NEC Neax2000 Ivs Feature Programming Manual
Have a look at the manual NEC Neax2000 Ivs Feature Programming Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 1 ND-45670 (E) Pag e 1 4 Revision 2.0 INTRODUCTION Figure 1-4 DSS Console Key Numbers 00 01 02 03 04 0506 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 EDW-48-2 34
ND-45670 (E) CHAPTER 1 Page 15 Revision 2.0 INTRODUCTION Figure 1-4 DSS Console Key Numbers (Continued) 00 06 12 18 24 30 36 42 48 54 55 56 57 58 5949 50 51 52 53 43 44 45 46 47 37 38 39 40 4131 32 33 34 35 25 26 27 28 29 19 20 21 22 23 13 14 15 16 1707 08 09 10 1101 02 03 04 05 DCU-60-1
CHAPTER 1 ND-45670 (E) Pag e 1 6 Revision 2.0 INTRODUCTION Figure 1-5 Add-On Module Key Numbers 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 EDW-48-2
ND-45670 (E) CHAPTER 1 Page 17 Revision 2.0 INTRODUCTION Figure 1-5 Add-On Module Key Numbers (Continued) 30 36 42 48 54 60 66 72 78 84 85 86 87 88 8979 80 81 82 83 73 74 75 76 77 67 68 69 70 7161 62 63 64 65 55 56 57 58 59 49 50 51 52 53 43 44 45 46 4737 38 39 40 4131 32 33 34 35 DCU-60-1
CHAPTER 1 ND-45670 (E) Pag e 1 8 Revision 2.0 INTRODUCTION This page is for your notes.
ND-45670 (E) CHAPTER 2 Page 19 Revision 2.0 CHAPTER 2 FEATURE PROGRAMMING 1. GENERAL This section provides the description for programming each service feature. 2. DESCRIPTION OF SERVICE FEATURES The description of each service feature comprises the following items: • PROGRAMMING This section provides the procedures for programming the service feature. If the service feature is function- ing in conjunction with other features, refer to the sections containing the information pertaining to those features. In the programming procedure, the meaning of (1), (2), and the icons are as follows: (1) : 1st Data (2) : 2nd Data : Initial Data With the system data clear command (CM00, CM01), the data with this marking ( ) is automatically as- signed for each command. : System Initialization : After entering the data, system reset is required (press SW1 on the MP card). • HARDWARE REQUIRED In this section, any hardware required for the feature (such as an interface card or external drive) is listed, with the exception of the following: (a) Single-line telephone set and interface card (PN-4LC) (b) Central Office Trunk Card (PN-4COT) Note:For Series E Multiline Terminals (DTP-8-1, DTP-8D-1, DTP-16-1, DTP-16D-1, DTP-32-1, DTP-32D-1), the feature programming is available in same method as the Series III Multiline Terminal. However, when the Series E Multiline Terminal with Series III mode or the Elite Terminal is accommodated, it is necessary to specify the kind of the terminal accommodated in a DLC card by programming of CM12 Y= 17. Refer to “Proprietary Multiline Terminal” for the programming of CM12 YY = 17. The feature programming for SN716 DESKCON is available in same method as the SN610 ATTCON. However, it is necessary to specify the type of console by programming of CM60 YY=22. Refer to “SN716 DESKCON” for programming related to SN716 DESKCON. INITIAL
CHAPTER 2 ND-45670 (E) Pag e 2 0 Revision 2.0 ACCOUNT CODE 2.1 Business Features PROGRAMMING HARDWARE REQUIRED SMDR (PN-AP00 card and cables) DESCRIPTION DATA Specify whether Service Set Tone should be sent after dialing the access code for Account Code entry. (1) 362 (2) 0/1 : No Tone/Service Set Tone (SST) Assign the Class of Service for Account Code entry to the required stations.• CM12 YY = 02 (1) X-XXXX: Primary Extension No. (2) XX XX *a: Service Restriction Class (A): 00- 15 • CM15 YY = 30 (1) 00-15 : Service Restriction Class (A) assigned by CM12 YY = 02 (2) 1 : Allowed Specify the maximum number of digits for Account Codes. Note: If the SMDR message format (2400 IMS Format) is assigned, the maxi- mum number of digits is 10. (See CM D001-82/102/122 in the SMDR Sys- tem Manual.)