Toshiba Estudio 230 Manual
Have a look at the manual Toshiba Estudio 230 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 175 2 412 Fuser Fuser roller temperature during printing (Center thermistor/Thick paper 3) ALL 9 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 413 Fuser Fuser roller temperature during printing (Center thermistor/Thick paper 1) ALL 8 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 414 Devel- operToner density life correc- tion switching ALL 0 M 0: Unchanged (Default) 1: Approx. 0.3 wt% higher 2: Approx. 0.6 wt% higher 3: Approx. 0.9 wt% higher 4: Approx. 0.2 wt% lower 5: Approx. 0.4 wt% lower 6: Approx. 0.6 wt% lower 7: Approx. 0.9 wt% lower 1 417 Fuser Pre-running time for first printing (Thick paper 3) ALL 10 M 0: Invalid 1: 1 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. 1 Setting mode (08) Code Classifi- cation ItemsFunc- tion Default RAM Contents Proce- dure 05/11
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 176 424-0 Fuser Temperature drop switching time setting in ready status (Center ther- mistor)The first drop ALL 15 M This code is valid only when “20” is set to 08- 886. Setting value x 1 min.: from 2 to 60 min. later 4 424-1 The sec- ond dropALL 15 M 4 424-2 The third dropALL 15 M 4 424-3 The fourth dropALL 15 M 4 425-0 Fuser Temperature drop switching time setting in ready status (Side ther- mistor)The first drop ALL 15 M 4 425-1 The sec- ond dropALL 15 M 4 425-2 The third dropALL 15 M 4 425-3 The fourth dropALL 15 M 4 433-0 Fuser Temperature control lower limit (Plain paper/ at ordinary temperature)Center thermistor ALL 7 M 0: 130°C 1: 135°C 2: 140°C 3: 145°C 4: 150°C 5: 155°C 6: 160°C 7: 165°C 8: 170°C 9: 175°C 10: 180°C 11: 185°C 12: 120°C 4 433-1 Side ther- mistorALL 5 M 4 437 Fuser Fuser roller temperature during printing (Center thermistor /Thick paper 2) ALL 8 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 438 Fuser Fuser roller temperature during printing (Center thermistor/OHP film) ALL 8 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 439 Fuser Pre-running time for first printing (Thick paper 2) ALL 10 M 0: Invalid 1: 1 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. 1 Setting mode (08) Code Classifi- cation Items Func- tion Default RAM Contents Proce- dure 05/11
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 177 2 440 Fuser Pre-running time for first printing (Plain paper) ALL 0 M 0: Invalid 1: 1 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. 1 441 Fuser Pre-running time for first printing (Thick paper 1) ALL 0 M 0: Invalid 1: 1 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. 1 448 Fuser Fuser roller temperature in Energy Saving Mode (Side thermistor) ALL 0 M 0: OFF 1: 40°C 2: 50°C 3: 60°C 4: 70°C 5: 80°C 6: 90°C 7: 100°C 8: 110°C 9: 120°C 10: 130°C 11: 140°C 12: 150°C 13: 160°C 1 449 Paper feeding Incorrect paper size jam detection switching ALL 0 M 0: Enabled 1: Disabled 1 450 Fuser Fuser roller temperature during printing (Side thermistor/Plain paper) ALL 8 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 451 Fuser Fuser roller temperature during printing (Side thermistor/Thick paper 1) ALL 8 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 Setting mode (08) Code Classifi- cation ItemsFunc- tion Default RAM Contents Proce- dure 05/11
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 178 452 Fuser Fuser roller temperature during printing (Side thermistor/Thick paper 2) ALL 8 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 453 Fuser Fuser roller temperature during printing (Side thermistor/OHP film) ALL 8 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 455 Image process- ing Toner supply amount cor- rection/Toner motor control ALL 0 M Corrects the supply amount of the fresh toner (driving period of the toner motor) into the developer unit. 0: x1.0 1: x0.75 2: x0.5 3: x0.3 4: x2.0 5: x1.5 1 Setting mode (08) Code Classifi- cation ItemsFunc- tion Default RAM Contents Proce- dure 05/11
