Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation And Test For Multi-Carrier Cabinets Manual

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-87 Add External Modem to TN1648B 
5
Figure 5-39. Attach the Cable to the Pass-Thru Tool 
6. Slid e the tool to the front of the c ab inet. See Figure 5-40
.
7. Pull the tool (with ad apter and  c ab le attac hed ) out throug h the front of the 
c ab inet. 
8. Close the rear door.
9. Rep lac e the fan c over. See Fig ure 5-41
. Figure Notes
1. Pass-thru Tool
2. RJ45 (Telep hone Plug )3. Tie Wrap
fodacup3 EWS 082598
3
1
2
3 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-88 Add External Modem to TN1648B 
5
Figure 5-40. Insert the Pass-thru Tool
prda0009 EWS 090498 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-89 Add External Modem to TN1648B 
5
Figure 5-41. Replace the Fan Cover
10. Connec t the c ab le to the front of the TN1648B c irc uit p ac k. See 
Fi g u re  5 - 4 2
.
NOTE:
Dress the c ab le straig ht d own the front of the c irc uit pac k. Do not 
allow the c able to c ross in front of another c irc uit p ac k.
11. Attac h the c ab le mount to the c ab inet and  sec ure the c ab le. See 
Fi g u re  5 - 4 2
.
prda0006 EWS 010599
ENTER
/YES ENTER
/YES NEXT
/NO NEXT
/
NO BACK
BACK
AUDIX
AUDIXBOOT
/
SHUTDOWN BOOT /
SHUTDOWN
A
L
A
R
M
S ALARMS
E
M
E
RT
R EMER TR 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-90 Add External Modem to TN1648B 
5
Figure 5-42. Connect the Cable to the TN1648B Circuit Pack
12. Close the front d oor.
13. Discard the pass-thru tool.
Test the Installation
1. Log in to the manag ement terminal.
2. Ad minister the system b y referring  to the Installation and  Test for Ad junc ts 
and  Perip herals, 555-230-125.
3. Type list configuration all
 and  p ress 
En t e r to d etermine if the new c irc uit 
p ac k ap p ears in the c orrec t slot and  that there are no c irc uit p ac k 
conflicts.
Prda0011 KLC 091698 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-91 Add DCS Interface 
5
Add DCS Interface
Systems in a Distributed Communications System (DCS) network are 
interconnected by both tie trunks (for voice communications) and data links (for 
control and transparent feature information). These data links, also called DCS 
signaling links, support the feature transparency. 
Various subsets (depending on the specific configuration) of DS1 Interface circuit 
packs provide the voice-communications interface.
Meanwhile, the data link interface (between the processor and the physical 
signaling link) is provided by (or through) a TN799 Control-LAN circuit pack. In 
some configurations, the TN799 passes the signaling information over a separate 
10BaseT TCP/IP network (usually via a hub). For use with 10BaseT, connect the 
appropriate pins of the I/O field to the hub. For pinouts and diagrams, refer to the 
end of this chapter. In other configurations, the TN799 circuit pack carries 
signaling over point-to-point protocol (PPP) for subsequent inclusion (via the 
switching fabric) in the same DS1 bit stream as the DSC voice transmissions.
As an option to the TN768 Tone-Clock, a TN780 Tone-Clock circuit pack (installed 
in the PPN) can interface external Stratum 3 synchronization for DS1 connections.
For further information about DCS, refer to the following documents:
nAT&T System 75/85 Network and Data Services Reference Manual, 
555-025-201
nSystem 75 Application Notes Network Services, 555-209-002
nDEFINITY ECS Release 8 Administration for Network Connectivity, 
555-233-501
Add Circuit Packs
A DS1 circuit pack is required for Point-to-Point Protocol (PPP) connections. A 
TN799 Control-LAN circuit pack is required.
1. Determine the p ort assig nments of the c irc uit p ac ks to b e ad d ed . If there 
are no availab le p ort slots in the p roc essor c ab inet for the Control-LAN 
c irc uit p ac k, p lac e it in a R8 EPN c ab inet p ort slot. You d o not need  to 
p ower d own the c ab inet to install the c irc uit p ac k.  
