Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation And Test For Multi-Carrier Cabinets Manual

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-147 Installing an Integrated Channel Service Unit (ICSU) Module 
5
nCord DW8A-DE
4-p air mod ular c ord  to alarm c ontac ts
nDS1 circuit pack
The b asic  ICSU req uires a TN474E or TN777D or later suffix. The 
enhanc ed  integ rated  c hannel servic e unit req uires a TN474F or TN777E or 
later suffix.
Installing the 120A CSU
See Figure 5-52. 
Figure 5-52. 120A Channel Service Unit Module
!CAUTION:
Do not p lug  the 120A into any c irc uit p ac k other than a TN474F or TN777E 
or later release/vintag e. Do not c onnec t the 120A to any interfac e other than 
a network smart jac k.
Be sure the DS1 c irc uit p ac k is set for 24-c hannel op eration (1.544 Mbp s). 
The 120A d oes not op erate with the 32-c hannel interfac e. A switc h on the 
c irc uit p ac k or ad ministration sets this op tion. 
1. Rear of c arrier c ontaining  DS1 c irc uit p ac k
2. 120A CSU
3. 4-p air c ord  to network interfac e (H600-383)4. DW8A-DE 4-p air c ord  to alarm c ontac ts (op tional)
5. To 25-p air c onnec tor on rear of c arrier c ontaining  
DS1 circ uit pac k
16 17 18 19 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01AU X
icsupic RBP 032896 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-148 Installing an Integrated Channel Service Unit (ICSU) Module 
5
!CAUTION:
Always wear an anti-static  wrist strap when installing  a 120A mod ule. Do 
not touc h the external alarm c able when it is c onnec ted  to the 120A. Static  
d isc harg e c an d amag e c onnec tor terminals and  relays. 
1. Unp lug  the DS1 c irc uit p ac k from its slot.
2. Install a 4C retainer in the 50-p in p lug  assoc iated  with the DS1 c irc uit p ac k 
slot.
3.Plug  the 120A’s 25-p air c onnec tor d irec tly into the p lug  assoc iated  with 
the DS1 c irc uit p ac k slot. 
4. Sec ure the 4C retainer around  the 120A.
5. Attac h the sup p lied  H600-383 c able to the 120A and to the network smart 
jac k. 
This c ab le is d irec tional. To determine the end  that c onnec ts to the 120A, 
p erform a c ontinuity test b etween pins 3 and  7. The end  with this 
c ontinuity is the 120A end . The shield  is g round ed  only at the 120A end .
 Use the c ab le p rovid ed . If c ab ling  other than that p rovided  with the 120A 
is used , ob serve the following  g uid elines:
nUse 24-g aug e wire that p rovid es ind ividually shield ed , twisted  p airs 
for transmit and  rec eive sig nals. Use the c ab le b etween the 
network interfac e and  the 120A. Ground  the shield s of this c able 
only at the 120A end to avoid  g round  loop s.
nCab ling  b etween the network interfac e and  120A c an have no 
bridge taps.
nIf using  stand ard  house riser c ab le for c onnec tions b etween the 
network interfac e and  the 120A, maintain a 100-p air sep aration 
b etween the rec eive and  transmit twisted  p airs.
nIf using  stand ard  house riser c ab le for c onnec tions b etween the 
network interfac e and  the 120A, allow no more than 2 c ross 
c onnec ts to 110-typ e c ross c onnec t bloc ks.
nNever use quad  c ab le (untwisted  two pair telep hone c ab le) in a 
DS1 line.
nAvoid  mixing  wires of d ifferent g aug es in a DS1 line.
6. If using  external alarm eq uip ment, attac h the sup p lied  DW8 c ab le to the 
120A and  the external eq uip ment. The maximum length of this c ab le 
d ep end s on the alarm eq uip ment.
7. If a TN474F is used , make sure the c irc uit p ac k is set for 24-c hannel 
op eration. Set the switc h on the c irc uit p ac k as shown in Fig ure 5-52
.
8. From the DS1 c irc uit-p ac k form of the system ad ministration c onsole, set 
the line c omp ensation field  to 0-133 feet (40.6 m). 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-149 Installing an Integrated Channel Service Unit (ICSU) Module 
5
9. Reset the 120A b y reseating  the DS1 c irc uit p ac k.
When you reinsert the DS1 c irc uit p ac k after installing  a 120A CSU the 
120A resets. The DS1 c irc uit p ac k initializes and  tests the 120A. When 
initialization and  testing  is c omp lete, the g reen LED goes off. If the RED 
indic ator is OFF after the test, the ICSU is working .
