Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation And Test For Multi-Carrier Cabinets Manual

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-5 Access the System 
3
Connecting a PC
You c an c onnec t your PC or lap top  to the DEFINITY ECS R8si/R8c si/R8r either 
d irec tly (50 ft [ 15 m]  or less) or remotely throug h a d ata mod ule or a mod em. 
Connecting directly to the DEFINITY ECS
You c an c onnec t d irec tly from the PC if it is 50 ft (15 m) or less from the 
DEFINITY ECS. 
1. Connec t the eq uip ment as shown in Fi g u re  3 - 3
. See Tab le 3-2 for the 
c onnec tions b y p latform. 
!CAUTION:
For a DC-p owered  system, install an EIA 116A Isolator (c omc od e 
106005242) in series b etween the c ab le and  the TERM, DOT, or Terminal 
Ac tive c onnec tor.
Figure 3-3. A typical direct connection
Figure Notes
1 . D EFI N I TY EC S ( PPN  o n  R8 r )
2. 50-ft (15-m) M25A c ab le 
(RS-232)3. 9-to-25 pin ad ap ter if need ed
4. Comp uter with DSA or DNA
Table 3-2. PC connections by platform
Reliability R8r R8si R8csi
Standard Terminal Active TERM TERM
Hig h/Critic al—DOT—
cydfdr23 LJK 021800
2
31
4 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-6 Access the System 
3
Connecting remotely to the DEFINITY ECS
To c onnec t remotely to the system, you need  one of the following  p iec es of 
hard ware:
nConnec ting  throug h a data mod ule
nConnec ting  b y analog  mod em to INADS p ort
Connecting through a data module
If more than 50 ft (15 m) from the DEFINITY ECS, you c an c onnec t the PC throug h 
a data module. 
1. Connec t the eq uip ment as shown in Fi g u re  3 - 4
.
Figure 3-4. A typical remote connection using an 8400B (top) or 7400B 
(bottom) data module Figure Notes
1. DEFINITY ECS
2. Dig ital line c irc uit p ac k
3. B25A 25-p air c able
4. Main d istrib ution frame (MDF)
5. 103A or Luc ent mod ular wall jac k
6. 400B2 ad apter
7. D6AP p ower c ord (8400B+  only)8. Data module power supply
9. 7-ft (2-m) D8W mod ular cord
10. Data mod ule (8400B+  [ top ]  or 
7400B+  [ b ottom] )
11. 50-ft (15-m) M25A c able (RS-232)
12. Comp uter with DSA or DNA
cydfdr08 KLC021500
3
3
4
4
8
5
5
1
29
1
26
7
8
9
10
10
11
11
12
12 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-7 Access the System 
3
NOTE:
With a 7400A or 7400B+  data mod ule, use a 4-wire d ig ital line c irc uit p ac k. 
With the 8400B+  d ata mod ule, use a 2-wire d igital line c irc uit p ac k.
In p lac e of a 7400B+  d ata mod ule, you c an use a 7400A d ata mod ule. If 
you do, set the 7400A to DCE Mod e.
2. Wire the d ig ital line c irc uit p ac k to the wall jac k as follows:
nFor a 7400B+ , wire to the sec ond and  third pair of the wall jac k.
nFor an 8400B+ , wire to the first p air of the wall jac k.
Setting the Data Module to DCE Mode
1. Cyc le the p ower to the d ata mod ule. The unit p erforms a self test and  
displays its operating mode.
2. Observe the d isp lay.
a. If the d isp lay reads DCE mod e, p roc eed  to the next sec tion.
b . If the d isp lay reads DTE mod e, c omp lete the following  step s:
1. Remove the p ower c ord  from the unit.
2. Remove the c over from the top  rear of the unit.
3. Remove the mod e selec t c irc uit b oard  and  turn it around .
4. Rep lac e the c over.
5. Connect the power c ord.The unit performs a self test.
NOTE:
The p ower LED must b e stead y on. If the p ower LED is b linking, the d ata 
mod ule is not c ommunic ating  with the DEFINITY ECS. Chec k the wiring  at 
the MDF, wall jac ks, and  d ata mod ule.
Adding a Data Module to the Switch
1. Add the data module to the switch by entering add data-module
 number 
or add data-module next
.
2. In the Type:
 field , typ e pdm
 and press 
En te r.
3. In the Port:
 field , typ e the loc ation of the d ig ital line c irc uit p ac k 
connec ted to the data module (for example 01A1503).
