Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation And Test For Multi-Carrier Cabinets Manual

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-67 List of Circuit Packs 
5
TN436B Direc t Inward  Dialing  Trunk (Australia) Port
TN437 Tie Trunk (Australia, rep lac ed  b y TN760D) Port
TN438B Central Offic e Trunk (Australia) Port
TN439 Tie Trunk (Australia and  Jap an) Port
TN447 Central Offic e Trunk Port
TN457 Sp eec h Synthesizer, British Eng lish Servic e
TN458 Tie Trunk for the United Kingdom (replaced by 
TN760D)Po r t
TN459B Direc t Inward  Dialing  Trunk for the United King d om Port
TN464C/D/E/F DS1 Interfac e - T1, 24 Channel - E1, 32 Channel Port
TN465/B/C Central Offic e Trunk (Multi-Country, 16-kHz PPM) Port
TN467 Analog  Line for the United  King d om and  Australia 
(rep lac ed  b y TN2183)Po r t
TN468BAnalog  Line for the United  King d om and  Australia 
(rep lac ed  b y TN2183) (16 p orts)Po r t
TN479 Analog  Line 
(16 ports)Po r t
TN497 Tie Trunk - Italy Port
TN553 Pac ket Data Line Port
TN556/B/C/D ISDN Line (12-BRI-S-NT) Port
TN570/B/C Exp ansion Interfac e Port
TN572 Switc h-Node Cloc k for r only Control
TN573B Switch-Node Interface for r only Control
TN 5 7 4DS1 Converter (rep lac ed by TN1654) (G3rV2 and  
later) Po r t
TN722B DS1 Tie Trunk (rep lac ed  b y TN767B/C/D/E) (24 p orts) Trunk
TN725B Sp eec h Synthesizer, United  States Eng lishSe r v ic e
TN726B Data Line (8 p orts) Line
TN735 MET Line (4 p orts) Line
TN 7 4 2Analog  Line (8 p orts) (rep lac ed  b y TN746B) Line
Table 5-19. Circuit Packs and Circuit Modules  — Continued
Apparatus 
Code Name Type
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-68 List of Circuit Packs 
5
TN744B/C/DCall Classifier Tone Detec tor, Multi-CountrySe r v ic e
TN746B Analog  Line (US and  Canad a Offer A Only) (16 p orts) Line
TN747B Central Offic e Trunk(8) Trunk
TN748B/C/D Tone Detec tor (rep lac ed  b y TN2182B) Se r v ic e
TN750B/C Announc ementSe r v ic e
TN753B Direc t Inward  Dialing  Trunk (8 p orts) Trunk
TN753/B Direc t Inward  Dialing  Trunk Port
TN754/B/C Dig ital Line 4-Wire DCP Port
TN755/B Neon Power Unit Power
TN 7 5 6Tone Detec tor/Generator (XE) (rep lac ed  b y TN2182B) Servic e
TN758 Pooled Modem (2 p orts) Port
TN760D/E Tie Trunk (4 p orts) Trunk
TN762B Hyb rid  Line (8 p orts) Line
TN763B/C/D Auxiliary Trunk (4 ports) Trunk
TN767B/C/D/E DS1 Interfac e - T1, 24 Channel Port
TN768 Tone-Cloc k (rep lac ed  b y TN2182B) Control
TN769 Analog  Line (8 p orts) (Neon) Line
TN771B/C/D Maintenanc e Test  Servic e
TN773 Proc essor Control
TN775/B/C Maintenanc e (EPN) Servic e
TN776 Exp ansion Interfac e (si only) Port
TN780 Tone Cloc k (all mod els exc ep t c si, Stratum 3) Control
TN787F/G/H/J/
KMultimed ia Interfac e Servic e
TN788B Multimed ia Voic e Cond itioner  Servic e
TN789 Rad io Controller Control
TN790B Processor (R7 si and later)  Control
TN791 Analog  Guest Line (16 Port) Line
Table 5-19. Circuit Packs and Circuit Modules  — Continued
Apparatus 
Code Name Type
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-69 List of Circuit Packs 
5
TN792 Duplic ation Interfac e (for TN790B Proc essor Circ uit 
Pac ks, si only) Control
TN793B 24-Port Analog  Line w/CID Line
TN794 Network Control/Pac ket Interfac e for si onlyControl
