Home > Toshiba > Printer > Toshiba Estudio 230 Manual

Toshiba Estudio 230 Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual Toshiba Estudio 230 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 708
    Add page 651 to Favourites
    image text
    Enable zoom 
    							June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 POWER SUPPLY UNIT
7 - 1
7
7. POWER SUPPLY UNIT 
7.1 Output Channel
The followings are five output channels which are n ot linked with the door switch.
1) +3.3V +3.3VA : CN705 Pins 13, 14, 15 and 16 Output to the SYS board
+3.3VB : CN705 Pins 19 and 20
Output to the SYS board
+3.3VB : CN706 Pin 30 Output to the LGC board
+3.3VB : CN708 Pins 9 and 10 Output to the SLG board
2) +5.1V +5.1VA : CN705 Pins 24 and 26
Output to the SYS board
+5.1VB : CN705 Pin 25
Output to the SYS board
+5.1VB : CN706 Pin 26
Output to the FUS board
+5.1VB : CN706 Pins 27 and 28 Output to the LGC board, PFP/ LCF (via LGC board), 
Bridge unit / Job separator / Offset tray (via LGC  board)
+5.1VB : CN707 Pin 4 Output to the finisher
+5.1VB : CN708 Pins 3 and 4 Output to the SLG board
+5.1VB : CN708 Pins 5 and 6
Output to the RADF
3) +12V +12VA : CN705 Pin 7 Output to the SYS board
+12VB : CN705 Pin 5 Output to the SYS board
+12VB : CN706 Pin 22 Output to the LGC board
+12VB : CN708 Pin 13 Output to the SLG board
4) -12V -12VA : CN705 Pin 9 Output to the SYS board
-12VB : CN705 Pin 3
Output to the SYS board
5) +24V +24VB : Not used
    Add page 652 to Favourites
    image text
    Enable zoom 
    							e-STUDIO200L/202L/230/232/280/282 POWER SUPPLY UNITJune 2004 © TOSHIBA TEC
7 - 2
The followings are two output channels which are li nked with the door switch.
1) +5.1V +5.1VD : CN706 Pin 2 Output to the LGC board
2) +24V +24VD1 : CN706 Pins 11, 12, 13 and 14 Output to the LGC board, PFP/LCF (via LGC board)
+24VD1 : CN707 Pins 15 and 16 Output to the main motor
+24VD2 : CN706 Pins 5 and 6 Output to the LGC board, High-voltage transformer ( via LGC board),
Bridge unit / Job separator / Offset tray (via LGC  board)
+24VD2 : CN707 Pins 11 and 12 Output to the ADU board
+24VD3 : CN708 Pins 23 and 24 Output to the RADF
+24VD4 : CN708 Pins 19 and 20
Output to the SLG board
+24VD5 : CN707 Pin 8 Output to the finisher
 
Not linked with the door switch 
Linked with the door switch
Connector Destination Voltage
CN705 For the SYS board +3.3VA, +3.3VB, +5.1VA, +5.1V B, 
+12VA, +12VB, -12VA, -12VB
CN706 For the LGC board, FUS board, PFP/LCF (via LGC  
board), Bridge unit / Job separator / Offset tray ( via 
LGC board) +3.3VB, +5.1VB, +12VB
CN707 For the finisher +5.1VB
CN708 For the SLG board, RADF +3.3VB, +5.1VB, +12VB
Connector Destination Voltage
CN706 For the LGC board, High-voltage transformer (v ia 
LGC board), PFP/LCF (via LGC board), Bridge unit /  
Job separator / Offset tray (via LGC board) +5.1VD, +24VD1, +24VD2
CN707 For the ADU board, finisher +24VD1, +24VD2, +24 VD5
CN708 For the SLG board, RADF +24VD3, +24VD4
    Add page 653 to Favourites
    image text
    Enable zoom 
    							June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 POWER SUPPLY UNIT
7 - 3
7
7.2 Fuse
When the power supply secondary fuse is blown out,  confirm that there is no abnormality with each part 
using the following table.