10. If the c irc uits d o not p ass the self test, troub leshoot the 120A as instruc ted  
in Integ rated  CSU Mod ule Installation and  Op eration, 555-230-193.
Table 5-28
 provides the H600-383 cable pinouts. Table 5-29 provides the cable 
lengths for each cable group number.
Table 5-28. H600-383 cable Pin Assignments
Pin ColorChannel Service 
Unit DesignationNetwork 
Designation Function
1BK Line in 0 R1 RCV
2 Y Line in 1 T1
3 Shield
4 R Line out 0 R XMT
5 G Line out 1 T
7 Shield
7 Not assigned
8 Not assigned
Table 5-29. H600-383 cable Lengths by Group Number
Group Length Group Length
1 25 ft (7.7 m) 5 125 ft (38.1 m)
2 50 ft (15.2 m) 7 200 ft (71 m)
3 75 ft (22.9 m) 7 400 ft (122 m)
4 100 ft (30.5 m) 8 750 ft (198.1 m) 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-150 Installing a 3150/3170 Channel Service Unit 
5
Installing a 3150/3170 
Channel Service Unit
1. Install the CSU as shown in Figure 5-13. For some installations (such as a 
DS1 c onverter), use a Y-c ab le to c onnec t the DEFINITY System to the 
q uad  c ab le. Tab le 5-13
 shows the Y-c ab le leng ths. Be sure to lab el all 
cables. 
Figure 5-13
 shows a typ ic al c onnec tion from the H600-348 Quad  c ab le to 
the CSU, through the H600-307 network c ab le, and  to the network 
interfac e throug h the smart jac ks. The q uad  c ab le p rovid es up  to four 
c onnec tions using a 15-pin c onnec tor that p lug s into the DTE jac k on eac h 
CSU. The H600-348 q uad  c ab le may req uire an ad ap ter c ab le.
Figure 5-53. 3150/3170 Channel Service Unit Connections 1. H600-348 q uad  c ab le
2.15-p in male “ D”  c onnec tors (to DTE jac ks on CSU)
3. Channel servic e unit (CSU)
4. H600-383 c ab le (RJ-48C to RJ-48C)
5. Network interfac e6. Smart jac k (if p rovid ed )
7. Cab le A
8. Cab le B
9. Cab le C
10. Cab le D
3150csu RBP 062696
POWERAUX PORT COM PORT MODEM
DTENETWORK
POWERAUX PO RT C OM PORT M OD EM
DTENETWORK
POWERAUX PORT COM PORT MODEM
DTENETWORK
POWERAUX PORT COM PORT MODEM
DTENETWORK 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-151 Installing a 3150/3170 Channel Service Unit 
5
Figure 5-54. DS1 Converter Connections Using Double-Headed cable
1. Port c arrier
2. DS1 c onverter c onnec tor
3. 50-p air female c onnec tor to DEFINITY 
EC S
4.14-in. (35.57 c m) “Y” cable5. 50-Pin Male/50-p in female 
double-headed  connector cable
6. Quad  c ab le (with 50-p in male c onnec tor) 
c onnec ts to the c hannel servic e unit.
Table 5-30. “Y” cable Lengths (DS1 converter Only)
Length 
(in/cm) Description Comcode
14/35.5  TN1754 to adjac ent exp ansion interfac e c irc uit p ac k or 
TN573B switc h nod e interfac e c irc uit p ac k in same c arrier 847245750
70/177.8 TN1754 to exp ansion interfac e c irc uit p ac k or switc h nod e 
interfac e in another c arrier847245778
14/35.5 TN1754 to fib er op tic  transc eiver (DC-p owered  c ab inets only). 
This c ab le is for interc ab inet c ab ling only.847245777
14/35.5 TN1754 to adjac ent TN570/B/C exp ansion interfac e c irc uit 
pack 847747741
cydf010 RPY 090597
20 1916 17 18 15 14 13 12 1110
09 08 07 06 05 04 03 02 01 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-152 Connector and Cable Diagrams (Pinout Charts) 
5
Connector and Cable Diagrams 
(Pinout Charts)
See Table 5-31 for lead designations. The circuit packs and auxiliary equipment 
are classified as shown in the tables at the end of this chapter.
