Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation And Test For Multi-Carrier Cabinets Manual

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-107 Add ISDN—BRI 
5
Add Circuit Packs
1. Determine port assig nment of c irc uit p ac ks to be ad d ed .
2. Install the ap p rop riate c irc uit pac ks in assigned  c ab inet slot (as req uired ). 
For example:
The TN794 Pac ket Interfac e c irc uit p ac k and  the TN556 or TN2198 ISDN 
BRI c irc uit p ac k are required . The TN794 Pac ket Interfac e c irc uit p ac k 
should  b e add ed  first. If an EPN is p resent, a TN570/B/C Exp ansion 
Interfac e c irc uit p ac k is req uired .
Install Cables
1. Install c ab les from c ab inet to the MDF as req uired .
NOTE:
BRI req uires a 12-p ort b ac kp lane c ab le terminator (b reakout 
c onnec tor). Connec t this terminator to the 25-p air c ab le. This is 
d ifferent from the 8-p ort c onnec tor used  for DCP.
Enter Added Translations
1. Ad minister the req uired  translation d ata using the forms listed und er 
7500D voic e terminals and  8500 voic e terminals in DEFINITY Enterp rise 
Communic ations Server Release 8 Ad ministrator’s Guid e.
Resolve Alarms
1. Examine the alarm log . Resolve any alarms using  DEFINITY Enterp rise 
Communic ations Server Release 8 Maintenanc e for R8si. 
Save Translations
1. If the system is hig h or c ritic al reliab ility, typ e status system 1
 and press 
En t e r  to verify that the system is in the “ ac tive/stand b y”  mode.
2. Type save translation
 and press 
En te r. This instruc ts the system to take all 
translation information in memory and  write it to the translation c ard s.3 A 07 01
Cab inet
(Port Network)Carrier Slot 
NumberPo r t  
Numb er 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-108 CAMA/E911 Installation 
5
3. If the system c ontains a TN750/B/C Announc ement c irc uit pac k, typ e list 
configuration software-version
 and  p ress 
En t e r. To restore these 
announc ements, typ e restore announcements
 and  press 
En t e r.
4. Update backup cards, if required.
CAMA/E911 Installation
Configuration
The CAMA/E911 feature will only work on DEFINITY ECS if TN429C CO circuit 
packs (or later suffix) is used.
Por t Networks (PNs) that include TN429C circuit packs used to interface to CAMA 
trunks may require some CPTR resources to be either TN744D V2 or TN2182B 
circuit packs, since TTR/CPTR or General Purpose Tone Receiver (GPTR) 
resources are selected from the pool available in the PN when needed.
Table 5-25
 denotes which of these circuit packs are compatible and which are not 
affected.
Ta b l e  5 - 2 5 .Compatibility Tone Clock, TTR/CPTR, and GPTR Circuit Packs
Circuit 
Pack DescriptionCompatibility 
with CAMA 
Trunks in 
Same PN Application Notes
TN420 
TN420B 
TN420CTouch Tone 
Detector / Call 
Progress Tone 
DetectorNot Compatible Not used in the 
U.S.4TTR and 2 CPTR 
ports. Used in 
combination with 
the TN780 in 
many countries 
initially in ver-
sions prior to 
G3V3.3. Use 
TN744DV2 if 
CAMA feature is 
to be supported.
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-109 CAMA/E911 Installation 
