Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation And Test For Multi-Carrier Cabinets Manual

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-77 Add DS1 Tie and OPS 
5
4. After the system reb oot is finished  and  all troub le is c leared , verify that the 
EMERGENCY TRANSFER CONTROL switc h is set to AUTO. This restores 
the system to the normal mod e.
Enter Added Translations
Administer forms listed under “DS1 Tie Trunk Service” in DEFINITY Enterprise 
Communications Server Release 8 Administrator’s Guide
.
Save Translations
1. If the system is hig h or c ritic al reliab ility, typ e status system 1
 and press 
En t e r to verify that the system is in the “ ac tive/standb y”  mod e.
2. Type save translation
 and press 
En te r. This instruc ts the system to take all 
translation information in memory and  write it to the translation c ard  or 
removab le med ia.
3. If the PPN c ontains a TN750 Announc ement c irc uit p ac k, typ e list 
configuration software-version
 and  p ress 
En t e r.
If Pag e 2 of this form shows that rec orded  announc ements were saved , 
these announc ements c an b e restored  using the restore announc ements 
command. Type restore announcements
 and  p ress 
En te r.
Resolve Alarms
Examine the alarm log. Resolve any alarms that may exist using DEFINITY 
Enterprise Communications Server Release 8 Maintenance R8si
. 
Enable Customer Options and Alarm Origination 
to INADS
1. Get the DOSS order number of the upgrade from the project manager and 
ask the reg ional Customer Software Ad ministration to c omp lete the step s 
in the shad ed  b ox. See ‘‘
Where to Call for Tec hnic al Sup p ort’’ on page -xvii 
for telep hone numb ers.
NOTE:
As p art of the system reg istration p roc ess, the INADS Datab ase 
Ad ministrator enab les Alarm Orig ination.
2. When ad ministration is c omp leted , log  in as craft
 at the Login:
 prompt. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-78 Add Speech Synthesis 
5
Add Speech Synthesis
The Speech Synthesizer circuit pack is required when the Voice Message 
Retrieval, Automatic Wakeup, or Do Not Disturb features are activated. The circuit 
pack does not require administration.
1. Determine the p ort assig nment of the Sp eec h Synthesizer c irc uit p ac k to 
be added.
2. Install the Sp eec h Synthesizer c irc uit p ac k in the d esig nated  c arrier slot.
See Figure 5-19
 for list of circuit packs.
Add Code Calling Access
The tones for the Code Calling feature are generated by the Tone-Clock circuit 
packs in the port networks.
1. Install a TN763B/C/D (or TN417) Auxiliary Trunk c irc uit p ac k or a Sp eec h 
Synthesizer c irc uit p ac k and  c onnec t for Loud sp eaker Pag ing . The Cod e 
Calling  Ac c ess feature shares the same p orts as Loud sp eaker Pag ing . An 
Auxiliary Trunk c irc uit p ac k p rovid es 4 p orts for Loud sp eaker Pag ing  and  
Cod e Calling  Ac c ess.
2.
Ad minister the form listed  und er “ Cod e Calling  Ac c ess”  in DEFINITY 
Enterp rise Communic ations Server Release 8 Ad ministrator’s Guid e.
init login administration:
1. Log in as init
.
2. Type change system-parameters customer-options
 and press 
En te r 
to verify that the c ustomer op tions are p roperly set.
3. Go to sc reen 6, QSIG Op tional Features, and  set the Basic Call 
Setup 
field  to y
 if the customer was using Supplementary Services 
Protoc ol b  or d  on an ISDN-PRI trunk g roup  b efore the up g rad e.
4. Type change system-parameters offer-options
 and  p ress 
En te r.
5. If the Activate Offer
 field  is n
, set it to y 
and press 
Ta b. A warning  
messag e lets you know whether you need  to save translations and  
reb oot to make the c hang e p ermanent.
6. Press 
En t e r to effec t the c hang es or Canc el if there were no c hang es.