TN797B Analog  Trunk and  Line Comb o Port
TN799B Control-LAN (C-LAN) Port
TN800 Multi-Ap p lic ation Platform for DEFINITY (MAPD) Port
TN801 Multi-Ap p lic ation Platform for DEFINITY (MAPD) Port
TN802B IP Interfac e Assemb ly Port
TN1648/B System Ac c ess/Maintenanc e (SYSAM) Control
TN1650BMemory (32MB) for r only Control
TN1654 DS1 Converter - T1, 24 Channel/E1, 32 Channel Port
TN1655 Pac ket Interfac e Control
TN1657 Disk Drive Control
TN2135 Analog  Line Port
TN2136 Dig ital Line 2-Wire DCP Port
TN2138 Central Offic e Trunk (Italy, Loop  Start) Port
TN2139 Direc t Inward  Dialing  Trunk (Italy) Port
TN2140/B Tie Trunk (Hung ary, Italy) Port
TN2144 Analog  Line (The Netherlands, rep lac ed  b y TN2183) 
(16 p ort)Po r t
TN2146 Direc t Inward  Dialing  trunk (Belg ium and  The 
Netherland s)Po r t
TN2147/C Central Offic e Trunk (without PPM, rep lac es TN447) Port
TN2149Analog  Line for Belg ium (rep lac ed  b y TN2183) (16 
port)Po r t
TN2180 Analog  Line Port
TN2181 Dig ital Line (16-p orts DCP-2-Wire) Port
TN2182/B Tone-Cloc k -Tone Detec tor and  Call Classifier Control
Table 5-19. Circuit Packs and Circuit Modules  — Continued
Apparatus 
Code Name Type
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-70 List of Circuit Packs 
5
TN2183 Analog  Line, Multi Country with DSLACPo r t
TN2184 DIOD Trunk (Germany) Port
TN2185B ISDN (4-Wire S/T-TE Interfac e, 8 p orts) Port
TN2198 ISDN Line (4-Wire BRI-U-NT, 8 p orts) Port
TN2199 Central Offic e Trunk (Russia) Port
TN2202 50-Hz Ring  Generator (Franc e) Power
TN2207 DS1 Interfac e - T1, 24 Channel - E1, 32 Channel Port
TN2209 Tie Trunk (Russia) Port
TN2210 Tone Generator
 (1780 Hz)Se r v ic e
TN2211 Op tic al Drive 
(replaces TN1656)Control
TN2214B Dig ital Line, 24-Port, 2-Wire DCP - Categ ory B Port
TN2215 Analog  Line, 16-Port, 2-Wire - Categ ory B Port
TN2224/B Digital Line, 24-Port, 2-Wire DCP Port
TN2301 Log ic  Switc h (for r only, Survivab le Remote EPN) Switc h
TN2305 DEFINITY ATM Interfac e (Multi-Mode fiber, Port 
Network Connec tivity, CES Trunk)Po r t
TN 2 3 0 6 D EFI N I TY A TM  I n t e rf a c e  (Si n g l e -M o d e  Fi b e r ,  Po rt  
Network Connec tivity, CES Trunk))Po r t
TN2313 DS1 Interfac e  Port
TN2464 DS1 Interfac e - T1, 24 Channel - E1, 32 Channel Port
TN2793 Analog  Line 24-Port - Categ ory B Port
UN331B Processor Control
UN332C MSS Network Control (for r only; used  with the 
TN2211 Op tic al Drive)Control
Table 5-19. Circuit Packs and Circuit Modules  — Continued
Apparatus 
Code Name Type
Continued on next page 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-71 Add CO, FX, WATS, and PCOL 
5
Add CO, FX, WATS, and PCOL
Requirements
Each Central Office (CO), Foreign Exchange (FX), Wide Area 
Telecommunications Service (WATS), or Personal Central Office Line (PCOL) 
trunk is connected to 1 port of either an 8-port TN747 or to 1 of an assortment of 
non-United States CO Trunk circuit packs. 
Installation
1. See ‘‘Off-Premises Station Wiring’’ on p ag e 5-32 and  install a CO trunk 
c irc uit p ac k in the assigned  c arrier slot (if an ad d itional c irc uit p ac k is 
req uired ).
2. Ad minister the Trunk Group  sc reens listed  und er CO, FX, WATS, or PCOL 
Trunk Group  in DEFINITY Enterp rise Communic ations Server Release 8 
Ad ministrator’s Guid e.