4. If system ac c ess p orts and  hunt g roup s have not b een set up , set them 
up . Refer to DEFINITY ECS Release 8 Ad ministrator’s Guid e. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-8 Access the System 
3
Testing Hardware Connections
In the following  tab le, find  your d ata mod ule and  follow the instruc tions for testing  
and  troub leshooting  it.
.
Setting the Data Module Operating Mode
1. Connec t an RS-232 c ab le from the DSA/DNA c omp uter to the d ata 
mod ule. If you are using  an 8400B+ , c onnec t the DSA/DNA c omp uter to 
the data module using the supplied adapter cable.
2. Using  a terminal emulator, c onnec t to the serial p ort to whic h the d ata 
mod ule is c onnec ted , and  set the emulation to vt100 mod e.
3. Type AT
 at the p romp t and  p ress 
En t e r.The d ata mod ule should  return an 
OK. If it d oes not, b e sure that a stand ard RS-232 or EIA-232 c ab le is 
connec ted (not a null modem c able).
4. Set the operating mode as described in the following table.
5. Disc onnec t the terminal from the d ata mod ule and  rec onnec t the d ata 
mod ule to the system c ab ling . Ty p e  o f  
Data Module How to Test and Troubleshoot
8400B+ The red  LED should b e stead y on. If the red  and  g reen LEDs 
are b linking , the unit is not c ommunic ating  with the DEFINITY 
ECS. Chec k the wiring  at the MDF, wall jac k, and  the 8400B+ . 
7400B+ The Power and  TR LEDs should  b e stead y on. If the Power 
and  Data LEDs are b linking , the unit is not c ommunic ating  with 
the DEFINITY ECS. Chec k the wiring  at the MDF, wall jac k, 
and  the 7400B+ . 
7400A Set the 7400A to DCE mod e. The Power LED must b e stead y 
on. The DTR, DSR, DCD, RTS, and  CTS setting s must b e 
hig hlig hted in the d isp lay. If the Power LED is b linking , the 
d ata mod ule is not c ommunic ating  with the DEFINITY ECS. 
Chec k the wiring  at the MDF, wall jac k, and  7400A.
Ty p e  o f  
Data Module How to set the operating mode
8400B+ Typ e AT&F
 and press 
En t e r. Typ e ATS24=1
 and press 
En te r. Type AT&WØ
 and press En t e r to save the operating 
mode into non-volatile RAM.
7400A
7400B+Ty p e  AT&F
 and press 
En t e r. Typ e AT&WØ
 and press 
En te r to save the op erating  mod e into non-volatile RAM. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-9 Access the System 
3
Setting the 7400B+ Options
1. Set the DIP switc hes for the 7400B+  using  Tab le 3-3. The DIP switc hes are 
loc ated  insid e the unit. To ac c ess them
a. Remove the p ower c ord  from the unit.
b . Remove the c over from the top  rear of the unit.
c . Set the d ip  switc hes.
d . Rep lac e the c over.
e. Connect the power c ord.The unit performs a self test.
2. If any switc hes were set in step  1, c yc le the p ower to the d ata mod ule so 
that the firmware c an read  the new switc h setting s.
Connecting by analog modem to INADS port
You c an c onnec t a PC to the DEFINITY ECS throug h a mod em.
Table 3-3. DIP Switch Settings (7400B+)
Option DIP Switch Setting
No Telep hone Connec ted 1 On
Data Metering 5 Off
Sup p ress Touc h-tone/Dial Tone 6 Off
Sp eakerp hone Disab le/Enab le 7 Off
Busyout on Loc al Loop 8 Off
Unused  DIP Switc hes 2, 3, and  4 Off 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-10 Access the System 
3
1. Connec t the eq uip ment as shown in Fi g u re  3 - 5.
Figure 3-5. A typical remote connection through a modem to access a remote 
DEFINITY ECS
Follow these step s to c onnec t to the DEFINITY ECS through a mod em.
1. Connec t the c omp uter to the mod em.
2. Connec t an analog  telephone line to the left most analog -line p ort on the 
mod em. 
