NEC Neax2000 Ivs Feature Programming Manual

							CHAPTER 2 ND-45670 (E)
Pag e 1 04
Revision 2.0
AUTOMATIC CAMP-ON
PROGRAMMING
DESCRIPTION DATA
Specify the Camp-On Tone pattern. (1) 068
(2) 0/1 : Sent out once/Sent out periodi-
cally (4- intervals)
Assign Automatic Camp-On to the required 
DIT Trunks.• YY = 13 (In Day mode)
• YY = 14 (In Night mode)
(1) Trunk No. (000-255)
(2) 06: Automatic Camp-OnCM08 START
END
CM30 
						

							ND-45670 (E) CHAPTER 2
Page 105
Revision 2.0
AUTOMATIC NUMBER IDENTIFICATION (ANI) 
(1300 Series Enhancement)
PROGRAMMING
1. DTI Assignment for ANI
DESCRIPTION DATA
Assign a trunk Route Number to each DTI. • YY=00 
(1) Trunk No. (000-255) 
(2) Trunk Route No. (00-63)
Specify the Terminating System in Day Mode 
and Night Mode for incoming calls.• YY=02 (Day Mode) 
• YY=03 (Night Mode) 
(1) Trunk No. (000-255) 
(2) 31 : DID, TIE and any call which is not 
handled by the PBX
Assign the trunk Route data to each DTI route. • YY=00  (Kind  of  Trunk  Route) 
(1) Trunk Route No. (00-63) 
(2) 00: DDD (C.O./DID), ISDN Trunk
• YY=04 (Answer Signal from Distant Of-
fice)  
(1) Trunk Route No. (00-63)  
(2) 2: Answer signal arrives
• YY=05 (Release Signal from Distant Of-
fice) 
(1) Trunk Route No. (00-63) 
(2) 1 :Release Signal arrives
• YY=09 (Incoming Connection Signaling)
(1) Trunk Route No. (00-63) 
(2) 03: Wink Start
• YY=10 (2nd DT Sending on Call Termi-
nation)  
(1) Trunk Route No. (00-63) 
(2) 0: 2nd Dial Tone is not sent.
A
CM35
CM30 START
t
t 
						

							CHAPTER 2 ND-45670 (E)
Page 106 Addendum-001
Revision 2.1 JULY, 1998
AUTOMATIC NUMBER IDENTIFICATION (ANI)
(1300 Series Enhancement)
DESCRIPTION DATA
T/R : Transmitter PAD/Receiver PAD
+:Gain
- : Loss• YY=19 (DTI Pad) 
(1) Trunk Route No. (00-63) 
(2) 0 :
1 : Programmable PAD (See CM42)
2: 
3: 
4: 
5 :  Fixed PAD (See left table) 
6:
7:
• YY=20 (Sender Start Condition) 
(1) Trunk Route No. (00-63) 
(2) 00: Wink Start
Assign calling number sending method from 
the network to each trunk route.• YYY=129 (Calling No. Sending Method)
(1) Trunk Route No. (00-63)
(2) 0: Caller ID (Class SM)
1: T1-ANI
A
CM35
ENDCONNECTION 
PATTERNSPAD DATA OF DTI (dB)
DATA DATA DATA DATA
=4(T/R) =5(T/R) =6(T/R) =7(T/R)
Station-DTI
-3/-8 -3/-3 -3/-3 -3/-8
Tone-DTI
0/00/00/00/0
COT/LDT-DTI
0/00/00/00/0
ODT-DTI
+3/-30/0 0/0+3/-3
DTI-DTI
0/-6 0/0 0/-6 0/0 
						