3. Determine the p ort assig nment of the trunk from Trunk Group  sc reen. For 
examp le:
Add DID Trunks
Requirements
Each Direct Inward Dial (DID) trunk connects to 1 port of an 8-port TN753 or to 1 
of an assortment of non-United States DID trunk circuit packs.
Installation
1. Determine the p ort assig nment of the trunk from Trunk Group  form. For 
examp le:3 A 07 01
Cab inet
(Port Network)Carrier Slot 
NumberPo r t  
Numb er
3 A 07 01
Cab inet
(Port Network)Carrier Slot 
NumberPo r t  
Numb er 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-72 Add Tie Trunks 
5
2. See‘‘Off-Premises Station Wiring’’ on p age 5-32 and  install a DID trunk 
c irc uit p ac k in assigned  c arrier slot (if an ad d itional c irc uit p ac k is 
req uired ).
3. Ad minister DID Trunk Group  sc reens in DEFINITY Enterp rise 
Communic ations Server Release 8 Ad ministrator’s Guid e.
Add Tie Trunks
Requirements
Each tie trunk connects to 1 port of a 4-port TN760 or to an assortment of 
non-United States tie trunk circuit packs.
Installation
1. Determine the p ort assig nment of the trunk from Trunk Group  form
2. Install a TN760 or a non-United  States tie trunk c irc uit p ac k in the 
assig ned  c arrier slot (if an add itional c irc uit pac k is req uired ).
3. For c ustomer-owned  (not leased ) tie-trunk fac ilities (suc h as c amp us 
environments), TN760 c irc uit p ac ks p rovid e sig naling  c ap ab ilities b eyond  
those sp ec ified  b y the ind ustry-wid e E & M stand ard . Use Fig ure 5-32
 and  
Tab le 5-20
 to c hoose the p referred  sig naling  format, set switc hes on the 
TN760 c irc uit p ac k, and  ad minister the p ort.
4.Ad minister forms listed  under “ Tie Trunk Group ”  in DEFINITY Enterp rise 
Communic ations Server Release 8 Ad ministrator’s Guid e. 3 A 07 01
Cab inet
(Port Network)Carrier Slot 
NumberPo r t  
Numb er 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-73 Add Tie Trunks 
5
Figure 5-32. Tie Trunk Circuit Packs (Component Side)
Table 5-20. Tie Trunk Option Switch Settings and Administration
Installation Situation Preferred Signaling FormatE&M/SMPLX 
SwitchProt/Unprot 
SwitchAdministered
Port
Circumstance To System Far-End
Co-Loc ated DEFINITY E&M Typ e 1 E&M Typ e 1 E&M Unp rotec ted Typ e 1
Comp atib le Stand ard Compatible
Inter-Build ing DEFINITY Protec ted 
Typ e 1Protec ted 
Typ e 1E&M Pro te c t e d Typ e  1
Comp atib le Stand ard 
Pl u sCompatible
Protec tion
Unit
Co-Loc ated Net 
IntegratedE&M Typ e 1 Any PBX E&M Unp rotec ted Typ e 1
Stand ard
UNPROT
PROTSMPLX
E&M
SMPLX
E&MSMPLX
E&MSMPLX
E&M4 3 2 1
PORT 4  PORT 3  PORT 2  PORT 1 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-74 Add DS1 Tie and OPS 
5
Add DS1 Tie and OPS
The TN722B DS1 Tie Trunk, TN767C (or later) DS1 Interface, and TN464C DS1 
Interface circuit packs provide connections to a 1.544 Mbps or 2.08 Mbps DS1 
facility as 24 independent 64 kbps trunks. When upgrading from a TN722 to a 
TN767C:
1. Remove all TN722 trunk memb ers from affec ted  trunk g roup s.
2. Type remove ds1 PCSS
 (PCSS is the slot containing the TN722).
3. Remove the TN722 c irc uit p ac k.
4. Put the TN767C c irc uit p ac k into the same slot.
5. Wait until the red  LED g oes off. The hard ware tests take 12 to 20 sec ond s 
to run. When the red  LED g oes off, the tests have c omp leted .
6. If the red  LED stays on, reseat the b oard and  rep eat this step .
7. Type add ds1 PCSS
.