7. Contac t the req uester when d one. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-79 Add Pooled Modem 
5
Add Pooled Modem
Modem Pooling supports 2 kinds of conversion resources: integrated and 
combined. 
The integrated type requires a TN758 Pooled Modem circuit pack for each 2 
conversion resources provided.
The combined type requires a port on a TN754B Digital Line circuit pack and a 
port on either an 8-port TN742, TN769; a 16-port TN746B; or a 24-port TN793/B, 
TN2793/B Analog Line circuit pack for each conversion resource provided.
The pooled modem requires a Lucent WP90110 L7 power supply. Although an 
integrated conversion resource can use either the L5 or L7, the combined only 
works with an L7.
!CAUTION:
The L5 and  L7 p ower supp lies look id entic al. Chec k the list numb er on the 
power supply before installing.
1. Determine the p ort assig nment of the c irc uit p ac ks to b e ad d ed  (if 
req uired ).
2. Install the ap p rop riate c irc uit pac ks in assigned  c arrier slot (if req uired ).
3. For Paradyne 3800 Series mod ems:
a. Type AT&F&D2&S4\D3S2=128x7V2S7=60S85=1
 and  p ress 
En te r. 
b. Type ATY0S10=100S78=2M0E0\N1&W
 and  p ress 
En t e r.
4.For other typ es of mod ems, refer to the vend or’s d oc umentation.
Settings for Modem Connected to Data Module
1. Type add data-module next
 and press En t e r.
2. Type pdm
 in the Type
 field .
3. Type x
 in the Port
 field.
4. Type dte
 in the Connected to
 field and press 
En te r.
5. Type add station next
 and press 
En t e r.
6. Type 2500
 in the Type
 field.
7. Type x
 in the Port
 field.
8. Type n
 in the Tests
 field  and  p ress 
En te r.
9. Type add modem-pool next
 and  p ress 
En te r.
10. Typ e combined
 in the Group Type
 field. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-80 Add External Modem to EPN 
5
11. Typ e 5
 in the Hold Time (min)
 field .
12. Typ e two-way
 in the Direction
 field .
13. Typ e 9600
 in the Speed
 field.
14. Typ e Full
 in the Duplex
 field .
15. Typ e async
 in the Synchronization
 field .
16. Typ e the p ort p air assig nments in the Analog
 and Digital
 fields and  
p ress 
En t e r.
Settings for Modem Connected to the Data 
Terminal Equipment (DTE)
1. Type add station next
 and press En t e r.
2. Type 2500
 in the Type
 field.
3. Typ e the p ort assig nment in the Port
 field  and  p ress 
En t e r.
Add External Modem to EPN
U.S. Robotics Model USR 33.6 EXT External 
Modem
Figure 5-33. Connect External Modem to EPN Figure Notes:
1. U.S. Rob otic s External Mod em
2. RS-232 Cable3. Exp ansion Port Network
cydfepnm KLC 100397
TERM INAL
1
2
3 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-81 Add External Modem to PPN 
5
1. Connec t an RS-232 c ab le to the modem. See Fig ure 5-33.
NOTE:
In the following  step s, a PC with Wind ows 95 or Wind ows NT 4.0 may 
b e sub stituted for the d umb  terminal. Use the Hyp erterminal 
(terminal emulation) ap p lic ation. 
2. Connec t the op p osite end  of the RS-232 c ab le to a d umb  terminal. 
3. Set the d umb  terminal to full d up lex mod e.
4. Type AT&N6
 to set the baud  rate to 9600. 
NOTE:
The mod em c onnec ts at 9600 b aud  b ut throug hp ut is at 1200 b aud .
5. Type AT & W 0
 to save the setting  into non-volatile RAM.
6. Set Switc h 5 to the OFF (up ) p osition to disab le auto answer.
7. Disc onnec t the RS-232 c ab le from the terminal and c onnec t it to the 
TERMINAL c onnec tor on the rear of the system c ab inet.
