Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation And Test For Multi-Carrier Cabinets Manual

							Install and Connect Cabinets 
1-1 Unpack and Inspect Cabinets 
1
DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
1
Install and Connect Cabinets
This c hapter d isc usses installation of Multic arrier Cab inets only. For information 
on Sing le-Carrier Cab inets, refer to DEFINITY Enterp rise Communic ations Server 
Release 8 Installation and  Test for Sing le-Carrier Cab inets.
Floor p lans and  eq uip ment layouts for typic al system installations are p rovid ed  in 
DEFINITY Enterp rise Communic ations Server Release 8 System Desc rip tion.
Unpack and Inspect Cabinets 
Perform these step s for all c abinets.
!DANGER:
A c ab inet may weig h as muc h as 800 lb  (363 kg ) and  may b e top  heavy. 
Use extreme c aution.
1. Chec k the status of the SHOCKWATCH and /or TILTWATCH ind ic ators on 
the c ontainer. If the c ontainer has b een shaken or tilted  b eyond  
sp ec ific ations, the ind ic ators are red , indic ating p otential damag e. Rep ort 
any damage according to local shipping instructions.
!DANGER:
Take c are to avoid  injury while c utting  and  removing  the 2 metal b and s.
2. Unpack the cabinet and remove all packing material. 
3. Move the c ab inets into their p rop er p ositions. 
4. Do not ad just the leveling  ft at this time. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Connect Cabinets 
1-2 Check Customer’s Order 
1
Unpack and Inspect Auxiliary Cabinet
The Auxiliary c ab inet is normally p ositioned  ad jac ent to the PPN c ab inet or the 
EPN c ab inet, if p rovid ed. 
1. Unp ac k the c ab inets as outlined on the p revious p ag e.
2. Remove the lower rear p anel from the Auxiliary c ab inet. Install the lower 
rear panel when the installation is c omp leted .
Unpack and Inspect Stratum 3 Clock Cabinet
1. Chec k the status of the SHOCKWATCH and /or TILTWATCH ind ic ators on 
the c ardb oard  c ontainer. If the c ontainer has b een jarred  or tilted  b eyond  
specifications, the indicators are red, indicating possible damage.
2. Remove all packing material.
3. Remove front d oor and  rear sc rew-on p anels from the c ab inet.
4. Inspect the cabinet for damage. Report any damage per local 
instruc tions.
Check Customer’s Order
1.Chec k the c ustomer’s order and  the ship ping  p ac king  lists to c onfirm all 
eq uip ment is p resent. If any eq uip ment is missing , report the information 
to your Luc ent Tec hnolog ies rep resentative. 
2. Ensure all c irc uit pac ks are fully inserted  into the prop er slots ac c ord ing  to 
the Customer Servic e Doc ument (CSD). Rep ort any d isc rep anc ies in 
c irc uit p ac k typ e or q uantity to your Luc ent Tec hnolog ies rep resentative.
3. Chec k the system ad junc ts for d amag e and  rep ort all d amag e ac c ord ing 
to loc al ship p ing  instruc tions.
Correcting Shipping Errors
1. Red-tag all defective equipment and over-shipped equipment and return 
p er the nearest Material Stoc king  Loc ation (MSL) instruc tions. For 
international c ustomers, c ontac t your ord er servic e ag ent.
2. Direc t all short-ship p ed  reports to the nearest MSL. Contac t the 
ap p rop riate loc ation for sp ec ific  instruc tions. For Streamlined  
Imp lementation in the United  States, c all 1-800-772-5409. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Connect Cabinets 
1-3 Install System Cabinets 
1
Install System Cabinets
Chec k the loc ation of the AC p ower rec eptac les in the eq uip ment room. The 
rec ep tac les must b e on a separately fused  circuit not controlled b y a wall switch. 
They must b e loc ated  within 10 ft (3 m) of the c ab inet and  outsid e the Main 
Distrib ution Frame (MDF) area.
Position the PPN Cabinet
1. If the system is sup p lied  with c ab le d uc twork, sp ac e the c ab inets on 32 in. 
(81.3 c m) c enters + -1/8 in. (0.3 c m), they must b e level, and  must b e 
sq uare with resp ec t to eac h other.
2. If the system is supplied with cable slack managers, place the cabinets far 
enoug h from the c onnec tion field  to lay down the 32 in. (81.3 c m) slac k 
manag ers and  to p rovid e a little extra room for the c ab les to ac c ess the 
cab le slack manag ers.