`
Table 5-31. Lead and Color Designations 
Cross-Connect Pin  Color Amphenol Pin  Backplane Pin
1W-BL26 102
2 BL-W 01 002
3W-O27 103
4O-W02 003
5W-G28 104
6G-W03 004
7W-BR29 105
8BR-W04 005
9W-SL30 106
10 SL-W 05 006
11 R-BL 31 107
12 BL-R 06 007
13 R-O 32 108
14 O-R 07 008
15 R-G 33 109
16 G-R 08 009
17 R-BR 34 110
18 BR-R 09 010
19 R-SL 35 111
20 SL-R 10 011
21 BK-BL 36 112
22 BL-BK 11 012
23 BK-O 37 113
24 O-BK 12 013
25 BK-G 38 302
26 G-BK 13 202
27 BK-BR 39 303
28 BR-BK 14 203
29 BK-SL 40 304
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-153 Connector and Cable Diagrams (Pinout Charts) 
5
30 SL-BK 15 204
31 Y-BL 41 305
32 BL-Y 16 205
33 Y-O 42 306
34 O-Y 17 206
35 Y-G 43 307
36 G-Y 18 207
37 Y-BR 44 308
38 BR-Y 19 208
39 Y- SL 45 3 09
40 SL-Y 20 209
41 V-BL 46 310
42 BL-V 21 210
43 V-O 47 311
44 O-V 22 211
45 V-G 48 312
46 G-V 23 212
47 V-BR 49 313
48 BR-V 24 213
49 V- SL 50 3 00
50 SL-V 25 200
Table 5-31. Lead and Color Designations  — Continued
Cross-Connect Pin  Color Amphenol Pin  Backplane Pin
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-154 Connector and Cable Diagrams (Pinout Charts) 
5
Table 5-32 shows the pinouts for the TN2185 ISDN-BRI 4-wire S Interface. 
Table 5-32. TN2185 ISDNBRI — 4-Wire S Interface Pinout
Port Signal Cross-Connect Pin  Color Amphenol  Pin  Backplane  Pin
1 TXT.1 1 W-BL 26 102
TXR.1 2 BL-W 01 002
PXT.1 3 W-O 27 103
PXR.1 4 O-W 02 003
2 TXT.2 5 W-G 28 104
TXR.2 6 G-W 03 004
PXT. 2 7 W-B R 2 9 1 0 5
PXR. 2 8 BR- W 0 4 0 0 5
3 TXT.3 9 W-SL 30 106
TXR.3 10 SL-W 05 006
PXT.3 11 R-BL 31 107
PXR.3 12 BL-R 06 007
4 TXT.4 13 R-O 32 108
TXR.4 14 O-R 07 008
PXT. 4 1 5 R-G 3 3 1 0 9
PXR. 4 1 6 G - R 0 8 0 0 9
5 TXT.5 17 R-BR 34 110
TXR.5 18 BR-R 09 010
PXT. 5 1 9 R- SL 3 5 1 1 1
PXR. 5 2 0 SL - R 1 0 0 1 1
6 TXT.6 21 BK-BL 36 112
TXR.6 22 BL-BK 11 012
PXT.6 23 BK-O 37 113
PXR.6 24 O-BK 12 013
7 TXT.7 25 BK-G 38 302
TXR.7 26 G-BK 13 202
PXT. 7 2 7 B K- B R 3 9 3 0 3
PXR. 7 2 8 B R- B K 1 4 2 0 3
8 TXT.8 29 BK-SL 40 304
TXR.8 30 SL-BK 15 204
PXT. 8 3 1 Y- BL 4 1 3 0 5
PXR.8 32 BL-Y 16 205 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-155 Connector and Cable Diagrams (Pinout Charts) 
5
Table 5-33 shows the pinouts for the TN2198 ISDN-BRI 2-wire U Interface.
* 
Pins 25 and 50 are grounded by the backplane.
