GE Logiq P5 Service Manual

							GE HEALTHCARE
DIRECTION 5394141, REVISION 1 LOGIQ™ P5 SERVICE MANUAL
Section 3-4 - Preparing for Installation 3-21
3-6-5 Video Specification
Video specifications may be needed to be able to connect the VCR or DVD Video Recorder to the 
LOGIQ™ P5/A5/A5Pro.
Table 3-9    Video Specifications
Timing ParameterNTSCPAL
640x480
60Hz800x60060Hz800x60075Hz1024x768 60Hz
Horizontal Rate [kHz] 60.02 31.25 31.47 37.88 46.88 48.36
Horizontal Period [µ s]16.66 32.00 31.78 26.40 21.33 20.68
Pixel Clock [MHz] 78.75 29.50 24.55 40.00 49.50 65.00
H Blank Width  [µs] 3.66 5.97 5.706.405.17 4.92
H Sync Width  [µs] 1.22 2.34 2.363.201.62 2.09
H Front Porch  [µs] 0.20 0.75 0.731.000.32 0.37
Active Horizontal Period  [µs] 13.00 26.03 26.07 20.00 16.16 15.75
Vertical Rate [Hz] 75.03 50.00 59.94 60.32 75.00 60.00
Vertical Period [ms] 13.33 20.00 16.68 16.58 13.33 16.67
V Sync Width [lines=ms] 32=0.53 49=1.57 45=1.43 28=0.74 25=0.53 38=0.79
V Front Porch  [lines=µ s] 3=50.00 5=160.00 6=190.70 4=105.60 3=64.00 6=124.10
Equalization Gate  [lines= µs] 1=16.66 5=160.0 6=190.7 1=26.4 1=21.3 3=62.00
Lines: Field/Frame 800 625/625 525/525 628 625806
Active Lines/Frame 768576 480600600768 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL 
3-22 Section 3-4 - Preparing for Installation
3-6-6 Setting VCR (Mitsubishi MD3000) USB Interface
1.) Turn off the Power of the VCR.
2.) Open the rear panel of the VCR.
3.) Set dip switches. Off 1~6 pins, On 7 pin, and Off 8 pin.
NOTE: 7 Pin ON = USB Interface, OFF = RS232C Interface.
Figure 3-15   Setting VCR USB Interface 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION 1 LOGIQ™ P5 SERVICE MANUAL
Section 3-8 - Software/Option Configuration 3-23
Section 3-7
Available Probes
See Specifications in the LOGIQ™ P5/A5/A5Pro User Manual for probes and intended use.
See Chapter 9 , for part numbers to be used when ordering new or replacement probes.
Section 3-8
Software/Option Configuration
refer to the LOGIQ™ P5/A5/A5Pro Basic User Manual, Chapter 16, Customizing Your System for 
information on conf iguring items like Hospital,  Department, Language, Units (of measure), Date, Time 
and Date Format.
For information on configuring Software Options,  refer to the LOGIQ™ P5/A5/A5Pro Basic User 
Manual, Chapter 16, Customizing Your System.
For information on configuring DI COM Connectivity, refer to the LOGIQ™ P5/A5/A5Pro Basic User 
Manual, Chapter 16, Customizing Your System. 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL 
3-24 Section 3-8 - Software/Option Configuration
Section 3-9
Connectivity Installation Worksheet
Site System Information
Services (Destination Devices) TCP/IP Settings
Device Type
Manufacturer
Name
IP Address Port
AE Title
1
2
3
4
5
6
7
8
9
10
11
12
Name - AE Title:
Dept:
LOGIQ SN:Type:
Floor:
Room:
REV:
Comments:
CONTACT INFORMATION
Name Title
PhoneE-Mail Address
Site:
IP Settings
IP Address:
Subnet Mask:
Default Gateway:
Remote Archive Setup
Remote Archive IP:
Remote Archive Name: 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION 1 LOGIQ™ P5 SERVICE MANUAL
Section 3-11 - Loading Base System Software 3-25
Section 3-10
Insite IP Address Configuration
This information needed to facilitate the OnLine Center engineers in connecting to the system is found 
in the InSite Installation Manual.
Section 3-11
Loading Base System Software
3-11-1 Loading Base system Software
For more information on  loading base system software, refer to Chapter 8.