3.Make sure that the mod em’s DIP switc hes are set as shown in Ta b l e  3 - 4
. Figure Notes
1. Comp uter with DSA or DNA
2. 50-ft (15-m) M25A c ab le (RS-232—
9-25 p in ad ap ter if need ed )
3. Analog  mod em
4. 7-ft (2-m) D2W mod ular c ord
5. 103A or Luc ent mod ular wall jac k
6. Main d istrib ution frame (MDF)7. Analog line circuit pack
8. Analog  trunk c irc uit p ac k
Pac ket d ata line (R8r)
Data line (R8r)
9. DEFINITY ECS
10. B25A c ab le
11. Analog  line
cydr0031 LJK 021800
1
2
3
11
4
5
78
9
1010
6 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-11 Access the System 
3
4. Plug  the mod em into an AC p ower outlet.
5. Turn on the modem.
6. Set the following  p ort setting s:
Table 3-4. U.S. Robotics Modem Dip Switch Settings
Dip 
Switch Setting Description
1UP
DOWNData Terminal Read y normal
Data Terminal Ready override
2UP
DOWNVe r b a l  r e s u lt  c o d e s
Numeric result codes
3UP
DOWNSuppress result codes
Display result codes
4UP
DOWNEc ho offline c ommand s
No echo, offline commands
5UP
DOWNAuto answer on first ring or higher if specified in 
NVRAM
Auto answer off
6UP
DOWNCarrier d etec t normal
Carrier detect override
7UP
DOWNLoad  NVRAM d efaults
Load factory defaults
8UP
DOWNDumb  mod e
Smart mode
Baud  rate 9600
Data b its 8
Pa r it y N o n e
Stop  b its 1
Flow c ontrol hard ware 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-12 Activate the System 
3
Activate the System
Instruc tions are p rovid ed  to ac tivate Release 8 and  later systems. To ac tivate a 
G3V4 and  earlier system, refer to DEFINITY Communic ations System Generic  3 
Installation and  Test.
NOTE:
To p revent unnec essary troub le tic kets, d o not enab le the system alarms 
(Alarm Orig ination feature) until all installation and  ad ministration 
p roc ed ures are c omp leted .
!CAUTION:
It may be nec essary to reseat c irc uit p ac ks. To prevent d amag e from static  
elec tric ity, always wear an Elec tromag netic  Comp atib ility (EMC) wrist strap  
(c omc od e 900698226) when hand ling  all system c omp onents.
Install Translation Card (Release 8si in MCC 
Cabinet)
1. Insert the translation c ard  into the TN794 Network Control c irc uit p ac k in 
the direction indicated by the arrow on the label.
Install Removable Media (Release 8r in MCC 
Cabinet)
2. Insert the formatted  removab le med ia, lab el fac ing  left, into the op tic al 
drive (see Fi g u re  3 - 6
). 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-13 Activate the System 
3
Figure 3-6. TN2211 Optical Drive
NOTE:
Make sure the formatted removab le med ia is not write-p rotec ted 
(see Fig ure 3-7
) b efore plac ing  it into the op tic al d rive.
Figure 3-7. Make sure the disk is not write protected Figure Notes
1. Not write protec ted 2. Write p rotec ted
Red
Green
Yellow
fpdf2211 KLC 010600TN2211 OPTICAL DRIVE
h1dfdsk KLC 112499
12 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Accessing and Activating the System 
3-14 Activate the System 
3
Power Up the System
AC-Powered System
1. Set the c irc uit breakers on the AC p ower p anel to ON. If the system is hig h 
or c ritic al reliab ility, p ower-up the EPN c ab inet first, then the PPN c ab inet. 
Always p ower up the PPN c ab inet last.
2. Set the c ab inet c irc uit breakers to ON. This starts the system initialization 
and  test. All red  LEDs on the c irc uit pac ks go on and  then off. 
3. Skip  to ‘‘
Verify Messag es on Terminal’’.
DC-Powered System
1. At the DC Battery Cab inet (if installed ), set the c irc uit breaker to ON.
2. At the DC Power Cab inet, set the c irc uit b reaker(s) on the rec tifiers ON. 
This starts the system initialization and  test. Some red  LEDs may b e on b ut 
are turned  off b y other p roc ed ures in this c hap ter. 
3. If the system is hig h or c ritic al reliab ility, p ower-up  the EPN c ab inet first, 
then the PPN c ab inet. Always p ower up  the PPN c abinet last.
Verify Messages on Terminal
1. After several minutes, verify all tests p ass. Sc reen 3-1 d isp lays the sc reen 
c ontents of a typ ic al Release 8r system with 3 memory c irc uit p ac ks. The 
Release 8si system sc reen is similar.
NOTE:
If any of the terminal messag es ind ic ate a test has failed  or if the messag e 
“spe down mode
”  is d isp layed , refer to D EFINITY En terp ris e 
Communic ations Server Release 8 Maintenanc e for R8r, or DEFINITY 
Enterprise Communic ations Server Release 8 Maintenanc e for R8si, to 
c lear the troub le.