Voltage Board/Unit Part Fuse type
+24VD1 LGC Main motor F4:8A (Semi time-lag)
Toner motor 
Polygonal motor
Tray-up motor
Internal cooling fan 1
Internal cooling fan 2
Auto-toner sensor
Upper drawer feed clutch
Lower drawer feed clutch
Registration roller clutch
Upper transport clutch
Middle transport clutch
Lower transport clutch
Discharge LED
Main switch
PFP/LCF
+24VD2 LGC Exit motor F5:5A (Semi time-lag)
ADU motor
Exhaust fan
Bypass feed clutch
ADU clutch
Bypass pickup solenoid
High-voltage transformer
Key copy counter / Copy key card
Bridge unit / Job separator / Offset tray
+24VD3 RADF F6:4A (Semi time-lag)
+24VD4 SLG Scan motor F7:4A (Semi time-lag)
Exposure lamp (Lamp inverter)
+24VD5 Finisher F8:5A (Semi time-lag)
    Add page 654 to Favourites
    image text
    Enable zoom 
    							e-STUDIO200L/202L/230/232/280/282 POWER SUPPLY UNITJune 2004 © TOSHIBA TEC
7 - 4
7.3 Configuration of Power Supply Unit
 Fig.7-1
PWR-DN 
PWR-EN
+3.3VA 
+3.3VB
+3.3VB
+3.3VB
+5.1VA 
+5.1VB 
+5.1VBCN705 
CN705
CN706
CN708
CN705
CN705 
CN706
+5.1VB CN707 SYS board
SYS board
SYS board, LGC board
SYS board
LGC board 
SLG board
SYS board
SYS board 
SLG board, RADF
+5.1VB CN708Finisher
+12VA CN705 SYS board 
SYS board 
SYS board 
LGC board 
SLG board 
SYS board
-12VA
CN705
+12VB CN705
+12VB CN706
+12VB CN708
-12VB CN705
+24VB Not used
LGC board 
LGC board 
LGC board
ADU board
LGC board, High-voltage transformer 
(
via LGC board ), 
Bridge unit / Job separator /Offset tray  (
via LGC board )
+5.1VD
CN706
LGC board, PFP/LCF  (
via LGC board )
+24VD1 
+24VD2 CN706 
CN706
Main motor
+24VD1
CN707
+24VD2 CN707SYS board, FUS board, PFP/LCF 
(
via LGC board )
,
Bridge unit / Job separator / Offset tray  (
via LGC board )
CN705
CN705,CN706
Regulator
Regulator
F4
RADF
+24VD3
CN708
F6
SLG board
+24VD4
CN708
F7
F2
F1
Finisher
+24VD5
CN707
HTR1ON CN706
HTR2ON CN706
F8
F5
Side heater lamp
control circuit (TRC2 )
Center heater lamp
control circuit(TRC1 )
Main
switch Cover opening/closing 
interlock switch
Fuser center
thermostat
Live
Neutral
Switching regulator
Fuser front
thermostat
CN703
CN704
CN702
CN701
Noise filter
Noise filter
Center heater lamp Side heater lamp FUS board
Damp
heaters
RY
NAD/MJD models: Option 
Other models: Standard
05/11
    Add page 655 to Favourites
    image text
    Enable zoom 
    							June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE
8 - 1
8
8. REMOTE SERVICE
There are following functions as Remote Service. 
1) Auto Supply Order Automatically orders the toner by FAX or E-mail.
2) Service Notification Notifies the status of the equipment to the service  technician by E-mail or FAX.
8.1 Auto Supply Order 
8.1.1 Outline
Automatically orders the toner. 
1) Placing an Order
There are two ways to place an order. 
- FAXInstallation of the FAX board is required. 
If the FAX board has not been installed, it is rega rded as OFF setting.
- E-mail (E-mail body + TIFF image)
2) Order Intervals When the toner empty occurs, the number of occurrenc es is counted. And when it reaches the spec-
ified number for CONDITION, the order is placed aut omatically.
3) If Order Failure Occurs If some problems occur and the order cannot be place d after registering an order as a job, refer to 
the standard countermeasure for the FAX/E-mail tran smission failure.
05/05
    Add page 656 to Favourites
    image text
    Enable zoom 
    							e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICEJune 2004 © TOSHIBA TEC
8 - 2
8.1.2 Setting Item
To enable Auto Supply Order, the following settings 
are required.
Note: Note: 
When selecting E-mail to place an order, it is requ ired that sending and receiving E-mails are 
available. Confirm the details to the administrator .
1) Self-diagnosis (08) Setting As the default setting, the Auto Supply Order setti ng screen is not displayed on the touch panel.