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-92 Add DCS Interface 
5
Install Cables
1. Install c ab le from the c ab inet to a hub  or Internet Protoc ol (IP) Switc h as 
req uired. Connec t the 259A c onnec tor to the p ort slot c ontaining the 
Control-LAN circuit pac k. See Fig ure 5-43
. For a p inout of TN799, see 
Tab le 5-22
. 
Figure 5-43. Cable Connection for Control-LAN Figure Notes
1. 259A Connec tor
2. DW8 Cable3. Hub  or IP Switc h
1
2
3cydflan2  EWS 101398 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-93 Add Multiple Announcement 
5
Enter Added Translations
1. Get the DOSS order numb er of the upg rad e. Call the reg ional CSA to 
p erform the step s in this sec tion.
2. To enab le DCS, set the DCS
 field  on the System Parameters-Customer 
Options form to y
.
3. Ad minister the other req uired  translation data using  the forms listed  und er 
Distrib uted  Communic ations System (DCS) in DEFINITY Communic ations 
System Generic  4 V4 Imp lementation, 555-230-655.
Save Translations
1. If the system is hig h- or c ritic al-reliab ility, typ e status spe
 and press En te r  
to verify that the stand b y SPE is refreshed  and  that the stand b y d isk is in 
servic e.
2. Type save translation [spe-a or both] disk
 and press 
En te r. This 
c ommand  instruc ts the system to take all translation information in 
memory and  write it to the d isk(s).
Add Multiple Announcement
TN750C Multiple Announcement circuit packs are required if the system has 
multiple announcement circuit packs. At least 1 TN750C circuit pack is required. A 
maximum of 10 TN750C Announcement circuit packs are allowed in a system. No 
more than 1 TN750 or TN750B can reside in the system. The TN750C can install 
in any port or service (TDM) slot, and need not reside in a control carrier for extra 
power holdovers.
Table 5-22. TN799 Pinout
Backplane Pin 25-Pair Wire Color Lead NamePeripheral 
Connector Pin
103 White/Orang e TD+ 27
003 Orang e/White TD- 2
104 White/Green RD+ 28
004 Green/White RD- 3 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-94 Add Multiple Announcement 
5
The announcements from a TN750 or TN750B can be saved and then restored to 
a TN750C. 
NOTE:
Do not c op y or restore announc ements from a TN750C to a TN750 or 
TN750B c irc uit p ac k, as this p roc ess may c orrup t the announc ement d ata.
TN750C Announcement Circuit Pack
The TN750C circuit pack contains on-board flash memory which provides internal 
backup of announcements on the circuit packs. Thus, the TN750C circuit pack 
does not need the save and restore processes. However, you can use the save 
and restore processes to copy announcements from the TN750 or TN750B to a 
TN750C circuit pack.
The TN750C circuit pack can replace a TN750 or TN750B circuit pack. The 
difference in operation is that the TN750C circuit pack automatically restores and 
repor ts the availability of announcements from its own internal flash memory in 5 
minutes, rather than the approximately 40 minutes for the TN750 or TN750B 
circuit pack repor ting from the mass-storage system.
If a circuit pack already has announcements in its flash memory, the yellow LED 
flashes as the announcements copy to the Voice RAM. 
Save and Restore Recorded Announcements
!CAUTION:
If the yellow LED is on, d o not remove the c irc uit p ac k. This will c orrup t the 
announc ement data.
The syntax for saving from any TN750 circuit pack is save announcements [from 
PCSS] and press 
En t e r .  Where P is the port network number (1 for PPN, and 2-4 
for EPN), C is the carrier designation (A, B, C, D, or E), and SS is the number of 
the slot in which the circuit pack resides (01 to 21). 
The syntax for restoring to a TN750C circuit pack is restore announcements 
[disk | removable media [to PCSS]] and press 
En te r.  Where P is the port network 
number (1 for PPN, and 2-4 for EPN), C is the carrier designation (A, B, C, D, or 
E), and SS is the number of the slot in which the circuit pack resides (01 to 21). 
When executing a restore command and there are existing announcements on the 
circuit pack, the following warning message appears:
WARNING: This restore announcement command will overwrite 
the existing announcements on the specified 
board. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-95 Add Multiple Announcement 
5
After 5 minutes (with no alterations to the announcements), the TN750C 
automatically copies the announcements from the Voice RAM to the internal flash 
memory. The yellow LED on the front of the TN750C flashes.
