Panasonic Kx Td500 User Manual

							Station Features and Operation (PT/SLT)
User Manual361
4.3.66 Redial
Redial feature can be categorized as the following two types.
Redialing the last outside phone number you dialed (Last Number Redial)
Saving the outside phone number for redialing (Saved Number Redial)
Dialing
Type Description
Last NumberSaves the last telephone number dialed to a CO line and allows the extension 
user to dial the same number again.
Saved NumberAllows the PT user to save a telephone number while in conversation on a CO 
line or while hearing a busy tone and redial the number afterwards. The saved 
number can be redialed until another number is stored.
SLTPT
Lift the handset. Dial #.Press REDIAL.Lift the handset or press
SP-PHONE/MONITOR.
REDIAL
or
Dial #.
PT
Press SAVE (flexible button). Press STORE.
During a conversation or while hearing a busy tone;
AUTO DIAL
STORE
(SAVE)
PT
Press SAVE (flexible button).
(SAVE)
Lift the handset or press
SP-PHONE/MONITOR. 
						

							Station Features and Operation (PT/SLT)
362User Manual
Conditions
[General]
Up to 24 digits (excluding the CO line access code) can be stored and redialed.
 , #, PAUSE, and INTERCOM (for secret dialing) are counted as one digit.
If Full One-Touch Dialing feature is enabled at the extension, there is no need to go off-
hook, before pressing the REDIAL or SAVE button.
[Last Number]
The memorized telephone number is replaced by a new one if at least one digit sent to a CO 
line is dialed. Dialing a CO line access code alone does not change the memorized number.

If you hear a busy tone when attempting to redial, select another line and press the REDIAL 
button.
[Saved Number]
SAVE button
If the SAVE button is not provided on your PT, it is possible to assign a flexible button (CO, 
DSS, PF) to be the SAVE button by Station, User or System Programming.
Programming Guide References
2.3 Numbering Plan
– Redial
4.3 Extension Line
– CO Key
– PF Key
4.4 DSS Console
– DSS Key
– PF Key
Features Guide References
1.7 Dialing Features
Redial
1.16 Button Features
Button, Flexible
User Manual References
2.2.3 Flexible Button Assignment 
						

							Station Features and Operation (PT/SLT)
User Manual363
2.2.4 Full One-Touch Dialing Assignment
3.2.5 [005] Flexible CO Button Assignment 
						

							Station Features and Operation (PT/SLT)
364User Manual
4.3.67 Released Link Operation 
When Released Link Operation is enabled by System Programming, you will be automatically 
released from a call (extension, outside) after transferring it to the destination, if the destination 
extension is idle. This feature simplifies the transfer operation by eliminating the need for 
going on-hook or pressing the RELEASE button after transferring the call.
This feature is convenient for extension users, such as Operators, who handle a large volume 
of calls. 
Conditions
Class of Service
Class of Service programming determines the extension that can perform this feature.
Released Link Operation functions when transferring a call to the ordinary extensions or 
floating extensions (extension group, incoming group, phantom extensions).
If the destination party is busy, Camp-on Transfer is set by going on-hook.

The SLT extension user cannot establish a conference call, if Released Link Operation is 
enabled by System Programming.
Programming Guide References
2.4 Class of Service (COS)
– Released Link Operation
Features Guide References
1.3 System Features
Released Link Operation
PT and SLT
For SLT For PT
TRANSFER
For PT: Press TRANSFER.
For SLT:  Flash the switchhook.Confirmation tone
and dial tone.
extension no.
Dial the destination
extension number
(3 or 4 digits).
The other party is placed on
consultation hold.
Ringing starts at the destination extension(s).
The call is transferred.
During a conversation; 
						

							Station Features and Operation (PT/SLT)
User Manual365
1.11 Transferring Features
Call Transfer
User Manual References
None 
						

							Station Features and Operation (PT/SLT)
366User Manual
4.3.68 Ringing Transfer
Allows a DN type PT user to transfer a call on the SDN button (flexible button) to the owner 
extension of the SDN which has the PDN button associated with it simply by pressing the SDN 
button.
Ringing transfer can be done either with or without announcement.
Screened Call Transfer
Unscreened Call Transfer
PT (DN type)
Announce. Wait for
an answer.
During a conversation on an SDN button;
Hang up or 
press
SP-PHONE.Press SDN
(flexible button).Ringback tone
The call is transferred
to the PDN owner.
(SDN)
PT (DN type)
During a conversation on an SDN button;
Hang up or
press
SP-PHONE.Press SDN
(flexible button).Ringback tone
The call is transferred.
(SDN) 
						

							Station Features and Operation (PT/SLT)
User Manual367
Conditions

If the owner extension is in the Station or User Programming mode, Ringing Transfer does 
not function.
FWD/DND Override
The call transferred by this features rings the PDN owner extension even if Call Forwarding 
or Do Not Disturb feature is assigned on it.

