = 07
(1) X-XXXX: Primary Extension No.
(2) XX: Service Restriction Class C
(00-15 )
• CM15 YY = 83, 84
(1) 00-15: Service Restriction Class C
(2) 0/1 : See left column
Assign one of the ring frequencies for incom-
ing calls via each trunk route except for 600 + 
700 [Hz] (2nd Data = 2).• YY = 34
(1) 00-63 (Trunk Route No.) 
(2) 0 : 1024 + 1285 [Hz] ´ 16 [Hz] 
1 : 480 + 606 [Hz] ´ 8 [Hz]
3 : 480 + 606 [Hz] ´ 16 [Hz] 
START
END
CM12
CM15
CM08
CM35
INITIAL
YY
RING FREQUENCY
83 84
0 0 600 + 700 [Hz]
1 0 1024 + 1285 [Hz] x 16 [Hz]
0 1 480 + 606 [Hz] x 8 [Hz]
1 1 480 + 606 [Hz] x 16 [Hz] 
						

							CHAPTER 2 ND-45670 (E)
Page 358 Addendum-002
Revision 2.2 JANUARY, 1999
PROPRIETARY MULTILINE TERMINAL: SOFT KEY
PROGRAMMING
DESCRIPTION DATA
Specify whether Soft Key feature is avail-
able to each Multiline Terminal.• YY=22
(1) X-XXXX: Primary Extension No. 
(2) 0 : Available
1 : Not available
Assign Soft Key Pattern to each Multiline
Terminal.• YY=23
(1) X-XXXX: Primary Extension No. 
(2) 0 : Soft Key Pattern No. 0
1 : Soft Key Pattern No. 1
2 : Soft Key Pattern No. 2
3 : Soft Key Pattern No. 3CM12 START
A 
						

							ND-45670 (E) CHAPTER 2
Addendum-002 Page 359
JANUARY, 1999 Revision 2.2
PROPRIETARY MULTILINE TERMINAL: SOFT KEY
DESCRIPTION DATA
Assign the function of each Soft Key on each
status of the Multiline Terminal.
To the 2nd data of this command, the 2nd data
(F0XXX, F1XXX, F50XX) of CM90 should
be assigned except for Scroll Key data
(F5002).
The LED shows a maximum of 4 Soft Keys at
once. If assigning more than 4 Soft Keys on
one status, it is necessary to assign Scroll key
at every 4 keys (on 1st through 4th display).
Note 1:
Scroll key must be assigned as a key
for each active display.
Note 2:
Help key is only available in Pattern
No. 3.
Note 3:
For the Pattern No. 3, the initial Soft
Key data for NEAX Mail AD-8 live
recording is assigned. See the fol-
lowing section.
Note 4:
Pattern No. 3 is fixed. If Pattern No.
3 is changed, only way to reset to de-
fault is to clear all data in PBX and
load the Resident System Program.• YY=00-03 (Soft Key Pattern No. 0-3 as-
signed by CM12 YY=23)
(1) XX
 XX 
*a: Status Number 00-15
00: Idle state
01: During dialing (Holding no call) 
02: During dialing (Holding station/
trunk)
03: During calling (Holding no call) 
04: During calling (Holding station/
trunk) 
05: Being called 
06: When called party is busy
(Holding no call)
07: When called party is busy
(Holding station/trunk) 
08: When called party is setting 
DND
09: Trunk busy
10: During speaking (Holding no 
call) 
11: During speaking (Holding sta-
tion/trunk)
12: During live recording/after live 
recording to NEAX Mail AD-8
Note 3
13-15: Not used
*b: Soft Key No. 00-15
00-03: Indicated on 1st display
04-07: Indicated on 2nd display 
08-11: Indicated on 3rd display
12-15: Indicated on 4th display
(2) F5002 : Scroll key to change Soft Key 
Indication
XXXXX: Setting of each function 
(Same as “F0XXX, F1XXX, 
F50XX” of CM90)
Assign the Characters indicated on each status
of the Multiline Terminal, corresponding to
the Soft Key function assigned by CM9A
YY=00-03.• YY=10-13 (Soft Key Pattern No. 0-3 as-
signed by CM12 YY=23)
(1) Same as YY=00-03
(2) Characters (Max. 6 characters)
See the following page.
CM9A
A
END
*a *b 
						

							CHAPTER 2 ND-45670 (E)
Page 359-1 Addendum-002
Revision 2.2 JANUARY, 1999
PROPRIETARY MULTILINE TERMINAL: SOFT KEY
NAME ASSIGNMENT
Character Code Table
234567
0
0@P \ p
1!1AQaq
2”2BRb r
3#3CSc s
4$4DTd t
5%5 EU e u
6&6 FV f v
7’7GWgw
8(8HXhx
9)9IYiy
A*:JZjz
B+;K[k{
C,N^n®
F/?O_o¬ 
						

