GE Logiq P5 Service Manual

							GE HEALTHCARE
DIRECTION 5394141, REVISION 1 LOGIQ™ P5 SERVICE MANUAL
Section 3-1 - Overview 3-1
Chapter 3
Installation
Section 3-1
Overview
3-1-1 Purpose of Chapter 3
This chapter contains information needed to install the unit. Included are references to a procedure that 
describes how to receive and unpack the equipment and how to file a damage or loss claim.
How to prepare the facility and unit of the actual installation, and how to check a nd test the unit, probes, 
and external peripherals for electrical safety are incl uded in this procedure. Also included in this section 
are guidelines for transporting the unit to a new site.
Table 3-1    Contents in Chapter 3
SectionDescriptionPage Number
3-1 Overview 3-1
3-2 Installation Reminders 3-2
3-3 Receiving and Unpacking the Equipment 3-4
3-4 Preparing for Installation 3-10
3-5 Completing the Installation 3-11
3-6 System Configuration 3-16
3-7 Available Probes 3-23
3-8 Software/Option Configuration 3-23
3-9 Connectivity Installation Worksheet 3-24
3-10 Insite IP Address Configuration 3-25
3-11 Loading Base System Software 3-25
3-12 Warnings 3-25
3-13 Paperwork 3-26 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL 
3-2 Section 3-1 - Overview
Section 3-2
Installation Reminders
3-2-1 Average Installation Time
The LOGIQ™ P5/A5/A5Pro has been designed to be installed and checked out by an experienced 
service technician in approximately four hours. LOGIQ™ P5/A5/A5Pro consoles with optional 
equipment may take slightly longer.
3-2-2 Installation Warnings
1.) Since the LOGIQ™ P5/A5/A5Pro weighs approximat ely 75 kg.(165 lb.) without options, preferably 
two people should unpack it. Two people are also pref erable for installing any additional bulky items.
2.) There are no operator serviceable components. To prevent shock, do not remove any covers or  panels. Should problems or malfunctions occur,  unplug the power cord. Only qualified service 
personnel should carry out servicing and troubleshooting.
NOTE: For information regarding packing labels, refer to  LABELS ON PACKAGE.
3.) After being transported, the unit may be very co ld or hot. If this is the case, allow the unit to 
acclimate before you turn it on. It requires one hour for each 2.5 °C increment its temperature is 
below 10 °C or above 30 °C.
Table 3-2    Average Installation Time
DescriptionAverage Installation TimeComments
Unpacking the scanner
0.5 hour
Scanner wo/options 0.5 hour
Dependant on the configuration that is required
DICOM Option 0.5 hour
Dependant on the amount of configuration
InSite Option0.5 hour
CAUTIONEquipment damage possibility. Turning the system  on without acclimation after arriving at site 
may cause the system to be damaged.
Table 3-3    Acclimation Time
° C60 55 50 45 40 35 30 25 20 15 10 5 0 -5 -10 -15 -20 -25 -30 -35 -40
°F140 131 122 113 104 96 86 77 68 59 50 41 32 23 14 5 -4 -13 -22 -31 -40
hrs864200000002468101214161820 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION 1 LOGIQ™ P5 SERVICE MANUAL
Section 3-1 - Overview 3-3
3-2-3 Safety Reminders
DANGERWHEN USING ANY TEST INSTRUMENT THAT IS CAPABLE OF OPENING THE 
AC GROUND LINE (I.E., METER’S GROU N D  S W I T C H  I S  OPEN), DON’T TOUCH 
THE UNIT!
CAUTIONTwo people should unpack the unit because of  its weight. Two people are required whenever 
a part weighing 19kg (35 lb.)  or more must be lifted.
CAUTIONIf the unit is very cold or hot, do not turn on its power until it has had a chance to acclimate 
to its operating environment. 
CAUTIONTo prevent electrical shock, connect the unit  to a properly grounded power outlet. Do not use 
a three to two prong adapter. This defeats safety grounding.
CAUTIONDo NOT wear the ESD wrist strap when you work on live circuits and more than 30 V peak is 
present.
CAUTIONDo not use a 20 Amp to 15 Amp adapter on the 120 Vac unit’s power cord. This unit requires 
a dedicated 20 A circuit and can have a 15A plug if the on board peripherals do not cause the 
unit to draw more than 14.0 amps.
CAUTIONDo not operate this unit unless all board cove rs and frame panels are securely in place. 
System performance and cooling require this.
CAUTIONOPERATOR MANUAL(S) 
The User Manual(s) should be fully read and understood before operating the LOGIQ™ P5/
A5/A5Pro and kept near the unit for quick reference.
CAUTIONACOUSTIC OUTPUT HAZARD
Although the ultrasound energy transmitted from  the LOGIQ™ P5/A5/A5Pro probe is within 
FDA limits, avoid unnecessary exposure. Ultrasound energy can produce heat and 
mechanical damage.