5
TN744 
TN7744B 
TN744C 
TN744DV1Call Classifier - 
DetectorNot Compatible Used globally 8 GPTR/call clas-
sification ports. 
Used for call clas-
sification only ini-
tially prior to 
G3V3.3. Becomes 
a GPTR resource 
in G3V3.3 and 
later. Use 
TN744DV2 if 
CAMA feature is 
to be supported.
TN744DV2 Call Classifier - 
DetectorCompatible Used globally 8 GPTR/call clas-
sification ports. 
Required in PN 
supporting CAMA 
trunks if GPTR 
resources are 
required in excess 
of those on the 
TN2182BV2. 
Also required (if 
the TN768 or 
TN780 tone clocks 
are used) in place 
of TN748, TN744, 
and TN744B and 
TN744C.
TN748 
TN748B 
TN748C 
TN748DTouch Tone 
Detector / Call 
Progress Tone 
DetectorNot Compatible Used in the 
U.S. and a few 
other countries4 TTR and 2 
CPTR ports. Used 
in combination 
with the TN756, 
TN768, or TN780 
in many countries 
initially in ver-
sions prior to 
G3V3.3. Use 
TN744DV2 if 
CAMA feature is 
to be supported.
Ta b l e  5 - 2 5 .Compatibility Tone Clock, TTR/CPTR, and GPTR Circuit Packs
 — Continued
Circuit 
Pack DescriptionCompatibility 
with CAMA 
Trunks in 
Same PN Application Notes
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-110 CAMA/E911 Installation 
5
TN756 Tone Detector 
GeneratorNot Compatible Used in the 
U.S. and a few 
other countriesTo n e  d e t e c -
tor/tone clock with 
4 TTR and 2 
CPTR ports. Used 
in combination 
with the TN748 in 
many countries 
initially in ver-
sions prior to 
G3V3.3. Used 
only with 
SCC/ESCC cabi-
nets with no 
EPNs, no duplica-
tion, no ASAI. 
Use TN2182BV2 
if CAMA feature 
is to be supported.
TN768 Tone Clock Not Affected Used in the 
U.S. and many 
other countriesTone clock only, 
no TTR/CPTR 
functionality. Typ-
ically found with 
TN748 circuit 
packs in the U.S. 
Use TN7744DV2 
instead of TN748 
with CAMA.
TN780 Tone Clock Not Affected Used in the 
U.S. (infre-
quently) for 
stratum 3 clock-
ing and used in 
many other 
countriesTone clock only, 
no TTR/CPTR 
functionality. Typ-
ically found with 
TN748 circuit 
packs in the U.S. 
Use TN7744DV2 
instead of TN748 
with CAMA.
Ta b l e  5 - 2 5 .Compatibility Tone Clock, TTR/CPTR, and GPTR Circuit Packs
 — Continued
Circuit 
Pack DescriptionCompatibility 
with CAMA 
Trunks in 
Same PN Application Notes
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-111 CAMA/E911 Installation 
5
Hardware Setup
1. Insert the TN429C CO c irc uit p ac k in any availab le p ort slot.
2. Wire the TN429C to the MDF (the trunk from the CO). Refer to the p inouts 
in Tab le 5-40
.
Administration Setup
1. At the promp t, type add trunk next
 and press En t e r.
Screen 5-1. CAMA Trunk Group form (page 1)
TN2182 
TN2182BTone Clock / 
Call Classifier - 
DetectorCompatible Used globally Tone clock plus 8 
GPTR/call classi-
fication ports. Use 
TN2182B if 
CAMA feature is 
to be supported.
Ta b l e  5 - 2 5 .Compatibility Tone Clock, TTR/CPTR, and GPTR Circuit Packs
 — Continued
Circuit 
Pack DescriptionCompatibility 
with CAMA 
Trunks in 
Same PN Application Notes
Continued on next page
  