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 179 2 462 RADF Setting for switchback operation in mixed-size copying using RADF ALL 0 M This setting is whether the original length is detected or not by transporting without scanning in reverse when A4-R/FOLIO paper or LT-R/LG paper is detected in a mixed- size copying. 0: Disabled - AMS:A series - Judges as A4-R without trans- porting in reverse with no scanning. LT series - Judges whether it is LT-R or LG by its length without transporting in reverse with no scanning. APS: A series - Judges whether it is A4-R or FOLIO without transporting in reverse with no scanning. LT series - Judges whether it is LT-R or LG without trans- porting in reverse with no scanning. 1: Enable 1 AMS: A series - Judges whether it is A4-R or FOLIO by transport- ing without scanning in reverse to detect its length. LT series - Judges whether it is LT-R or LG by transporting without scanning in reverse to detect its length. APS: The same as that of APS in 0: Disabled. 2: Enable 2 AMS/APS: The same as that of AMS in 1: Enable 1. 1 463-0 Paper feeding Feeding retry number set- ting (upper drawer) Plain paper ALL 5 M Sets the number of times of the feeding retry from the upper drawer. 4 463-1 Others ALL 5 M 4 Setting mode (08) Code Classifi- cation ItemsFunc- tion Default RAM Contents Proce- dure 05/11
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 180 464-0 Paper feeding Feeding retry number set- ting (lower drawer) Plain paper ALL 5 M Sets the number of times of the feeding retry from the lower drawer. 4 464-1 Others ALL 5 M 4 465-0 Paper feeding Feeding retry number set- ting (PFP upper drawer) Plain paper ALL 5 M Sets the number of times of the feeding retry from the PFP upper drawer. 4 465-1 Others ALL 5 M 4 466-0 Paper feeding Feeding retry number set- ting (PFP lower drawer) Plain paper ALL 5 M Sets the number of times of the feeding retry from the PFP lower drawer. 4 466-1 Others ALL 5 M 4 467-0 Paper feeding Feeding retry number set- ting (bypass feed) Plain paper ALL 5 M Sets the number of times of the feeding retry from the bypass tray. 4 467-1 Others ALL 5 M 4 468-0 Paper feeding Feeding retry number set- ting (LCF) Plain paper ALL 5 M Sets the number of times of the feeding retry from the LCF. 4 468-1 Others ALL 5 M 4 471 Paper feeding Paper size (Postcard) feeding/widthwise direction ALL 148/100 M * Postcard is sup- ported only for JPN model. 10 477 General Machine identification information ALL Refer to content M Lower drawer model: 0 Upper drawer model: 1 2 478 Laser Judged number of polygo- nal motor rotation error (Normal rotation) ALL 0 M Displays the error [CA10] when the set number of rotation error has been detected. 0: 2 times 1: 12 times 1 479 Laser Judged number of polygo- nal motor rotation error (At acceleration/decelera- tion) ALL 0 M 0: Waiting time for polygonal motor rotation overshoot- ing 0.6 sec. 1: Waiting time for polygonal motor rotation overshoot- ing 2.2 sec. 1 480 Paper feeding Default setting of paper source PPC 0 SYS 0: A4/LT 1: LCF 2: Upper drawer 3: Lower drawer 4: PFP upper drawer 5: PFP lower drawer 1 Setting mode (08) Code Classifi- cation ItemsFunc- tion Default RAM Contents Proce- dure 05/11
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 181 2 481 Paper feeding Automatic change of paper source PPC 1 SYS Sets whether or not changing the drawer automatically to the other drawer with the paper of the same size when paper in the selected drawer has run out. 0: OFF 1: ON (Changes to the drawer with the same paper direc- tion and size: ex. A4 to A4) 2: ON (Changes to the drawer with the same paper size. Paper with the dif- ferent direction is acceptable as long as the size is the same: ex., A4 to A4- R, LT-R to LT. “1” is applied when the staple/hole-punch is specified.) 1 482 Paper feeding Feeding retry setting ALL 0 M 0: ON 1: OFF 1 483 Laser Pre-running rotation of polygonal motor ALL 0 SYS Sets whether or not switching the polygonal motor from the standby rotation to the normal rotation when the origi- nal is set on the RADF or the platen cover is opened. 0: Valid (when using RADF and the origi- nal is set manually) 1: Invalid 2: Valid (when using RADF only) 1 484 Laser Polygonal motor rotational status switching at the Auto Clear Mode ALL 0 SYS Sets whether or not switching the polygonal motor from the normal rotation to the standby rotation at the Auto Clear Mode. 0: Valid 1: Invalid 1 485 Laser Rotational status of polygo- nal motor on standby ALL 1 SYS Sets the rotational sta- tus of polygonal motor on standby. 0: Rotated (The rota-tional speed is set at 08-490.) 1: Stopped 1 Setting mode (08) Code Classifi- cation ItemsFunc- tion Default RAM Contents Proce- dure 05/11
