Panasonic Kx Td500 User Manual

							Station Programming
User Manual71
Message Waiting (MESSAGE) Button (Assignment)
Allows you to assign a Flexible (CO, DSS) button as a Message Waiting (MESSAGE) button.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
PT
Press the desired Flexible(CO,
DSS) button you wish to assign
as the Message Waiting button,Dial 3Press STORE.
AUTO DIAL
STORE3
The STORE indicator lights.
The display shows the initial programming
mode. 
Message Waiting 
						

							Station Programming
72User Manual
One-Touch Dialing Button (Assignment)
Allows you to assign a Flexible (CO, DSS, PF) button as a One-Touch Dialing button.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
Conditions
The number can be an extension number, telephone number or a feature number. Up to 24 
digits can be stored in a One-Touch Dialing button.
To store the telephone number of an outside party, a line access code (9, or 801 through 848) 
must be stored as the leading digit.
You can store a number consisting of 25 digits or more by dividing it and assigning it in two 
One-Touch Dialing buttons. In this case, the line access code should be stored in the first 
button.
You can use 0 through 9,  , #, PAUSE, FLASH, CONF and INTERCOM for storing.
FLASH: hook flash
PAUSE: pause
CONF: — (hyphen)
INTERCOM: for secret dialing
#: for changing the dialing mode (Pulse to Tone)
KX-T7220 and KX-T7250 telephones do not have a PAUSE button. The PROGRAM 
button can be used instead of the PAUSE button while programming.
PT
Press the desired Flexible
(CO, DSS, PF) button you
wish to assign as a
One-Touch Dialing button.Dial 2.Press STORE. Enter the desired number
(extension number,
phone number, etc.).
desired number
AUTO DIAL
STORE2
The STORE indicator lights.
The display shows the initial
programming mode. 
Up to 24 digits can be stored.
To erase an incorrect entry, press the CLR (S2) button or the
TRANSFER (CLEAR)button.
(The TRANSFER button becomes the CLEAR button in the
Station Programming mode.)
CLR 
						

							Station Programming
User Manual73
Phantom Button (Assignment)
Allows you to assign a Flexible (CO) button as a Phantom button. 
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
Conditions
The phantom extension numbers must be assigned by System Programming  before assigning the Phantom button.
If you assign the Phantom button to one of the CO buttons (CO 13 through CO 24) on a PT 
with 24 CO buttons, such as KX-T7230, and change the telephone to a PT with 12 CO 
buttons, such as KX- T7235, you must re-program the setting because CO 13 through CO 
24 are not provided with the PT with 12 CO buttons. If you do not change the setting, the 
phantom extension call appears on the INTERCOM (ICM type PT) or PDN (DN type PT) 
button.
More than one identical Phantom button cannot be assigned on a single extension.


(-xxxx:Phantom extension number)
To erase an incorrect entry, press the CLR (S2) button or the
TRANSFER (CLEAR) button.
(The TRANSFER button becomes the CLEAR button in the Station
Programming mode.)
Phantom:
CLR
Phantom:xxxx
CLR
PT
Press the desired Flexible
(CO) button you wish to
assign as a Phantom button.Dial 72.Press STORE. Enter the phantom extension
number (3 or 4 digits).
phantom extension no.
AUTO DIAL
STORE (CO)72
The STORE indicator lights.
The display shows the initial
programming mode. 
						

							Station Programming
74User Manual
Primary Directory Number (PDN) Button (Assignment)
Allows you to assign a Flexible (CO) button as a PDN button.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
Conditions
A PDN button can be assigned to any one of the flexible CO buttons on a PT by Station, 
User or System Programming. Up to three PDN buttons can be assigned to any flexible CO 
button on a PT. However, the first PDN button should always be assigned to the CO 01 
button regardless of the number of the PDN buttons assigned.
PT
Press the desired Flexible (CO)
button you wish to assign as a
PDN button.Dial 74.Press STORE.
AUTO DIAL
(CO)
STORE47
The STORE indicator lights.
The display shows the initial programming mode. 
PDN 
						

							Station Programming
User Manual75
Release Button (Assignment)
Allows you to assign a Flexible (CO, DSS, PF) button as a Release button.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
SAVE Button (Assignment)
Allows you to assign a Flexible (CO, DSS, PF) button as a SAVE button.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
PT
Press the desired Flexible (CO,
DSS, PF) button you wish to
assign as the Release button.Dial 95.Press STORE.
AUTO DIAL
STORE95
The STORE indicator lights.
The display shows the initial programming mode. 
Release
PT
Press the desired Flexible (CO,
DSS, PF) button you wish to
assign as the SAVE button.Dial 5.Press STORE.
AUTO DIAL
STORE5
The STORE indicator lights.
The display shows the initial programming mode. 
Save 
						

							Station Programming
76User Manual
Secondary Directory Number (SDN) Button (Assignment)
Allows you to assign a Flexible (CO) button as an SDN button.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
Conditions
An SDN button should have its associated PDN button of another extension. This 
assignment is available for extensions on which at least one PDN button is already assigned 
(DN type PT). Otherwise, the SDN button dose not function.
Up to three different SDN buttons can be assigned to a PT.
Up to eight SDN buttons per PDN button can be assigned to eight different PTs respectively.