Table 5-33. TN2198 ISDN-BRI — 2-Wire U Interface Pinout
Port Signal Cross-Connect 
Pin ColorAmphenol 
Pin Backplane Pin
1T.1 1 W-BL 26 102
R.1 2 BL- W 0 1 00 2
2T.2 3 W-O 27 103
R.2 4 O - W 0 2 00 3
3T.3 5 W-G 28 104
R.3 6 G - W 0 3 00 4
4T.4 7 W-BR 29 105
R.4 8 BR- W 0 4 00 5
5T.5 9 W-SL 30 106
R.5 10 SL- W 0 5 00 6
6 T.6 11 R-BL 31 107
R.6 12 BL-R 06 007
7T.7 13 R-O 32 108
R.7 14 O - R 0 7 00 8
8T.8 15 R-G 33 109
R.8 16 G - R 0 8 00 9
9 T.9 17 R-BR 34 110
R.918BR-R09 010
10 T.10 19 R-SL 35 111
R.10 20 SL-R 10 011
11 T.11 21 BK-BL 36 112
R.11 22 BL-BK 11 012
12 T.12 23 BK-O 37 113
R.12 24 O-BK 12 013 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-156 Connector and Cable Diagrams (Pinout Charts) 
5
Table 5-34. Port Circuit Pack Lead Designations 
Cross- 
Connect 
PinTN742/B
TN747B
TN753 
TN769 
TN2147 
TN465TN754
TN726TN760/B
TN760C 
TN760D
TN2209 TN762/BTN763 
TN763B
TN763C TN735TN767B
TN464ETN746/B 
TN2183
TN793
TN2793 TN2224
1 T.1 T.1 T.1 T.1 T.1 C_5 T.1 T.1
2 R.1 R.1 R.1 R.1 R.1 R.1 R.1
3 TXT. 1 T1 . 1 TXT. 1 SZ . 1 B T. 1 C _EN A B T. 2 T. 2
4 TXR.1 R1.1 TXR.1 SZ1.1 BR.1 R.2 R.2
5 PXT. 1 E. 1 PXT. 1 S.1 L T.1 C_SYNC* T.3 T.3
6 PXR.1 M.1 PXR.1 S1.1 LR.1 R.3 R.3
7 T.2 T.2 T.2 T.2 T.2 C2D-DATA T.4 T.4
8 R.2 R.2 R.2 R.2 R.2 RDATA* R.4 R.4
9 TXT. 2 T1 . 2 TXT. 2 SZ . 2 B T. 2 TD A TA * T. 5
10 TXR.2 R1.2 TXR.2 SZ1 .2 B R.2 TRSYSN C R.5
11 PXT.2 E.2 PXT.2 S.2 LT.2 GRD T.6
12 PXR.2 M.2 PXR.2 S1.2 L R. 2 SC L K* R.6
13 T.3 T.3 T.3 T.3 T.3 T.7
14 R.3 R.3 R.3 R.3 R.3 R.7
1 5 TXT. 3 T1 . 3 TXT. 3 SZ . 3 B T. 3 T. 8
16 TXR.3 R1.3 TXR.3 SZ1 .3 B R.3 PA H ER* R.8
1 7 PXT. 3 E. 3 PXT. 3 S. 3 L T. 3 T. 5 T. 9
18 PXR.3 M.3 PXR.3 S1.3 LR.3 C_48V R.5 R.9
19 T.4 T.4 T.4 T.4 T.4 T.6 T.10
20 R.4 R.4 R.4 R.4 R.4 R.6 R.10
2 1 TXT. 4 T1 . 4 TXT. 4 SZ . 4 B T. 4 C _P2 SC L K T. 7 T. 1 1
22 TXR.4 R1.4 TXR.4 SZ1.4 BR.4 LI
 (RX) R.7 R.11
2 3 PXT. 4 E. 4 PXT. 4 S. 4 L T. 4 L O *  ( TX) T. 8 T. 1 2
24 PXR.4 M.4 PX4.4 S1.4 LR.4 LBACK1 R.8 R.12
2 5 T. 5 T. 5 T. 5 T. 5 T. 5 G N D T. 9 T. 1 3
26 R.5 R.5 R.5 R.5 R.5 C _5V R.9 R.13
2 7 TXT. 5 T1 . 5 TXT. 5 SZ . 5 B T. 5 T. 1 0 T. 1 4
28 TXR.5 R1.5 TXR.5 SZ1.5 BR.5 R.10 R.14
2 9 PXT. 5 E. 5 PXT. 5 S. 5 L T. 5 T. 1 1 T. 1 5
30 PXR.5 M.5 PXR.5 S1.5 L R. 5 C _RST R.11 R.15
31 T.6 T.6 T.6 T.6 T.6 T.12 T.16
32 R.6 R.6 R.6 R.6 R.6 R.12 R.16
3 3 TXT. 6 T1 . 6 TXT. 6 SZ . 6 B T. 6 RD A TA T. 1 7
34 TXR.6 R1.6 TXR.6 SZ1 .6 B R.6 TD A TA R.17
3 5 PXT. 6 E. 6 PXT. 6 S. 6 L T. 6 TRSYN C T. 1 8
36 PXR.6 M.6 PXR.6 S1.6 L R. 6 GRD R.18
37 T.7 T.7 T.7 T.7 T.7 SCLK T.19
38 R.7 R.7 R.7 R.7 R.7 R.19
Continued on next page