Panasonic Kx Td500 User Manual

							Station Programming
User Manual91
Prime Line Preference — Incoming (Assignment)
You are connected to a call on the line assigned as the prime line automatically, when you go 
off-hook to answer a call.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
Note
If your PT is DN type, then you cannot select ICM.
PT
Dial 3. Dial 2.Press STORE. Press the desired line access
button. 
(Selection)
ICM, S-CO, G-CO, L-CO, PDN, SDN
32
AUTO DIAL
STORE
The STORE indicator lights.
The display shows the initial
programming mode. The display shows the current status.

(   When ICM is selected)
Pref.In :ICM 
						

							Station Programming
92User Manual
2.2.12 Preferred Line Assignment — Outgoing
Allows you to select the desired outgoing line preference to originate calls from the following 
three line preferences:
a) No Line Preference
b)Idle Line Preference
c)Prime Line Preference (INTERCOM) (— default*1)
Follow the programming procedure according to your selection.
Note
If Idle Line Preference, No Line Preference or Prime Line Preference (S-CO, G-
CO or L-CO) is selected, it is not possible to access any PT features after going off-
hook. To access these PT features, press the INTERCOM (ICM type PT) or PDN (DN 
type PT) button before or after going off-hook.
No Line Preference — Outgoing (Assignment)
When you go off-hook to make a call, you are not connected to any line. You must choose the 
line.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
*1If PT is DN type, then the default is PDN.
PT
Dial 1.Press STORE. Dial 1.
11
AUTO DIAL
STORE
The STORE indicator lights.
The display shows the initial
programming mode.The display shows the current
status.

Pref.Out:No 
						

							Station Programming
User Manual93
Idle Line Preference — Outgoing (Assignment)
When you go off-hook to make a call, you are connected to an idle line automatically.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
PT
Dial 2.Press STORE. Dial 1.
12
AUTO DIAL
STORE
The STORE indicator lights.
The display shows the initial
programming mode.The display shows the current
status.

Pref.Out:Idle 
						

							Station Programming
94User Manual
Prime Line Preference — Outgoing (Assignment)
When you go off-hook to make a call, you are connected to a line assigned as the prime line 
automatically.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
Note
If your PT is DN type, then you cannot select ICM.
PT
Dial 3. Dial 1.Press STORE. Press the desired line access
button.
(Selection)
ICM, S-CO, G-CO, L-CO, PDN, SDN
13
AUTO DIAL
STORE
  The STORE indicator lights.
  The display shows the initial
programming mode.   The display shows the current status.

(   When ICM is selected)
Pref.Out:ICM 
						

							Station Programming
User Manual95
2.2.13 Ringing Tone Selection for CO Buttons
Allows you to assign a ringer frequency to each CO (S-CO, G-CO, L-CO) or DN (PDN, SDN) 
button.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
Conditions
The default is Ringing Tone Type 2.
This feature applies to the following line access buttons:
S-CO, G-CO, L-CO, PDN, SDN
Press CO, PDN or SDN
which you wish to
change the ringing tone.Press STORE. Press the same CO,PDN
or SDN again.Enter the tone type number
(1 through 8). 
tone type no.AUTO DIAL
STORE
The display shows the current
status.
The display shows the selected tone type number and you hear
the selected tone until the STORE button is pressed.

(-x:tone type number)
If you want to change the tone type, enter another tone type
number.
Tone Type-X
DPT
The STORE indicator lights.
The display shows the initial
programming mode. 
						

							Station Programming
96User Manual
2.2.14 Ringing Tone Selection for INTERCOM Button
Allows you to assign a ringer frequency to the INTERCOM button.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
Conditions
The default is Ringing Tone Type 3.
The display shows the current
status
The display shows the selected tone type number and you hear
the selected tone until the STORE button is pressed.

(-x:tone type number)
If you want to change the tone type, enter another tone type
number.
Tone Type-X
DPT
Press INTERCOM.
Press STORE. Press INTERCOM again.Enter the tone type number
(1 through 8).
tone type no.INTERCOMINTERCOMAUTO DIAL
STORE
The STORE indicator lights.
The display shows the initial
programming mode. 
						

							Station Programming
User Manual97
2.2.15 Self-Extension Number Confirmation
Allows you to display your extension port physical number and extension number.
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9]. 
— To exit the Station Programming mode: Press [PROGRAM].
Dial 6.
Press HOLD (END).
6HOLDPT
The display shows the initial programming
mode. 
extension port
physical number
10101EXT1001 
						

							Station Programming
98User Manual
2.2.16 Station Programming Data Default Set
Allows you to return each of the following items assigned by Station Programming to their 
default settings.
a)Bilingual Display Selection (default: English)
b)Call Waiting Tone Type Assignment (default: Tone 1)
c)Full One-Touch Dialing Assignment (default: On)
d)Handset/Headset Selection (default: Handset)
e)Initial Display Selection (default: Caller ID)
f)Intercom Alert Assignment (default: Tone Call)
g)Live Call Screen Mode Set (default: Hands-free)
h)Preferred Line Preference — Incoming (default: Ringing Line)
i)Preferred Line Preference — Outgoing (default: INTERCOM Line)
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
PT
Press STORE. Dial #.
AUTO DIAL
STORE
The STORE indicator lights.
The display shows the initial programming
mode. 
Clear Ready? 
						

							Station Programming
User Manual99
2.2.17 Station Speed Dialing Number/Name Assignment [KX-
T7235/KX-T7431/KX-T7433/KX-T7436 only]
Allows you to assign frequently dialed numbers and names to each Function button on your PT.
For KX-T7235 and KX-T7436 users
To store a number
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
7235/7436
Press STORE. Enter the desired number
(extension number,
phone number, etc.).
desired number
AUTO DIAL
STORE
PT-PGM ModeF5
F4
F3
F2
F1
F10
F9
F8
F7
F6
Press Function (F1-F10).
The STORE indicator lights.
The display shows the initial
programming mode.
Up to 24 digits, consisting of 0 through 9,     , #, FLASH, PAUSE, INTERCOM,
(“[” or “]” : secret) and CONF (-:hyphen), can be stored.
To store the telephone number of an outside party, the line access code (9 or 801
through 848) must be stored as the leading digit.
To erase the line, press the CLR (S2) button.
To store a name, press the NEXT(S3) button and go to step 3 in “To store a name”
as described in the following procedure.
The STORE indicator light turns off.
The display shows the current status.
(If nothing is stored, “Not Stored” is displayed.)

(– Outside number, 123-4567,
      is now programmed.)9-123-4567
      CLR  NEXT 
						

							Station Programming
100User Manual
To store a name
— Be sure that you are in the Station Programming mode: Press [PROGRAM] [9] [9].
— To exit the Station Programming mode: Press [PROGRAM].
* Please refer to Combination Table 1 and Combination Table 2 in Section 
2.2.17 Station Speed Dialing Number/Name Assignment [KX-T7235/KX-T7431/KX-
T7433/KX-T7436 only] for information on how to enter each character.
Conditions
Up to 10 characters can be stored.
The display shows the current status.
(If nothing is stored, Not Stored is displayed.)

(
- Name is now
programmed.)
7235/7436
Press STORE. Press Function (F1-F10). Press NEXT (S3).
Enter the name.*
desired name
AUTO DIAL
STORE
S 1
S 2
S 3
NEXT
PT-PGM ModeF5
F4
F3
F2
F1
F10
F9
F8
F7
F6
The STORE indicator lights.
The display shows the initial
programming mode. The STORE indicator light turns off.
The display shows the current status.
Bob Graham
CLR NEXT