                                                                     Page 1 of 11
                               TRUNK GROUP
Group Number: 1                  Group Type: cama      CDR Reports: y
  Group Name:  cama Trunk Group - E911  COR: 1     TN: 1       TAC: 701
   Direction: outgoing     Outgoing Display? y CESID I Digits Sent: 0
                             Busy Threshold: 99
TRUNK PARAMETERS
         Trunk Type: wink-start
 Outgoing Dial Type: r1mf
  Trunk Termination: rc
                             
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-112 CAMA/E911 Installation 
5
2. On Trunk Group sc reen (pag e 1), in the Group Type:
 field , enter cama
.
3. In the Group Name:
 field , enter the d esired  name. 
4. In the TAC:
 field , enter the d esired  trunk ac c ess c od e. 
5. In the Outgoing Display:
 field , enter y
.
6. In the CESID I Digits Sent:
 field , enter the number d irec ted  b y the 
Central Offic e (CO) or the Pub lic  Safety Answering Point (PSAP).
7. Sc roll to p ag e 3 of the form.
Screen 5-2. Administrable Timers form (page 3)
8. On the Administrable Timers sc reen (page 3), you may need to adjust 
these field s ac c ord ing  to your CO. Sc roll to pag e 5.
 
Screen 5-3. Group Member Assignments form (page 5)
  
                                                                     Page 3 of 11
                              TRUNK GROUP
ADMINISTRABLE TIMERS
                                       Outgoing Disconnect (msec): 400
                                  Cama Outgoing Dial Guard (msec): 75
                                      Outgoing Glare Guard (msec): 1000
                                      Cama Wink Start Time (msec): 5000
 Outgoing End of Dial (sec): 1    Outgoing Seizure Response (sec): 4
                                    Disconnect Signal Error (sec): 30
                                                                    Page 5 of 11
                                TRUNK GROUP
                                       Administered Members (min/max):  1/2
GROUP MEMBER ASSIGNMENTS                   Total Administered Members:  2
     Port   Code   Sfx  Name
 1: 01C0401 TN429   C
 2: 01C0402 TN429   C
 3:
 4:
 5:
 6:
 7:
 8:
 9.
 10:
 11:
 12:
 13: 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-113 CAMA/E911 Installation 
5
9. On the Group  Memb er Assig nments sc reen, in the Port
 field , ad d the 
trunk memb ers and press 
En t e r when finished .
10. At the promp t, type change feature-access-code
 and press 
En t e r.
Screen 5-4. Feature Access Code (FAC) form (page 1)
11. The Feature Ac c ess Cod e (FAC) sc reen (p ag e 1) ap p ears.
12. In the Auto Route Selection (ARS) Access Code 1:
 field, 
ad minister the ARS ac c ess c od e (in the examp le above, typ e 9
) and press 
En t e r  (must matc h d ial p lan).
13. At the promp t, type change ars analysis 
 and press 
En t e r.
                                 Page 1 of 5
                                FEATURE ACCESS CODE (FAC)
             Abbreviated Dialing List1 Access Code: ____
             Abbreviated Dialing List2 Access Code: ____
             Abbreviated Dialing List3 Access Code: ____
Abbreviated Dial - Prgm Group List Access Code: ____
                          Announcement Access Code: ____
                           Answer Back Access Code: ____
          Auto Alternate Routing (AAR) Access Code: ____
          Auto Route Selection (ARS) Access Code 1: 9___  Access Code 2: ____
                     Automatic Callback Activation: ____   Deactivation: ____
Call Forwarding Activation Busy/DA: ____ All: ____  Deactivation: ____
                             Call Park Access Code: ____
                           Call Pickup Access Code: ____
   CAS Remote Hold/Answer Hold-Unhold Access Code: ____
                      CDR Account Code Access Code: ____
Change Coverage: ____
                      Data Origination Access Code: ____
                          Data Privacy Access Code: ____
Directed Call Pickup Access Code: ____
         Emergency Access To Attendant Access Code: ____
Extended Call Fwd Activate Busy D/A: ____  All: ____  Deactivation: ____
                   Facility Test Calls Access Code: ____
                                 Flash Access Code: ____ 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-114 CAMA/E911 Installation 
5
Screen 5-5. ARS Digit Analysis Table
14. An ARS Dig it Analysis Table sc reen ap p ears. In the Dialed String
 field, 
in the first emp ty row, typ e 11
.
15. In the Total Mn
 field , typ e 2
.
16. In the Total Mx
 field , typ e 2
.
17. In the Rte Pat
 field , enter the d esired  Route Pattern (in the examp le 
ab ove the route p attern is 11).
NOTE:
For the following  step , if you are using the Attend ant Crisis Alerting  
feature, typ e alrt
 instead  of “ emer.”
18. In Call Type
 field , typ e emer
.
19. On the next emp ty row, in the Dialed String
 field , typ e 911
.
20. In the Total Mn
 field , typ e 3
.
21. In the Total Mx
 field , typ e 3
.
22. In the Rte Pat
 field , typ e the d esired  Route Pattern (in the example 
ab ove the route p attern is 12).
NOTE:
For the following  step , if you are using the Attend ant Crisis Alerting  
feature, typ e alrt
 instead  of “ emer.”
23. In the Call Type
 field , typ e emer
 and press 
En te r.
                              ARS DIGIT ANALYSIS TABLE
                            Partitioned Group Number:  _     Percent Full:    ___
Dialed      Total  Rte Call Nd  ANI Dialed      Total  Rte Call Nd ANI
     String      Mn Mx  Pat Type Num Rq String      Mn Mx  Pat Type Num Rq
9________________ 7_ 7_  2__ hnpa ___ n __________________ __ __ ___ ____ ___ _
976______________ 7_ 7_  den hnpa ___ n __________________ __ __ ___ ____ ___ _
11_______________ 2_ 2_  11_ emer ___ n __________________ __ __ ___ ____ ___ _
911______________ 3_ 3_  12_ emer ___ n __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _
_________________ __ __  ___ ____ ___ _ __________________ __ __ ___ ____ ___ _ 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-115 CAMA/E911 Installation 
5
24. At the p rompt, typ e change route-pattern 
 