A call made by this feature rings the destination PDN button immediately even if delayed 
ringing or no ring is set on that PDN button. Please refer to Section 2.2.9 PDN/SDN 
Button Delayed Ringing Assignment.
Programming Guide References
4.3 Extension Line
– CO Key
Features Guide References
1.11 Transferring Features
Ringing Transfer
User Manual References
2.2.3 Flexible Button Assignment
2.2.9 PDN/SDN Button Delayed Ringing Assignment
3.2.5 [005] Flexible CO Button Assignment 
						

							Station Features and Operation (PT/SLT)
368User Manual
4.3.69 Secret Busy Override
You can interrupt an existing call (either between two inside parties or between an inside 
party and an outside party) without informing the other party.
Some extensions may be restricted from performing this function.
To interrupt an existing call 
To change to the three-party conference call
7230 / 7235 / 7433 / 7436
Dial 2.
If you hear a busy tone after making an intercom call;
2
Over
S1
S2S3
If you hear a busy tone after making an intercom call; 
Press Over (S2).
PT and SLT
Lift the handset or press
SP-PHONE/MONITOR.
Lift the handset or press
SP-PHONE/MONITOR.
Party A and Party B in conversation do not know 
that their conversation is being monitored by Party C.
Party A and Party B in conversation do not know 
that their conversation is being monitored by Party C.
PT
Press the ICM or DN
corresponding to the
desired caller.
A three-party conference
is now established. or(ICM)(DN)
When “Secret Busy Override” is executed. 
						

							Station Features and Operation (PT/SLT)
User Manual369
Conditions
Class of Service (COS) programming
COS programming  determines the extension users who can 
perform this feature.
This feature does not work if Executive Busy Override Deny or Data Line Security is 
set at either one of two extensions or both of them. 
Party A and Party B are in conversation.
This feature works as follows so that both party A and party B do not know that their 
conversation is being monitored by Party C:
— The display and LED indicator at party A and party B show the status of a 2-party
conversation.
— A confirmation tone is not sent to either party A or party B even if it is enabled by System
 Programming.
— The speech path from the party C to the party A and party B is not connected.
If either one of two extensions or both of them is released from the call to perform other 
operations such as making a call or placing it on hold, this feature is terminated and then a 
reorder tone is sent to the calling extension.
Programming Guide References
2.3 Numbering Plan
– Data Line Security Set / Cancel
– Executive Busy Override Deny Set / Cancel
2.4 Class of Service (COS)
– Busy Override
– Busy Override Deny
– Secret Busy Override
2.8 System Option
– Confirmation tone for Override, Barge-in, Conference and Privacy Release
Features Guide References
1.6 Originating Features
Secret Busy Override
1.9 Answering Features
Executive Busy Override Deny
1.12 Conversation Features
Data Line Security
User Manual References
None 
						

							Station Features and Operation (PT/SLT)
370User Manual
4.3.70 Secret Dialing
Allows you to conceal all or part(s) of a System Speed Dialing or One-Touch Dialing 
number assigned to a flexible button on your PT and DSS Console which normally appears on 
the display. Additionally, KX-T7431, KX-T7433, KX-T7436 and KX-T7235 Model 
Telephones are capable of Secret Dialing for Station Speed Dialing numbers.
Conditions

The secret code, [ or ] (pressing the INTERCOM button), are counted as one digit.

You can conceal one or more parts of a telephone number.

If the phone number 9-1-[123]-456-7890 has been stored, the display shows the following 
when the call is made:
Programming Guide References
5.2 System Speed Dialing
Features Guide References
1.3 System Features
Secret Dialing
1.7 Dialing Features
One-Touch Dialing
System Speed Dialing
1.17 Display Features
Call Directory
PT
Press INTERCOM before and after the part you wish to conceal.
When storing the phone number;
INTERCOM

— “123” is not shown on the display when you dial.
9-1-[123]...
-1-...
-456-7890