							ND-45670 (E) CHAPTER 2
Addendum-001 Page 107
JULY, 1998 Revision 2.1
AUTOMATIC NUMBER IDENTIFICATION (ANI)
(1300 Series Enhancement)
2. MF Signaling Assignment
DESCRIPTION DATA
Assign a slot number to MF Receiver Trunk.
Note:The SENSE switch on the MF
Receiver Trunk gives the slot number.(1) Slot No. (04-15) 
(2) 08: MF Receiver Trunk (PN-4RST)
Assign MF Receiver Trunk Number to each 
MF Receiver Trunk.• YY=04 
(1) XX: MF Receiver Trunk No. (00-15) 
(2) XX
X 
Slot No. assigned by CM05
Circuit No. (0-3) 
Provide system with MF Signaling. (1) 52 (MF Signaling) 
(2) 0: To be provided
Assign calling number sending method from 
the network to the slot number assigned by 
CMOS (PN-4RSTB).• YY=07
(1) Slot No. (00-15)
(2) 0: Caller ID (Class SM)
1: T1-ANI
Provide required DID trunk route with MF 
Signaling.• YY=37 (MF Signaling Assignment)
(1) Trunk Route No. (00-63) 
(2) 0: Available
Assign MF PAD control level to the incoming 
signal.•Y=1 
(1) 0 (MF PAD Control level) 
(2) 0: –8.0 dBm 
1: –10.0 dBm 
2: –11.5 dBm 
3: –9.13 dBm 
4-7:  Not used
A
CM05
CM06
CM09
CMAA
CM35 START
CM31
INITIAL
INITIAL
INITIAL 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 08
Revision 2.0
AUTOMATIC NUMBER IDENTIFICATION (ANI 
1300 Series Enhancement)
DESCRIPTION DATA
Assign MF Receiver sensitive level. • Y=1 
(1) 1 (MF Receiver Sensitive level) 
(2) 00: –21 dBm 
14: –35 dBm 
15 : –36 dBm
(–1 dBm increments)
Assign MF Receiver to each circuit number 
(0-3) of the MF Receiver Trunk.
Note:AP Numbers 0-3 correspond to the
Slot Numbers assigned by CM05 (00-
15): 
AP Number 0: Slot Number X 
AP Number 1: Slot Number Y
AP Number 2: Slot Number Z 
AP Number 3: Slot Number W 
(X < Y < Z < W)
•Y=2 
(1) 0-3 (AP Number)
Note 
(2) 3 : All circuits assigned as Receiver
Assign supervisory timer of interdigit pause 
on incoming signal.•Y=B 
(1) 05 (Supervisory Timer of Interdigit Pause 
on Incoming Signal) 
(2) NONE : 24 sec. 
01: 1 sec. 
31: 31 sec.
Assign Busy/Idle information not to be sent to 
T1 network.• YY=48 (Busy/Idle Sending to T1 Net-
work) 
(1) Trunk Route No. (00-63) 
(2) 0 : Not available
A
CM31
CM35
END
INITIAL
~ ~
INITIAL
~
~ 
						

							ND-45670 (E) CHAPTER 2
Page 109
Revision 2.0
AUTOMATIC NUMBER IDENTIFICATION (ANI 
1300 Series Enhancement)
3. ANI Assignment
DESCRIPTION DATA
Assign requiring of ANI Signal from T1 
network when an incoming call terminates.(1) 472 
(2) 0: Available
Assign the Signal Pattern received from T1 
network.
• When the Signal Pattern from T1 network 
is FGD-Format: Assign the data to 
“NONE”. 
• When the Signal Pattern from T1 network 
is ANI-Format: Assign the data to 
“02”.
Note
•Y=3 
(1) 00 (Signal Pattern from T1 Network) 
(2) NONE : ANI + Called Number 
02: ANI
Assign the number of digits of Called Number 
received from T1 network.•Y=1 
(1) 2 (Number of Digits of Called Number) 
(2) NONE : NONE 
01: 1 digit 
31: 31 digits
Assign the signal kind of Called Number sent 
from T1 network.
Note:
• When the Signal Pattern from T1 network 
is FGD-Format: Assign the data to “1”. 
• When the Signal Pattern from T1 network 
is ANI-Format: Assign the data to “0”.•Y=A 
(1) 17 (Signal Kind of Called Number)  
Note
(2) 0: DP 
1: MF
Assign the ACK-WINK Signal to be sent to the 
DTI when the signal kind of Called Number 
received from T1 network is MF Signal.
Note:
• When the Signal Pattern from T1 network 
is FGD-Format: Assign the data to “0”. 
• When the Signal Pattern from T1 network 
is ANI-Format: Assign the data to “1”.•Y=A 
(1) 16 (Sending of ACK-WINK Signal on 
Receiving MF Signal)   
Note
(2) 0: To be sent 
1 :  Not to be sent
A
CM08
CM31 START
INITIALt
INITIALt
~
~
tt 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 10
Revision 2.0
AUTOMATIC NUMBER IDENTIFICATION (ANI 
1300 Series Enhancement)
DESCRIPTION DATA
Assign the ACK-WINK Signal to be sent to the 
DTI when the signal kind of Called Number 
received from T1 network is DP Signal.
Note:
• When the Signal Pattern from T1 network 
is FGD-Format: Assign the data to “1”. 
• When the Signal Pattern from T1 network 
is ANI-Format: Assign the data to “0”.•Y=A 
(1) 18 (Sending of ACK-WINK Signal on Re-
ceiving DP Signal)    
Note
(2) 0:  To be sent 
1 :  Not to be sent
Assign the number of digits of ANI received 
from T1 network.•Y=1 
(1) 3 (ANI Digits from T1 Network) 
(2) NONE : NONE 
01: 1 digit 
31: 31 digits
Assign the number of digits to be deleted from 
ANI, if required.
< An example of FGD Format >•Y=A 
(1) 14 (Number of Deleting Digits from ANI) 
(2) 00: No digit deletion 
01:  Leading one digit deletion 
10:  Leading 10 digits deletion 
11:  
No digits deletion
15 :
Assign whether ANI is sent to the OAI Terminal 
or not.(1) 462 (Sending ANI to OAI Terminal) 
(2) 0: To be sent 
1 :  Not to be sent
Assign whether ANI is sent to the SMDR 
Terminal or not.(1) 463 (Sending ANI to SMDR Terminal) 
(2) 0: To be sent 
1 :  Not to be sent
A
CM31
CM08
END
CM31
t
INITIALt
~
~
 Received digits:
 Key Pulse + XX + 1234567890 + Stop Pulse
ANI (10 digits)
Information digits (2 digits)
• 2 digits deletion
• Identification on the terminal: 
10 digits (ANI)
~~
~t
tt 
						