You can only save the announcement contents of 1 circuit pack to mass storage at 
a time. For the contents of every circuit pack, save to separate translation cards. 
Label each card to match the circuit pack saved to it.
TN750 and TN750B Announcement Circuit Packs
NOTE:
The following  save and  restore p roc ed ures are only nec essary for TN750 
and  TN750B announc ement c irc uit p ac ks.
The recorded announcements in the system can be saved on the mass-storage 
system by typing save announcements spe-active/spe-standby and pressing 
En t e r. These commands should only be used after business hours or when the 
system is operating during a low-usage period. The system takes about 40 
minutes to transfer the recorded announcements from the announcement circuit 
pack to the mass-storage system. During this time period, the management 
terminal cannot be used to administer the system until the transfer finishes; 
however, all other administration terminals, if provided, are allowed to perform 
administration procedures.
The recorded announcements in the system can be restored to system memory 
from the translation card by entering the restore announcements command. 
Replace a TN750B with a TN750C or Move all
Announcements from a TN750B to a TN750C 
Use this procedure to replace a TN750B circuit pack with a TN750C circuit pack 
or to move every announcement from a TN750B to a TN750C.
NOTE:
Do not c op y or restore announc ements from a TN750C to a TN750 or 
TN750B c irc uit p ac k, as this may c orrup t the announc ement d ata.
1. Save announc ements from the TN750/B to the mass-storag e system.
2. Insert the TN750C c irc uit p ac k into a vac ant slot of a c arrier.
NOTE:
Any c arrier is ac c ep tab le sinc e power hold over is not a c onc ern.
3. Lift the loc king lever upward  until the latc h p in eng ag es.
4. Ad minister a new d ata mod ule on the TN750C c irc uit p ac k, as d esc rib ed  
in DEFINITY Enterp rise Communic ations Server Release 8 Ad ministrator’s 
Guid e. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-96 Add Multiple Announcement 
5
5. Type restore announcements
 and  p ress En te r  to the TN750C c irc uit p ac k 
eq uip ment loc ation.
6. Wait until announc ements c op y from voic e RAM to flash memory (yellow 
LED on the TN750C stop s flashing ). This may take ab out 10 minutes.
7. Type busyout board 01c11
 and  p ress 
En t e r for the TN750/B c irc uit p ac k, 
where “01c11
”  is an examp le c irc uit p ac k loc ation.
8. Type change integrated announcements
 and press 
En te r. This mod ifies 
the translations for the TN750B c irc uit pac k to referenc e the TN750C 
circuit pack.
9. Verify prop er p layb ac k of the announc ements from the TN750C c irc uit 
pack by calling them.
10. Typ e release board 01c11
 and press 
En t e r for the TN750/B c irc uit p ac k, 
where “01c11
”  is an examp le c irc uit p ac k loc ation.
Add TN750C Circuit Packs
1. Install the TN750C into a vac ant slot in a c arrier.
NOTE:
Any c arrier is ac c ep tab le sinc e power hold over is not a c onc ern.
2. Ad minister a new d ata mod ule on the TN750C c irc uit p ac k, as d esc rib ed  
in DEFINITY Enterp rise Communic ations Server Release 8 Ad ministrator’s 
Guid e.
3. Ad minister new announc ements to that TN750C slot b y typ ing change 
announcements
 and  p ress 
En te r . Fill in the “ d esig nated  b oard  loc ation”  
field  for the c irc uit p ac k’s loc ation.
4. Rec ord  the announc ements, as d esc ribed  in DEFINITY Enterp rise 
Communic ations Server Release 8 Ad ministrator’s Guid e.
5. Wait until the announc ements c op y from voic e RAM to the on-b oard  flash 
memory (the yellow LED on the TN750C starts and  then stops flashing ). 
This may take ab out 10 minutes.
Move a Single Announcement from 1
Announcement Circuit Pack to Another
1. Type change announcements
 and  p ress En t e r to c hang e the c irc uit p ac k 
loc ations of a p artic ular announc ement. You may also c hang e the 
c omp ression rate at this time.
2. Rerec ord  the announc ement, as d esc rib ed  in DEFINITY Enterp rise 
Communic ations Server Release 8 Ad ministrator’s Guid e.