(1) 10 : Max. number of digits for Ac- count Codes (2) 01-16 : Max. number of digits If no data is entered, the default is 10. Assign an access code for Account Code en- try. • Y = 0-3: Numbering Plan Group 0-3 (1) X-XXX: Access Code (* #) (2) 085 Assign an Account Code feature access key to a Multiline Terminal. • YY = 00 (1) Primary Extension No. + + Key No. (2) F0085 CM08 START END CM42 CM20 CM90 CM12 CM15*a ,
ND-45670 (E) CHAPTER 2 Page 21 Revision 2.0 ADD-ON MODULE (1200 Series Enhancement) PROGRAMMING DESCRIPTION DATA Assign the Add-On Module Number to its associated LEN. Note:When the data assignment of both DSS Console and Add-On Module are required, the same number (the last two digits of the data) cannot be used.(1) 0000-0511 (LEN No.) (2) EC00-EC31: Add-On Module No. For PIM0/1: EC00-EC07 For PIM2/3: EC08-EC15 For PIM4/5: EC16-EC23 For PIM6/7: EC24-EC31 Assign the Multiline Terminal which will be associated with the Add-On Module. Note:The Multiline Terminal and the Add- On Module must be in the same PIM (Port Interface Module).•Y=0 (1) 00-31 (Add-On Module No.: Last two digits of EC00-EC31 assigned by CM10.) (2) X-XXXX (Primary Extension Number) Note Assign the Class of Service for the accommodation of Single-Line Telephone to Multiline Terminal. (Assignment for Single- Line Telephone only).• YY=05 (1) X-XXXX: Station No. (2) 0: Accommodated Assign the station and trunk numbers to the keys on each Add-On Module. Note:Single-Line, Virtual Line or Primary Extension can be assigned on Add- On Module.• YY=00 (1) Primary Extension No. + + Add-On Module Key No. (30-54) (2) X-XXXX (Station No.) Note DXXX *a *a: 000-255 (Trunk No.) START CM10 A CM12 CM90 CM98 Note ,
CHAPTER 2 ND-45670 (E) Pag e 2 2 Revision 2.0 ADD-ON MODULE (1200 Series Enhancement) PROGRAMMING DESCRIPTION DATA Assign the Automatic/Manual/Dial Intercom key to each Add-On Module, if required. For details, refer to INTERCOM.• YY=00 (1) Primary Extension No. + + Add-On Module Key No. (30-54) (2) A000 A031 Automatic Intercom No. A100 A131 A200 A700 A201 A701 Manual Intercom No. A224 A724 B000 B900 B001 B901 Dial Intercom No. B024 B924 Assign the Station Speed Dialing to the keys on each Add-On Module, if required. For details, refer to STATION SPEED DIALING.• YY=00 (1) Primary Extension No. + + Add-On Module Key No. (30-89) (2) F11XX *a *a: 00: Station Speed Dialing 00 99: Station Speed Dialing 99 CM90 A B , ,
ND-45670 (E) CHAPTER 2 Page 23 Revision 2.0 ADD-ON MODULE (1200 Series Enhancement) HARDWARE REQUIRED DSS Console PN-2DLC/4DLC Card (Two or four DSS Console can be accommodated per card) DESCRIPTION DATA Assign the Day/Night Key on each Add-On Module, if required.• YY=00 (1) Primary Extension No. + + Add-On Module Key No. (87-89) (2) F0043: Day/Night Key Specify the tone ringer enabled on call termination to each line/trunk key on each Add-On Module, if required.• YY=01 (1) Primary Extension No. + + Add-On Module Key No. (30-54) (2) 0/1 : Disabled/Enabled Assign the Delayed Ringing feature to each line/trunk key on an Add-On Module, if required. Note:Delayed Ringing can be assigned to the first 16 line/trunk keys (Key No. 30-45).• YY=03 (1) Primary Extension No. + + Add-On Module Key No. (30-45) Note (2) 0: Delayed Ringing Specify the Delayed Ringing timing. • Y=1 (1) 09 (2) 01-20: Timer Data for 2 sec. - 40 sec. (2 sec. increment) If no data is set, the default setting is 10 seconds. Provide Trunk-Direct Appearances to the trunk number.• YY=18 (1) Trunk No. (000-255) (2) 0: To be provided CM90 B END CM41 CM30 , , ,