(-xxxx:extension number)
To erase an incorrect entry, press the CLR (S2) button or
the TRANSFER (CLEAR) button.
(The TRANSFER button becomes the CLEAR button in the
Station Programming mode.)
SDN—
CLR
SDN—xxxx
CLR
PT
Press the desired Flexible
(CO) button you wish to
assign as an SDN button.Dial 75.Press STORE. Enter the extension number
(3 or 4 digits) of the owner
extension.
extension no. of the 
owner extensionAUTO DIAL
(CO)
STORE57
The STORE indicator lights.
The display shows the initial
programming mode. 
						

							Station Programming
User Manual77
Single-CO (S-CO) Button (Assignment)
Allows you to assign a Flexible (CO, DSS) button as a Single-CO button.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
Conditions
You cannot assign the same CO line to more than one S-CO button on a PT.
You can assign the same CO line to an S-CO button, a G-CO button and an L-CO button 
respectively.
An S-CO button assigned to a DSS button is available for monitoring the call activity only, 
not available for making or receiving a call.
PT
Press the desired Flexible
(CO, DSS) button you wish
to assign as an S-CO button.Dial 0.Press STORE. Enter the trunk port physical
number.
trunk port physical number
AUTO DIAL
STORE0
The STORE indicator lights.
The display shows the initial
programming mode. 

(-xxxxx: trunk port physical number)
To erase an incorrect entry, press the CLR (S2) button or the
TRANSFER (CLEAR) button.
(The TRANSFER button becomes the CLEAR button in the Station
Programming mode.)
CO—
CLR
CLR CO—xxxxx 
						

							Station Programming
78User Manual
Tone Through Button (Assignment)
Allows you to assign a Flexible (CO, DSS) button as a Tone Through button.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
Features Guide References
1.12 Conversation Features
End-to-End DTMF Signaling (Tone Through)
PT
Press the desired Flexible (CO,
DSS) button you wish to assign
as the Tone Through button.Dial 78.Press STORE.
AUTO DIAL
STORE87

Tone Through
The STORE indicator lights.
The display shows the initial programming
mode. 
						

							Station Programming
User Manual79
Two-Way Record Button (Assignment)*1
Allows you to assign a Flexible (CO, DSS) button as a Two-Way Record button.
This allows you to record a conversation into your own mailbox.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
Conditions
You cannot enter a non-existent extension or floating directory number.*2
Please refer to Floating Station of Section 1.3 System Features in the Features Guide. 
You should use a voice mail extension number that has been assigned by System 
Programming. Please refer to Programming Guide References below.
Programming Guide References
1.5 VPS (DPT) Port Assignment
– [EXT No.1] DN
– [EXT No.1] Group No.
– [EXT No.2] DN
*1Available when the Digital Super Hybrid System is connected to a Digital Proprietary Telephone capable Panasonic Voice 
Processing System (one that supports Digital Proprietary Telephone [DPT] integration; e.g., KX-TVS100).
*2A Floating Directory Number (FDN) is a virtual extension number which appears to be an extension.


(-xxxx:VM extension number)
To erase an incorrect entry, press the CLR (S2) button or
the TRANSFER (CLEAR) button.
(The TRANSFER button becomes the CLEAR button in the Station
Programming mode.)
2 WAY-REC:
CLR
2  WAY-REC  :xxxx
CLR
PT
Press the desired Flexible
(CO, DSS) button you wish
to assign as the Two-Way
Record button.Dial 90.Press STORE. Enter the Voice Mail
extension number
(3 or 4 digits).
Voice Mail 
extension no.AUTO DIAL
STORE09
The STORE indicator lights.
The display shows the initial
programming mode. 
						

							Station Programming
80User Manual
– [EXT No.2] Group No.
Two-Way Transfer Button (Assignment)*1
Allows you to assign a Flexible (CO, DSS) button as a Two-Way Transfer button.
This allows you to record a conversation into a desired mailbox.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
Conditions
You cannot enter a non-existent extension or floating directory number.*2
Please refer to Floating Station of Section 1.3 System Features in the Features Guide.
You should use a voice mail extension number that has been assigned by System 
Programming. Please refer to Programming Guide References below.
Programming Guide References
1.5 VPS (DPT) Port Assignment
– [EXT No.1] DN
*1Available when the Digital Super Hybrid System is connected to a Digital Proprietary Telephone capable Panasonic Voice 
Processing System (one that supports Digital Proprietary Telephone [DPT] integration; e.g., KX-TVS100).
*2A Floating Directory Number (FDN) is a virtual extension number which appears to be an extension.


(-xxxx:VM extension number)
To erase an incorrect entry, press the CLR (S2) button or the
TRANSFER (CLEAR) button.
(The TRANSFER button becomes the CLEAR button in the Station
Programming mode.)
2 WAY-TRANS:
CLR
2 WAY-TRANS:xxxx
CLR
PT
Press the desired Flexible
(CO, DSS) button you wish
to assign as the Two-Way
Transfer button.Dial 91.Press STORE. Enter the Voice Mail
extension number
(3 or 4 digits).
Voice Mail 
extension no.AUTO DIAL
STORE19
The STORE indicator lights.
The display shows the initial
programming mode.