							ND-45670 (E) CHAPTER 2
Addendum-002 Page 359-2
JANUARY, 1999 Revision 2.2
PROPRIETARY MULTILINE TERMINAL: SOFT KEY
To provide the Soft Keys for NEAX Mail AD-8 live recording, assign the following data. (1900 Series Release 2
Enhancement)
HARDWARE REQUIRED 
Multiline Terminal with Soft Keys (DTP-8D-1, DTP-16D-1, DTP-32D-1) and DLC card 
DESCRIPTION DATA
Provide the Record key on the feature key of
the Muliline Terminal.• YY=00
(1) Primary Extension No. +   + Key No. 
(01-16)
(2) F1091 (Record)
Assign the function of each Soft Key for
NEAX Mail AD-8 live recording.
Note:
For the Pattern No. 3, the initial Soft
Key data for NEAX Mail AD-8 live
recording is assigned as follows.• YY=00-03 (Soft Key Pattern No. 0-3 as-
signed by CM12 YY=23)
(1) 12 XX
Soft Key No. 00-15
00-03: Indicated on 1st display
04-07: Indicated on 2nd display
08-11: Indicated on 3rd display
12-15: Indicated on 4th display
(2) F1092: Pause
F1093: Re-record
F1094: End
F1095: Erase
F1096: Address
F1097: Urgent Page
• YY=10-13 (Soft Key Pattern No. 0-3 as-
signed by CM12 YY=23)
(1) Same as YY=00-03
(2) Characters (Max. 6 characters)
See previous page.
CM90 START
CM9A
END
,
CM9A YY=03  CM9A 
YY=13 
Indication 1st Data 2nd Data
1200 F1096 (Address) Addrs
1201 F1092 (Pause) Pause
1202 F1094 (End) End
1203 F5002 (Scroll) >>>>
1204 F1093 (Re-record) ReRec
1205 F1095 (Erase) Erase
1206 F1017 (MIC) MIC
1207 F5002 (Scroll) >>>>
1208 F1097 (Urgent Page) Urgnt
1209 NONE
1210 NONE
1211 F5002 (Scroll) >>>> 
						

							CHAPTER 2 ND-45670 (E)
Page 359-3 Addendum-002
Revision 2.2 JANUARY, 1999
REMOTE HOLD
(1900 Series Release 2 Enhancement)
PROGRAMMING
DESCRIPTION DATA
Assign Service Restriction Class (A) to each
station.• YY=02
(1) X-XXXX: Station No. 
(2) XX: Service Restriction Class (A)
(00-15 )
Assign this service to Service Restriction
Class (A) assigned by CM12 YY=02.• YYY=124
(1) XX: Service Restriction Class (A) as-
signed by CM12 YY=02.
(2) 0: Allowed
Specify the recall timing for Remote Hold. • Y=0
(1) 06
(2) 01-98: 4-392 sec. in 4 sec. increments
99: Recall is not performed
If no data is set, the default setting is 236-240
seconds.
Assign a Hold key to the Multiline Terminal.  • YY=00
(1) Primary Extension No. +   + Key No.
(2) F1010
START
CM41
CM12
END
CM15
CM90
, 
						

							ND-45670 (E) CHAPTER 2
Addendum-002 Page 359-4
JANUARY, 1999 Revision 2.2
This page is for your notes. 
						

							CHAPTER 2 ND-45670 (E)
Pag e 3 60
Revision 2.0
RESIDENT SYSTEM PROGRAM
PROGRAMMING 
No programming is required. (For the details of programmed system data, refer to the Command Manual.)  
						

							ND-45670 (E) CHAPTER 2
Page 361
Revision 2.0
RETURN MESSAGE SCHEDULE DISPLAY
PROGRAMMING 
HARDWARE REQUIRED
ETJ-8-1/ETJ-16DC-1/ETJ-16DD-1/ETJ-24DS-1 and PN-2DLCB/PN-4DLCA card. 
DESCRIPTION DATA
Assign the Class of Service for setting a Re-
turn Message Schedule. •  CM12 YY = 02 
(1) X-XXXX (Station No.) 
(2) XX
XX
*a: Service Restriction Class A (00-
15 ) 
•  CM15 YY = 19 
(1) Service Restriction Class A (00-15) as-
signed by CM12 YY = 02
(2) 1 : Allowed 
Assign whether the call to a station, set for Re-
turn Message Schedule Display, gets ringing 
or Reorder Tone.(1) 334 
(2) 0: Available (Ringing) 
1 : Not Available (ROT Connection) 
Assign an access code for Return Message 
Schedule set and cancel, respectively. •  Y = 0-3 (Number Plan Group 0-3) 
(1)  X-XXX: Access Code (#8) 
(2)  A54: Return Message Schedule Display 
Set
023: DND and/or Return Message 
Schedule Display Cancel
START
END
CM12
CM15
CM08
CM20
*a