To display it, switching the Valid/Invalid setting  (08-765) is required.
0: Valid (FAX/Internet FAX) 
1: Valid (FAX/Internet FAX/HTTP)*
2: Invalid (Default)
When changing the setting value from “2” (default)  to “0”, the Auto Supply Order setting screen is 
displayed. (* HTTP has not been supported yet.)
    Add page 657 to Favourites
    image text
    Enable zoom 
    							June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE
8 - 3
8
2) Touch Panel Setting Each item is set from the Auto Supply Order screen  on the touch panel.
Entering the password and customer information is r equired because the setting is made from the 
ADMIN screen. Setting it with the administrator is  a must.
- Basic setting [ADMIN] > [SERVICE] > [SUPPLY ORDER SETUP] > [ORDER  INFORMATION]
*1 HTTP has not been supported yet. 
*2 Even when “FAX” is selected, the order is not pl aced without entering the FAX number.
*3 Even when “MAIL” is selected, the order is not p laced without entering the E-mail address.
AUTO SUPPLY ORDER Ordered by: [FAX], [MAIL], [HTTP]  (*1)
FAX NUMBER FAX number of supplier (*2) 
E-MAIL E-mail address of supplier (*3)
CUSTOMER Customer information NAME
TEL NUMBER
E-MAIL
ADDRESS
SUPPLIER Supplier information NAME 
ADDRESS
SERVICE TECHNICIAN Service technician information
NUMBER 
NAME
TEL NUMBER
E-MAIL
    Add page 658 to Favourites
    image text
    Enable zoom 
    							e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICEJune 2004 © TOSHIBA TEC
8 - 4
- Detailed setting for the order [ADMIN] > [SERVICE] > [SUPPLY ORDER SETUP] > [TONER  ORDERING]
*1 The order is placed when the number of replaceme nt reaches the number specified for the 
CONDITION.
- FAX number of this equipment (common information) [ADMIN] > [FAX] > [TERMINAL ID]
- E-mail information of this equipment (common inform ation)
[ADMIN] > [E-MAIL] 
*1 When sending an E-mail, validity of the address  is checked. If the address is invalid, it is not 
sent.
3) Output of setting list of the Auto Supply Order Keying in the following buttons and keys prints the  setting list.
[USER FUNCTIONS] [USER] [LISTS] [*] [#] [*] [*] [3]  [8] [START]
***** TONER ORDER Order information (TONER) 
PART NUMBER Part number to be ordered
CONDITION The number of conditions (*1)
QUANTITY The quantity to be ordered
AUTO ORDER ON/OFF setting of order for each part 
ID NAME ID name of this equipment 
FAX NUMBER FAX number of this equipment 
FROM ADDRESS E-mail address of this equipment (*1) 
FROM NAME E-mail username of this equipment
    Add page 659 to Favourites
    image text
    Enable zoom 
    							June 2004 © TOSHIBA TECe-STUDIO200L/202L/230/232/280/282 REMOTE SERVICE
8 - 5
8
8.1.3 Setting procedure
(1) Start up the self-diagnosis setting mode 08-765,  and then change the setting value to “0”.
(2) Turn the power OFF, and then ON. 
(3) Press the [USER FUNCTIONS] button to enter the user  function screen.
(4) Press the [ADMIN] button.  When the Administrator Password has been set, ADMI NISTRATOR PASSWORD screen is 
displayed.
 Fig.8-1
(5) Press the [PASSWORD] button and the screen is sw itched to a full keyboard. Then key in the 
Administrator Password and press the [ENTER] button .
* Confirm the password to the administrator.
 Fig.8-2
(6) Press the [SERVICE] button in the ADMIN screen.
05/05
    Add page 660 to Favourites
    image text
    Enable zoom 
    							e-STUDIO200L/202L/230/232/280/282 REMOTE SERVICEJune 2004 © TOSHIBA TEC
8 - 6
(7) The SERVICE screen is displayed.
 Fig.8-3
(8) Press the [SUPPLY ORDER SETUP] button.
 Fig.8-4
(9) Press the [ORDER INFORMATION] button. 
(10) The ORDER INFORMATION screen is displayed.
 Fig.8-5
    All Toshiba manuals Comments (0)

    Related Manuals for Toshiba Estudio 230 Manual