(the route pattern to 
b e c hang ed; in the examp le ab ove, the route p attern is 11) and  p ress 
En t e r.
Screen 5-6. Route Pattern form (Page 1)
25. On the Route Pattern sc reen, in Grp. No
. field , enter the CAMA trunk 
g roup number.
26. In the FRL
 field , typ e 0
.
NOTE:
For the following  step , if the Central Offic e (CO) wants KP11ST as 
the d ialed dig it string , then leave b lank. If the CO wants KP911ST, 
then insert a “ 9”  in the Inserted Digits
 field .
27. Ad minister the Inserted Digits 
field  if need ed  and press 
En t e r.
28. At the p rompt, typ e change route-pattern 
 
(the route pattern to 
b e c hang ed; in the examp le ab ove, the route p attern is 12) and  p ress 
En t e r.
                      Page 1 of X
  Pattern Number: 11               
    Grp.  FRL NPA Pfx Hop Toll No. Del Inserted                             IXC
    No.           Mrk Lmt List Digits  Digits
 1: 1__   0  ___  _  __   __    __    ____________________________________ user
 2: ___   _  ___  _  __   __    __    ____________________________________ user
 3: ___   _  ___  _  __   __    __    ____________________________________ user
 4: ___   _  ___  _  __   __    __    ____________________________________ user
 5: ___   _  ___  _  __   __    __    ____________________________________ user
 6: ___   _  ___  _  __   __    __    ____________________________________ user
BCC VALUE  TSC CA-TSC   ITC BCIE Service/Feature           Numbering LAR
0 1 2 3 4 W    Request                                       Format
  1: y y y y y n  y none_____ both ept  outwats-bnd____ BAND: ___ ________  none
  2: y y y y y n  n           rest      _______________           ________  next
  3: y y y y y n  n           rest      _______________           ________  rehu
  4: y y y y y n  n           rest      _______________           ________  none
  5: y y y y y n  n           rest      _______________           ________  none
  6: y y y y y n  n           rest      _______________           ________  none 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-116 CAMA/E911 Installation 
5
Screen 5-7. Route Pattern form (Page 1)
29. On the Route Pattern sc reen, in Grp. No
. field , typ e the CAMA trunk 
g roup number and  p ress 
En te r.
30. In the FRL
 field , typ e 0
.
NOTE:
For the following  step , if the Central Offic e (CO) wants KP911ST as 
the d ialed dig it string , then leave b lank. If the CO wants KP11ST, 
then d elete one d ig it.
31. Ad minister No. Del Digits
 field  if need ed  and  p ress 
En t e r.
32. At the promp t, type change cama-numbering
 and press 
En t e r.
                      Page 1 of X
  Pattern Number: 12               
    Grp.  FRL NPA Pfx Hop Toll No. Del Inserted                             IXC
    No.           Mrk Lmt List Digits  Digits
 1: 1__   0  ___  _  __   __    1_    ____________________________________ user
 2: ___   _  ___  _  __   __    __    ____________________________________ user
 3: ___   _  ___  _  __   __    __    ____________________________________ user
 4: ___   _  ___  _  __   __    __    ____________________________________ user
 5: ___   _  ___  _  __   __    __    ____________________________________ user
 6: ___   _  ___  _  __   __    __    ____________________________________ user
BCC VALUE  TSC CA-TSC   ITC BCIE Service/Feature           Numbering LAR
0 1 2 3 4 W    Request                                       Format
  1: y y y y y n  y none_____ both ept  outwats-bnd____ BAND: ___ ________  none
  2: y y y y y n  n           rest      _______________           ________  next
  3: y y y y y n  n           rest      _______________           ________  rehu
  4: y y y y y n  n           rest      _______________           ________  none
  5: y y y y y n  n           rest      _______________           ________  none
  6: y y y y y n  n           rest      _______________           ________  none