							ND-45670 (E) CHAPTER 2
Page 111
Revision 2.0
AUTOMATIC NUMBER IDENTIFICATION (ANI 
1300 Series Enhancement)
When the signal pattern of the Called Number sent from T1 network is as shown below, assign the following data,
if required.
Called Number = NPA + NNX + Called Station Number
Note:
FGD-Format and ANI-Format are:
HARDWARE REQUIRED
PN-24DTA card
PN-4RST card
DESCRIPTION DATA
Assign the Digit Addition/Deletion on the 
incoming calls.•
(1)
(2)YY=17 (Digit Addition/Deletion Assign-
ment) 
Trunk Route No. (00-63) 
00: “0” add 
09: “9” add 
10:  2 digit addition 
(CM50 YY=00 1st data: 0) 
11:  1 digits deletion 
12:  2 digits deletion 
15 :  Addition/deletion is not performed
Assign the access code for LCR Group 0-3. •
(1)
(2)Y=0-3 (Numbering Plan Group 0-3) 
X-XXXX (Access Code) 
A26:  LCR Group 0 
A27:  LCR Group 1 
A28:  LCR Group 2 
A29:  LCR Group 3
Assign an area code for Intra-Office 
Termination.•
(1)
(2)YYY=405-407 (Area Code Development
No. 5-7) 
X-XXXXX (Area Code, 1-5 digits) 
800: Intra-Office Termination
SIGNAL PATTERN CALLED NUMBER ANI
FGD-Format MF Signal MF Signal
ANI-Format DP Signal MF Signal
CM35
CM20
CM8ASTART
END
~
~
t 
						

							CHAPTER 2 ND-45670 (E)
Pag e 1 12
Revision 2.0
AUTOMATIC RECALL
PROGRAMMING
DESCRIPTION DATA
Specify the timing for AUTOMATIC 
RECALL. If no data is set, the following 
Automatic Recall timing is applied:
Attendant Recall - 31.2-33.6 seconds
Non exclusive Hold - 60-64 seconds
Exclusive Hold - 236-240 seconds
Transfer Recall - 24-28 seconds
Attendant Hold Recall - 31.2-33.6 seconds
Camp-On Recall - 24-32 seconds•  Y = 0
(1)  00: Attendant Recall
(2)  01-24: 2.4-124.8 sec. (Increments 01-14
are 2.4-sec. increments, and in-
crements 15-24 are 9.6-sec. incre-
ments)
(1)  05: Non exclusive Hold
(2)  01-98: 4-392 sec. in 4 sec. increments
99: Recall is not performed.
(1)  06: Exclusive Hold
(2)  01-98: 4-392 sec. in 4 sec. increments
99: Recall is not performed.
(1) 07: Transfer Recall
(2)  01-30: 4-120 sec. in 4 sec. increments
(1)  11: Attendant Hold Recall
(2)  01-24: 2.4-124.8 sec. (Increments 01-14
are 2.4-sec. increments, and in-
crements 15-24 are 9.6-sec. incre-
ments)
(1)  26: Camp-On Recall
(2)  01-15: 8-120 sec. in 8 sec. incrementsCM41 START
END 
						

							ND-45670 (E) CHAPTER 2
Page 113
Revision 2.0
BACKGROUND MUSIC (BGM)
PROGRAMMING
DESCRIPTION DATA
Assign BGM Interface Trunks (PN-4COT/
PN-TNT) to the required LENs.
Note:The PN-TNT Circuit No. must be
assigned to the first LEN (Level 0)
and/or the third LEN (Level 2) of
each LT slot.(1)  XXXX: 0000-0511 (LEN No. )
(2) D000-D255: PN-4COT/PN-TNT Circuit
No.
Assign the Service Restriction Class (A) to the 
required Multiline Terminals.• YY = 02
(1)  X-XXXX:Primary Extension No. of the
Multiline Terminal
(2) XX
 XX
*a: Service Restriction Class (A) (00-
15 )
Provide this feature to the Service Restriction 
Class (A) assigned by CM12.• YY = 32
(1)  Service Rest. Class (A) (00-15)
(2)  1 : Allowed
Assign the access code for this feature. •  Y = 0-3 (Numbering Plan Group 0-3)
(1)  X-XXX: Access code (66)
(2) 039: BGM
Assign a Trunk Route No. to the BGM 
Interface Trunk (PN-4COT/PN-TNT).• YY = 00
(1)  Trunk No. (000-255)
(2)  Trunk Route No. (00-63)
Assign the BGM interface to each trunk route. •  YY = 00
(1)  XX: Trunk Route No. 
(2) 05 (Interface with BGM Tone Source)
Assign a BGM program number to each trunk 
number connected to the External Tone 
Source.•  Y = 4
(1)  00-09 (BGM program No. 0-9)
(2)  DXXX: Trunk number connected to the
External Tone Source.
CM10 START
CM12
CM35
CM15
CM20
CM30
CM48
END
*a