Add External Modem to PPN
U.S. Robotics Model USR 33.6 EXT External 
Modem
Figure 5-34. Connect External Modem to PPN Figure Notes:
1. U.S. Rob otic s External Mod em
2. RS-232 Cable3 . Pro c e s s o r  Po r t  N e t w o rk
cydfepnm KLC 100397
TERM INAL
1
2
3 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-82 Add External Modem to TN1648B 
5
1. Connec t an RS-232 c ab le to the modem. See Fig ure 5-34.
NOTE:
In the following  step s, a PC with Wind ows 95 or Wind ows NT 4.0 may 
b e sub stituted for the d umb  terminal. Use the Hyp erterminal 
(terminal emulation) ap p lic ation. 
2. Connec t the op p osite end  of the RS-232 c ab le to a d umb  terminal. 
3. Set the d umb  terminal to full d up lex mod e.
4. Type AT&N6
 to set the baud  rate to 9600. 
NOTE:
The mod em c onnec ts at 9600 b aud  b ut throug hp ut is at 1200 b aud .
5. Type AT & W 0
 to save the setting  into non-volatile RAM.
6. Set Switc h 5 to the OFF (up ) p osition to disab le auto answer.
7. Disc onnec t the RS-232 c ab le from the terminal and c onnec t it to the 
TERMINAL c onnec tor on the rear of the system c ab inet.
Add External Modem to TN1648B
Use a type approved external modem. 
Unpack and Inspect
1. Verify the eq uipment rec eived . See Fig ure 5-35. Ac tual eq uip ment may 
vary in ap p earanc e and  may ship  in sep arate p ac kag es.
2. See Tab le 5-21
 for a list of p art c omc od es. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-83 Add External Modem to TN1648B 
5
Figure 5-35. External Modem Pass-Thru Kit Equipment
Figure Notes
1. Pass-thru Tool
2. Mac hine Sc rew
3. Cable Tie4. Panel Ad ap ter Brac ket
5. Cab le Assemb ly
6. Cab le Tie Mount
Table 5-21. Parts List
Quantity Description Comcode
1 External mod em p ass-thru kit
Kit inc lud es: p ass-thru tool, c ab le ties, p anel 
ad ap ter brac ket, mac hine sc rews, and  c ab le tie 
mounts.848239596
1 Cab le Assemb ly H600-497
indakit2 EWS 091498
123
4
6
5 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-84 Add External Modem to TN1648B 
5
Cabinet Preparation
1. Open the front d oor.
NOTE:
Ad ministration may b e req uired  b efore removing  the c irc uit p ac k in 
the following  step .
2. Determine whic h slot will c ontain the new c irc uit p ac k. Remove the c irc uit 
p ac k or the app aratus b lank from this slot. 
3. Install the new c irc uit p ac k.
4. From the front, remove the fan c over. See Fig ure 5-36
.
Figure 5-36. Remove the Fan Cover
lcda3fop EWS 110398
ENTER
/YES ENTER
/YES NEXT
/NO NEXT
/
NO BACK
BACK
AUDIX AUDIXBOOT/
SHUTDOWN BOOT/
SHUTDOWN
ALARMS
ALARMS
EMERTR
EMERTR 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-85 Add External Modem to TN1648B 
5
Install the Pass-thru Kit 
1. Open the rear d oor.
2. Attac h the p anel ad ap ter b rac ket. See Fig ure 5-37
.
3. Insert the c ab le assemb ly. See Fi g u re  5 - 3 8
.
Figure 5-37. Attach the Panel Adapter Bracket 
prda0002 EWS 090498 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-86 Add External Modem to TN1648B 
5
Figure 5-38. Attach the Cable Assembly to the Bracket
4. Connec t the external mod em c ab le to the c ab le assemb ly.
5. Attac h the RJ45 (telep hone p lug) to the p ass-thru tool using  a tie wrap . 
See Fi g u re  5 - 3 9
. If you are using  only one RJ45, bund le the other one and  
tie wrap  it near the b od y of the c ab le assemb ly.
prda0003 EWS 090498