Figure 3-1   Environmental Labels 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL 
3-4 Section 3-1 - Overview
Section 3-3
Receiving and Unpacking the Equipment
When a new system arrives, check that any components are not damaged and are not in short supply. 
If shipping damage or shortage occurs, contact the address shown in Chapter 1.
1.) Cut the three PLASTIC BANDs.
Figure 3-2   Cutting the Plastic Bands.
CAUTIONDo not lift the unit by the Keyboard. Equipment damage may result.
CAUTIONThe crate with the LOGIQ™ P5/A5/A5Pro weighs approximately 75 kg. (165 lb.) Be prepared for 
a sudden shift of weight as the unit is removed from its base (pallet)
Plastic Bands 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION 1 LOGIQ™ P5 SERVICE MANUAL
Section 3-1 - Overview 3-5
Section 3-3      Receiving and Unpacking the Equipment (cont’d)
2.) Lift the TOP COVER up and off.
Figure 3-3   Removing the top Cover
Top Cover 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL 
3-6 Section 3-1 - Overview
Section 3-3      Receiving and Unpacking the Equipment (cont’d)
3.) Remove the Top Plate up and off..
Figure 3-4   Removing the Top Plate
Top Plate 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION 1 LOGIQ™ P5 SERVICE MANUAL
Section 3-1 - Overview 3-7
Section 3-3      Receiving and Unpacking the Equipment (cont’d)
4.) Remove the three PLASTIC JOINTs from the OUTER SLEEVE.
5.) Remove the OUTER SLEEVE.
Figure 3-5   Removing Plastic Joints and Sleeves
Plastic Joint Outer Sleeve
Palette Assy 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL 
3-8 Section 3-1 - Overview
Section 3-3      Receiving and Unpacking the Equipment (cont’d)
6.) Remove the MONITOR SUPPORTER and Option Box.
7.) Remove the PLASTIC BAG.
8.) Unlock the front caster and carefu lly put the console off the PALETTE.
Figure 3-6   Moving the LOGIQ™ P5/A5/A5Pro from the crate
Monitor Pad 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION 1 LOGIQ™ P5 SERVICE MANUAL
Section 3-1 - Overview 3-9
3-3-1 Moving into Position
In general, a single adult can move the LOGIQ™ P5/A5/A5Pro along an even surface with no steep 
grades. At least two people should move the machine when la rge humps, grooves, or grades will be 
encountered. (It is better to pull from the rear rather  than push from the front of the unit). Before moving, 
store all loose parts in the unit. Wrap transducers in soft cloth or foam to prevent damage.
Although LOGIQ™ P5/A5/A5Pro is a compact and mob ile machine, two people should move it over 
rough surfaces or up and down grades.
3-3-2 Adjusting System Clock
Set the system clock for the LOGIQ™ P5/A5/A5Pro to the local time. For procedure of adjusting the 
system clock, refer to section 3-6-1-1 on page 16.
Fill out proper customer Information the Product Locator Installation Card. Mail this Installation Card 
“Product Locator” to the address corresponding to your pole.
3-3-3 Product Locator  Installation Card
NOTE: The Product Locator Installation Card shown  may not be same as the provided Product Locator 
card.
CAUTIONDo not lift the unit by the Keyboard.
Do not tilt the unit more than 5 degrees to avoid tipping it over.
To avoid injury by tipping over. Set the monitor to the lowest position before moving.
CAUTIONEquipment Damage Possibility. Lifting the cons ole by holding covers may damage the covers. 
Do not lift the console by holding any covers.
Figure 3-7   Product Locator Installation Card 
						

							GE HEALTHCARE
DIRECTION 5394141, REVISION  1 LOGIQ™ P5 SERVICE MANUAL 
3-10 Section 3-4 - Preparing for Installation
Section 3-4
Preparing for Installation
3-4-1 Verify Customer Order
Compare items received by the customer to that whic h is listed on the delivery order. Report any items 
that are missing, back ordered or damaged.
3-4-2 Physical Inspection
3-4-2-1 System Voltage Settings
Verify that the scanner is set to the correct voltage.
The Voltage settings for the LOGIQ™ P5/A5/A5Pro Scanner is found on a label to the right of the Power 
switch and External I/O, on the rear of the system.
3-4-2-2 Video Formats Check that the video format for VCR playback is set  to the locally used video standard, NTSC or PAL.
3-4-3 EMI Protection
This Unit has been designed to minimize the effects of  Electro Magnetic Interference (EMI). Many of the 
covers, shields, and screws are provided primarily to  protect the system from image artifacts caused by 
this interference. For this reason, it  is imperative that all covers and hardware are installed and secured 
before the unit is put into operation.
WARNINGWARNINGConnecting a LOGIQ™ P5/A5/A5Pro scanner to the wrong voltage level will most likely 
destroy the scanner.