3. If earthquake p rotec tion is req uired , skip  to ‘‘
Earthq uake Protec tion 
Installation’’ on p age 1-33.
4. If earthq uake p rotec tion is not req uired , level the c ab inets and ad just and  
loc k the c ab inet stab ilizing  bolts to keep  the c ab inet from moving .
5. At the bottom of the c ab inet, install hole p lug s (p rovid ed  with c ab inet) in 
the holes p reviously oc c up ied  b y the 4 c arriag e b olts.
Position the EPN Cabinets
Eac h EPN c ab inet is normally p ositioned  ad jac ent to the PPN c ab inet b ut may be 
loc ated  remotely in a d ifferent room or a d ifferent build ing .
1. The p roc ed ure for installing  an EPN c ab inet is the same as for the PPN 
c ab inet.
2. If earthquake p rotec tion is req uired , skip  to ‘‘
Earthq uake Protec tion 
Installation’’ on p age 1-33.
3. If earthq uake p rotec tion is not req uired , level the c ab inets and ad just and  
loc k the c ab inet stab ilizing  bolts to keep  the c ab inets from moving .
NOTE:
To install a new EPN c ab inet to an existing system, refer to DEFINTY 
Enterprise Communic ations Server Release 8 Up g rad es and  
Ad ditions for R8r. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Connect Cabinets 
1-4 Install System Cabinets 
1
Position the Auxiliary Cabinet (Optional)
1. Position the Auxiliary c ab inet next to the PPN c abinet (or EPN c ab inet, if 
installed ). The loc ation of eq uip ment inside the Auxiliary c ab inet is 
sp ec ified  in the Customer Servic e Doc ument (CSD).
2. If earthquake p rotec tion is req uired , skip  to ‘‘
Earthq uake Protec tion 
Installation’’ on p age 1-33. Return to this sec tion when finished .
3. If earthq uake p rotec tion is not req uired , level the c ab inets and ad just and  
loc k the c ab inet stab ilizing  bolts to keep  the c ab inet from moving .
Install Auxiliary Cabinet Equipment
The Auxiliary c ab inet allows for c arrier, 23-in. (58.4 c m) rac k, or p anel mounting  
of hard ware. The following  equip ment is furnished with the c ab inet. 
nFuse panel — Distributes -48 VDC p ower to fused  c ab inet c irc uits
nPower receptacle strip — Provid es switc hed  and  unswitc hed  120 
VA C  r e c e p t a c l e s
nDC c onnec tor b loc k — Req uired  when Auxiliary c ab inet is 
powered by an external DC source
nAC to DC power sup p ly — Converts AC p ower p rovid ed by the AC 
p ower strip  switc hed  outlet to the req uired  DC voltag e
1. Install eq uip ment insid e the c ab inet as sp ec ified in the CSD. The following  
op tional equip ment c an b e installed :
nAud ic hron H9040 Wake-Up  Announc ement System
n909A/B Universal Coup ler
n7400 Series Data Mod ules
nZ77A Multip le Data Mounting  
nFan Assemb ly — Requires 120 volt AC power
nCOMSPHERE 3000-series mod ems
nExternal Channel Servic e Unit (CSU) — 1 is req uired  for eac h T1 
c arrier link
nPa g e Pa c  Pa g in g  Sys t e m  — 3 mod els are availab le. All Pag ePac  
mod els require 120 VAC power.
nMod el 15A Announc ement System — See Ta b l e  1 - 1 for PEC 
codes. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Connect Cabinets 
1-5 Install System Cabinets 
1
The BLD1 c irc uit p ac k p rovid es 8 c hannels with up  to 20 sec ond s of 
rec ord ing  time on eac h c hannel. The BLD2 c irc uit p ac k provid es 8 
c hannels with up  to 40 sec ond s of rec ording  time on eac h c hannel. Eac h 
c hassis c an b e p op ulated  with any c omb ination of 2 BLD c irc uit p ac ks.
The Model 15A Announc ement System is FCC registered and  d oes not 
req uire a voic e c oup ler.
2. If earthquake p rotec tion is req uired , skip  to ‘‘
Earthq uake Protec tion 
Installation’’ on p age 1-33.
Install and Position Stratum 3 Clock Cabinet
Chec k the loc ation of the AC p ower rec eptac le. The rec eptac le must b e on a 
sep arately fused  c irc uit that is not c ontrolled  b y a wall switc h. It must b e loc ated  
within 10 ft (3 m) of the c ab inet and  should  b e loc ated  outsid e the MDF area.