8. Continue with ap p rop riate p roc ed ures to set up  memb ers of trunk g roups.
Service Interruption
Adding DS1 tie-trunk service may require a service interruption; notify the 
customer in advance as to when the addition will be carried out.
Disable Scheduled Maintenance and Alarm 
Origination to INADS
1. To p revent sc hed uled  d aily maintenanc e from interfering  with the up d ate 
or up g rad e, typ e change system-parameters maintenance
 and  p ress 
En t e r.
2. If sc heduled maintenanc e has b eg un, set the Stop Time
 field  to 1 minute 
after the c urrent time.
or
If sc hed uled  maintenanc e has not
 b eg un, set the Start Time
 field  to a 
time after the upgrade is completed. For example, if you start the upgrade 
at 8:00 p .m. and  the up g rad e takes 90 minutes, set the Start Time
 field  
to 21:30.
!CAUTION:
If you d o not d isab le Alarm Orig ination, the system may g enerate 
alarms, resulting  in unnec essary troub le tic kets. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-75 Add DS1 Tie and OPS 
5
3. Type neither 
in the Alarm Origination to OSS Numbers 
field and 
p ress 
En t e r .
NOTE:
For some software load s, set the Alarm Origination 
Activated
 field  to n 
and 
set the Cleared Alarm Notification 
and  Restart Notification
 fields to disable
 or n
 before 
pressing 
En t e r. 
Save Translations
1. If the system is hig h or c ritic al reliab ility, typ e status system 1
 and press 
En t e r  to verify that the system is in the “ ac tive/stand b y”  mode.
2. Type save translation
 and press 
En te r. This instruc ts the system to take all 
translation information in memory and  write it to the translation c ard  or 
removab le med ia.
3. If the system c ontains a TN750/B Announc ement c irc uit p ac k, type 
display announcements
 and  p ress 
En t e r. If ad ministered  rec orded  
announc ements are listed , typ e list configuration software-version
 
p ress 
En t e r . Chec k Pag e 2 of this form to see when the announc ements 
were last saved. To save the c urrent announc ements, typ e save 
announcements
 and  p ress 
En te r .
Shut Down DEFINITY LAN Gateway System
!WARNING:
Neg lec ting  to shut d own a DEFINITY LAN Gateway assemb ly b efore 
p owering  d own the system c ab inet where it resides c an d amage the LAN 
Gateway disk.
!CAUTION:
Save the system p arameters if you p lan to reuse the c urrent system.
1. Log  onto the DEFINITY LAN Gateway.
2. When the main menu ap p ears, selec t Maintenance.
3. Select Reset System
 from the Maintenance
 menu.
4. Select Shutdown
 from the Reset System
 menu. 
						

							DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-76 Add DS1 Tie and OPS 
5
Shut Down DEFINITY AUDIX System
!WARNING:
Neg lec ting  to shut d own an AUDIX assemb ly b efore p owering down the 
system c ab inet where it resides c an d amage the AUDIX d isk.
1. If a DEFINITY AUDIX resid es in the system to be up g rad ed , shut d own the 
AUDIX assemb ly and  allow the d isk to c omp letely sp in d own.
Power Down System
NOTE:
Power d own the PPN only if the existing  Tone-Cloc k is b eing  rep lac ed  in a 
standard  reliab ility system.
1. At the PPN, set the main c irc uit b reaker to OFF.
2. At eac h EPN, set the main c irc uit breaker to OFF.
Add Circuit Packs
1. Determine the port assignments of the circuit packs to be added.
2. Install the TN722B DS1 Tie Trunk, the TN767C DS1 Interfac e, or TN464C 
DS1 Interfac e c irc uit p ac k in assig ned  c arrier slot.
3. Rep lac e an existing  TN756 Tone Detec tor/Generator c irc uit p ac k with:
a. TN768, TN780, or a non-United  States TN419B Tone-Cloc k
b . TN748B or a non-United States TN420B Tone Detec tor
Install Cables
Install H600-307 cable from the cabinet to a Channel Service Unit (CSU) and 
install cables from the CSU to the MDF as required.
Power Up System
1. At eac h EPN, set the main c irc uit breaker to ON.
2. At the PPN, set the main c irc uit b reaker to ON.
3. The system p erforms the level 4 reb ooting  p roc ess, load ing  the system 
translations from the translation c ard  or removab le med ia. Reb ooting 
takes 8 to 11 minutes.