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 182 486 Laser Timing of auto-clearing of polygonal motor pre-run- ning rotation ALL 0 SYS Switches the polygonal motor to the standby rotation when a certain period of time has passed from the pre- running. At this code, the period to switch the status to the standby rotation is set. 0: 15 sec.1: 30 sec. 2: 45 sec. * This setting is effec-tive when “0” or “2” is set at 08-483. 1 488 Laser Setting of polygonal motor type ALL 0 M Set the type of polygo- nal motor. 0: 2-clock type 1: 3-clock type 2: 4-clock type 3: 4-clock type 1 489 Laser Polygonal motor rotation number on standby ALL 5 M 0: 38,090.55 rpm 1: 35,000 rpm 2: 30,000 rpm 3: 25,000 rpm 4: 20,000 rpm 5: 10,000 rpm 1 490 Laser Polygonal motor rotation in the energy saving mode ALL 0 M 0: Stopped 1: 10,000 rpm 1 491 Transfer Transfer charger bias cor- rection (H) at duplexing ALL 149 M Corrects the transfer charger bias output value of the leading edge area of paper at duplexing. 1 492 Transfer Transfer charger bias cor- rection (C) at duplexing ALL 139 M Corrects the transfer charger bias output value of the center area of paper at duplexing. 1 493 Transfer Transfer charger bias cor- rection (L) at duplexing ALL 128 M Corrects the transfer charger bias output value of the trailing edge area of paper at duplexing. 1 502 Image Error diffusion and dither setting at photo mode PPC 1 SYS Sets the image repro- duction method at photo mode. 0: Error diffusion 1: Dither 1 503 User interface Default setting of density adjustment PPC 0 SYS 0: Automatic 1: Manual (Center) 1 Setting mode (08) Code Classifi- cation ItemsFunc- tion Default RAM Contents Proce- dure 05/11
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 183 2 508 Image Custom Mode setting PPC 0 SYS 0: Not used 1: Custom Mode 1 when Text/Photo is set as a base 2: Custom Mode 2 when Text is set as a base 3: Custom Mode 3 when Photo is set as a base 1 509 Image Error diffusion and dither setting at a photo mode (Custom Mode) PPC 1 SYS Switches the image processing method when Custom Mode 3 is set. 0: Error diffusion 1: Dither 1 515 Fuser Temperature setting of warming-up (Center thermistor) ALL 9 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 516 Fuser Temperature setting of warming-up (Side thermistor) ALL 9 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 518 Fuser Fuser roller temperature during printing (Side thermistor/Thick paper 3) ALL 9 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 520 Fuser Fuser roller temperature during printing (Center thermistor/Enve- lope) ALL 9 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 Setting mode (08) Code Classifi- cation ItemsFunc- tion Default RAM Contents Proce- dure 05/11
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC 2 - 184 521 Fuser Fuser roller temperature during printing (Side thermistor/Envelope) ALL 9 M 0: 140°C 1: 145°C 2: 150°C 3: 155°C 4: 160°C 5: 165°C 6: 170°C 7: 175°C 8: 180°C 9: 185°C 10: 190°C 11: 195°C 12: 200°C 13: 205°C 14: 210°C 1 523 Fuser Pre-running time for first printing (Envelope) ALL 10 M 0: Invalid 1: 1 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. 1 525-0 Fuser Temperature drop switching time setting during printing (Center ther- mistor)The first drop ALL 20 M This code is valid only when “20” is set to 08- 535. Setting value x 5 sec.: from 0 to 1,000 sec. later 4 525-1 The sec- ond dropALL 38 M 4 525-2 The third dropALL 75 M 4 525-3 The fourth dropALL 75 M 4 526 Fuser Pre-running time for first printing (OHP film) ALL 0 M 0: Invalid 1: 0 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 9 sec. 10: 10 sec. 11: 12 sec. 12: 14 sec. 13: 16 sec. 14: 18 sec. 15: 20 sec. 1 527-0 Fuser Temperature drop switching time setting during printing (Side ther- mistor)The first drop ALL 20 M This code is valid only when “20” is set to 08- 535. Setting value x 5 sec.: from 0 to 1,000 sec. later 4 527-1 The sec- ond dropALL 30 M 4 527-2 The third dropALL 48 M 4 527-3 The fourth dropALL 75 M 4 Setting mode (08) Code Classifi- cation ItemsFunc- tion Default RAM Contents Proce- dure 05/11