1. Position the c loc k c ab inet in the d esig nated  loc ation. 
2. If earthquake p rotec tion is req uired , skip  to ‘‘
Earthq uake Protec tion 
Installation’’ on p age 1-33.
3. If earthq uake p rotec tion is not req uired , level the c ab inets and ad just and  
loc k the c ab inet stab ilizing  bolts to keep  the c ab inet from moving .
Table 1-1. Model 15A Announcement Equipment
PEC Code Description
PEC 63240 1 c hassis and  1 BLD1 c irc uit p ac k
PEC 63241 1 BLD1 c irc uit p ac k
PEC 63242 1 c hassis and  1 BLD2 c irc uit p ac k
PEC 63243 1 BLD2 c irc uit p ac k
PEC 63246 1 remote rec ord  mod ule 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Connect Cabinets 
1-6 Connect AC Power and Ground 
1
Connect AC Power and Ground
Power Requirements
Tab le 1-2 shows the p ower req uirements. 
J58890CE-1, J58890CE-2, and J58890CH-1
The following proc ed ures app ly to the AC-powered  PPN and  EPN c ab inets. 
Either of the following  p ower sourc es c an supp ly 60 Hz p ower to the AC load  in 
Release 5 and later systems: 
nSing le-p hase, 4-wire, 120/240 VAC sup p lying  240 VAC. This sourc e has 2 
hot wires, 1 g round  wire, and 1 neutral wire (J58890CE).
nSing le-p hase, 4-wire, 120/208 VAC sup p lying  208 VAC. This sourc e has 2 
hot wires, 1 g round  wire, and 1 neutral wire (J58890CE).
nSing le-p hase, 3-wire, 208 or 240 VAC. This sourc e has 2 hot wires and  1 
g round  wire (J58890CH).
Either of the following  p ower sourc es c an supp ly 50 Hz p ower to the AC load  in 
Release 5 and later systems:
nNon-United  States 5-wire, Y, 220/380 VAC. This sourc e has 3 hot wires, 1 
neutral wire, and  1 g round  wire.
nNon-United  States Delta, 4-wire, 220 or 240 VAC. This sourc e has 3 hot 
wires and  1 g round  wire.
Table 1-2. DEFINITY System Power Requirements
Maximum DEFINITY UL Rating Label Power Capacity
Va c  I
nIac I
nMax W I
nBTU/Hr
208 24 3245 11071.26
240 21 3276 11177.71
120 40 3120 10645.44 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Connect Cabinets 
1-7 Connect AC Power and Ground 
1
Tab le 1-3 describes the power sources and required AC input power.
NOTE:
The typ e of p ower req uired  is shown on the c ab inet’s rear d oor.
!CAUTION:
The eq uip ment room AC power and ground  wiring  must b e p erformed  b y a 
q ualified  elec tric ian. Refer to DEFINITY Enterp rise Communic ations Server 
Release 8 System Desc rip tion Poc ket Referenc e, for site req uirement 
information.
!CAUTION:
The p ower c irc uit must b e d ed ic ated  to the system and  must not b e shared  
with other eq uip ment and  must not b e c ontrolled  b y a wall switc h. The AC 
rec ep tac le should  not b e loc ated  und er the MDF.
!CAUTION:
System g rounding  must c omp ly with the g eneral rules for g round ing  
c ontained  in Artic le 250 of the National Elec tric al Cod e (NEC), National Fire 
Protec tion Ag enc y (NFPA) 70, or the ap p lic ab le elec tric  c od e in the c ountry 
c ontaining  the eq uip ment. For more information, refer to ‘‘
Approved 
Ground s’’ on page 1-22.
Table 1-3. AC Power Sources and Plug Type
Power Distribution 
Unit Power Sources Power Input
AC power distribution 
(J58890CE-1 and 
J58890CE-2) 
Multicarrier Cab inetSing le p hase 120 VAC 
with neutral 
Sing le p hase 240 VAC 
with neutral, or sing le 
phase of 3-phase, 208 
VAC with neutral120 VAC, 60 Hz NEMA 
5-50R
208/240 VAC, 60 Hz NEMA 
L14-30R 
AC power distribution 
(J58890CH-1) 
Multicarrier Cab inetSing le Phase 176-264 
VA C  200-240 Volts, 50-60 Hz 
NEMA L6-30R. Installations 
outsid e the United  States 
require a receptacle 
suitab le for use in the 
c ountry of installation.  