Section 3-12
Warnings
3-12-1 Warnings
3-12-1-1 USB HDD
External USB type Hard drive may be used to back up the data. But not all kinds of USB type can 
be supported.
Never use USB types which requ ire additional power source.
3-12-1-2 Starting Echoloader in Maintenance mode If Echoloader never started once, starting Echoloader  in the maintenance mode will not work. In 
other words, in order to be able to start Echoloa der in maintenace mode, Echoloader should have 
been started at least once. 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL 
3-26 Section 3-12 - Warnings
Section 3-13
Paperwork
NOTE: During and after installation, the documentation  (i.e. User Manuals, Installation Manuals...) for the 
peripheral units must be ke pt as part of the original system do cumentation. This will ensure that all 
relevant safety and user information is available during the operation and service of the complete 
system.
3-13-1 Product Locator Installation
NOTE: The Product Locator Installation Card shown  may not be same as the provided Product Locator 
card.
3-13-2 User Manual(s)
Check that the correct User Manual(s) for the syst em and software revision, is included with the 
installation. Specific language versions of the User  Manual may also be available. Check with your GE 
Sales Representative for availability.
3-13-2-1 Reference off-board peripherals and options None. Figure 3-16   Product Locator Installation Card 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION 1 LOGIQ™ P5 SERVICE MANUAL
Section 4-1 - Overview 4 - 1
Chapter 4
Functional Checks
Section 4-1
Overview
4-1-1 Purpose of Chapter 4
This chapter provides procedures for quickly checking major functions of the LOGIQ™ P5/A5/A5Pro 
scanner diagnostics by using the built-in service software, and power supply adjustments.
Section 4-2
Required Equipment
• An empty (blank) DVD-R or CD-R Disk.
• At least one transducer. Table 4-1    Contents in Chapter 4
SectionDescriptionPage Number
4-1 Overview 4-1
4-2 Required Equipment 4-1
4-3 General Procedure 4-2
4-4 Software Configuration Checks 4-25
4-5 Peripheral Checks 4-26
4-6 Monitor Function Checks 4-27
4-7 Keyboard Function Checks 4-29
4-8 Mechanical Function Checks 4-34
4-9 Board Function Checks 4-41
4-10 Site Log 4-54 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL 
4 - 2 Section 4-2 - Required Equipment
Section 4-3
General Procedure
4-3-1 Power On/Boot Up
NOTE: After turning off the system, wait at least ten seconds before turning it on again. The system 
may not be able to boot if power is recycled too quickly.
4-3-1-1 Scanner Power On 1.) Connect the Main Power cable to an appropriate mains power outlet.
2.) Switch ON the Main Circuit Breaker at the rear of the System.
When power is applied to the Scanner, and the Rear  Circuit breaker is turned ON, Power is distributed 
to the DC Power supply unit and power control  assy in the AC power assy. When the Power ON/OFF 
key is pressed once, the DC power supply is enab led and feed each DC power to board assemblies. 
and system run the software 
CAUTIONSYSTEM REQUIRES ALL COVERS
Operate this unit only when all board covers and frame panels are securely in place. The 
covers are required for safe operation, good system performance and cooling purposes.
NOTICELockout/Tagout Requirements (For USA only)
Follow OSHA Lockout/Tagout requirements by ensuring you are in total control of the Power Cable 
on the system.
Figure 4-1   Circuit Breaker
SignedDate
TA G 
& LOCKOUT 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION 1 LOGIQ™ P5 SERVICE MANUAL
Section 4-2 - Required Equipment 4 - 3
4-3-1-1              Scanner Power On (cont’d)
3.) Press the  ON/OFF 
key at the front of the System once.
Figure 4-2   Power On/Off  Standby Switch Location 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL 
4 - 4 Section 4-2 - Required Equipment
4-3-2 Power Off / Shutdown
NOTE: After turning off a system, wait at least ten seco nds before turning it on again. The system may not be 
able to boot if power is recycled too quickly.
4-3-2-1 Scanner Shutdown 1.) Press the On/Off  Key at the front of the System once to display the SYSTEM - EXIT menu.
2.) Select Shutdown from the SYSTEM - EXIT menu.
4-3-2-2 Switch off the System 1.) Switch OFF the Circuit Breake r at the back of the scanner.
2.) Unplug the power cord if necessary. For ex ample : Servicing or relocating the scanner.
Figure 4-3   System Exit Menu for Power Down