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Connect Cabinets 
1-8 Connect AC Power and Ground 
1
Connect Ground to AC-Powered System
(J58890CE)
Ground ing  is relatively simp le for an AC-p owered  system. Basic ally, the c ab inets 
c onnec t to the sing le-p oint g round  terminal bloc k loc ated  at either the AC load  
c enter or to a separate sing le-point g round  b loc k wired  to the AC load  c enter (or 
op tional AC p rotec tor c ab inet). 
nThe ap p roved  g round  wire must b e a g reen (or g reen with yellow strip e), 6 
AWG (#40) (16 mm2), c op p er, strand ed  wire.
nBond  all ap p roved  g round s at the sing le-p oint ground  to form a sing le 
g round ing elec trod e system.
AC Load Center is 50 ft (15.2 m) or Less from 
Cabinet
1. At the bottom rear of the PPN c ab inet, c onnec t a 6 AWG (#40) (16 mm2) 
CABINET GROUND wire to the c ab inet g round  terminal b loc k. See 
Fi g u re  1 - 1
.
2. Route the CABINET GROUND wire to the sing le-point g round  b loc k at the 
AC load  c enter and  c onnec t.
3. At the bottom rear of the first EPN c ab inet (if p rovid ed ), c onnec t a 6 AWG 
(#40) (16 mm
2) CABINET GROUND wire to the c ab inet g round  terminal 
block.
4. Route the CABINET GROUND wire to the sing le-point g round  b loc k at the 
AC load  c enter and  c onnec t.
NOTE:
If the EPN c ab inet is loc ated  remote from the PPN c ab inet (in a 
sep arate room or build ing ), c onnec t the CABINET GROUND wire to 
an ap p roved  ground. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Connect Cabinets 
1-9 Connect AC Power and Ground 
1
Figure 1-1. Typical Cabinet Ground Location
5. Rep eat c onnec ting  eac h EPN c ab inet to the sing le-p oint g round bloc k.
6. At the AC load c enter, c onnec t a 10 AWG (#25) (6 mm
2) wire to the 
sing le-p oint g round  b loc k. This g round  wire will later b e tie-wrap p ed  to the 
trunk c ab les and  c onnec ted  to the Coupled  Bond ing  Cond uc tor (CBC) 
g round  b loc k at the MDF. Figure Notes
1. PPN Cab inet
2. EPN Cab inet (if Installed )
3. 6 AWG (#40) (16 mm
2) CABINET GROUND 
Wi re
4. Cabinet Ground  Terminal Bloc k5. AC Load  Center 
Single-Point Ground
6. Less than 50 Wire ft 
(15.2 m)
7. 10 AWG (#25) (6 mm
2) 
Ground  Wire to CBC
widmgrnd LJK 092697
122
333
444
5
6
7 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Connect Cabinets 
1-10 Connect AC Power and Ground 
1
AC Load Center is More Than 50 ft (15.2 m) from 
Cabinet
1. Mount the sing le-p oint ground b loc k to any surfac e b etween the MCC 
c ab inets and  the AC load  c enter sing le-p oint g round . The sing le-p oint 
g round  b loc k must b e mounted  to a non-metallic  surfac e.
2. At the bottom rear of the PPN c ab inet, c onnec t a 6 AWG (#40) (16 mm
2) 
CABINET GROUND wire to the c ab inet g round  b loc k. See Fi g u re  1 - 2
.
3. Route the wire to the sing le-p oint ground  b loc k and  c onnec t.
4. At the first EPN c abinet (if p rovid ed ), c onnec t a 6 AWG (#40) (16 mm
2) 
CABINET GROUND wire to the c ab inet g round  terminal b loc k.
5. Route the CABINET GROUND wire to the sing le-p oint g round  b loc k and  
c onnec t.
NOTE:
If the EPN c ab inet is loc ated  remote from the PPN c ab inet (in a 
sep arate room or build ing ), route the EPN CABINET GROUND wire 
to an ap p roved  g round .
6. Rep eat c onnec ting  eac h EPN c ab inet to the sing le-p oint g round bloc k.
7. Connect a 6 AWG (#40) (16 mm
2) g round  wire to an unused  terminal on 
the single-point ground block.
8. Route the ground wire to the AC load  c enter g round  and  c onnec t.