Toshiba Estudio 230 Manual

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 5
2
E910 Finisher jam (Bridge unit) Jam at the bridge unit transport sensor-1: The  
paper does not reach the bridge unit transport sen- 
sor-1 after it has passed the exit sensor. P. 5-35
E920 Stop jam at the bridge unit transport sensor-1:  The 
trailing edge of the paper does not pass the bridge  
unit transport sensor-1 after its leading edge has 
reached the sensor. P. 5-35
E930 Jam at the bridge unit transport sensor-2: The  trail-
ing edge of the paper does not reach the bridge uni t 
transport sensor-2 after its leading edge has 
reached the bridge unit transport sensor-1. P. 5-35
E940 Stop jam at the bridge unit transport sensor-2:  The 
trailing edge of the paper does not reach the bridg e 
unit transport sensor-2 after its leading edge has 
reached the bridge unit transport sensor-2. P. 5-35
E950 Job separator jam Jam not reaching the job separa tor transport sen-
sor: The paper has passed through the exit sensor  
does not reach the job separator transport sensor. P. 5-11
E951 Stop jam at the job separator transport sensor:  The 
trailing edge of the paper does not pass the job se p-
arator transport sensor. P. 5-11
E960 Offset tray jam Jam not reaching the offset tray t ransport sensor: 
The paper has passed through the exit sensor does  
not reach the offset tray transport sensor. P. 5-11
E961 Stop jam at the offset tray transport sensor: T he 
trailing edge of the paper does not pass the offset  
tray transport sensor. P. 5-11
E9F0 Finisher jam (Puncher unit) Punching jam: Punching is not performed properly. 
[MJ-1025 (When MJ-6005 is installed)] P. 5-36
EA10 Finisher jam (Finisher unit) Paper transport delay jam: The paper which has  
passed the bridge unit does not reach the inlet sen-
sor. [MJ-1022/1025] P. 5-37
EA20 Paper transport stop jam: The paper does not pa ss 
through the inlet sensor. [MJ-1022/1025] P. 5-38
EA30 Power-ON jam: Paper exists at the inlet sensor  when power is turned ON. [MJ-1022/1025] P. 5-39
EA40 Door open jam: The finisher has been released  from the equipment during printing. [MJ-1022/1025] P. 5-40
EA50 Stapling jam: Stapling is not performed properly . 
[MJ-1022/1025] P. 5-41
EA60 Early arrival jam: The inlet sensor detects the  paper 
earlier than a specified timing. [MJ-1022] P. 5-42
EA70 Stack delivery jam: It cannot deliver the stack  of 
paper on the intermediary process tray to the stack  
tray. [MJ-1022/1025] P. 5-43
EAB0 Finisher jam (Saddle Stitcher sec- 
tion) Saddle paper transport stop jam: The paper which  
passed through the inlet sensor does not reach or  
pass through the folding position sensor. [MJ-1025]
P. 5-45
EAC0 Saddle transport delay jam: The paper which has  reached the inlet sensor does not pass through this  
sensor. [MJ-1025] P. 5-45
EAD0 Other paper jam Print end command time-out jam:  The printing has 
not finished normally because of the communica- 
tion error between the SYS board and LGC board  
at the end of printing. P. 5-46
Error code Classification Contents Troubleshooting 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 6
EAE0 Finisher jam Receiving time time-out jam: The pr
inting has been 
interrupted because of the communication error  
between the equipment and finisher when the 
paper is transported from the equipment to the fin- 
isher. P. 5-46
EAF0 Finisher jam (Finisher unit) Stack return jam: It cannot load the paper which  
passed through the delivery roller on the intermedi-
ary process tray. [MJ-1022] P. 5-44
EB30 Finisher jam Ready time time-out jam: The equipm ent judges 
that the paper transport to the finisher is disable d 
because of the communication error between the 
equipment and finisher at the start of printing. P. 5-46
EB50 Paper transport jam Paper remaining on the trans port path: The multiple 
feeding of preceding paper caused the misfeeding 
of upcoming paper. P. 5-12
EB60 Paper remaining on the transport path: The mult iple 
feeding of preceding paper caused the misfeeding  
of upcoming paper (redetection after no jam is  
detected at [EB50]). P. 5-14
Error code Classification Contents Troubleshooting 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 7
2
2.1.2 Service call
Error code Classification Contents Troubleshooting C010 Drive system  related service call Main motor abnormality: The main motor is not rotat
ing 
normally. P. 5-47
C040 Paper feeding sys- tem related ser- 
vice call PFP motor abnormality: The PFP motor is not rotating  
normally.
P. 5-48
C130 Upper drawer tray abnormality: The upper drawer  tray 
motor is not rotating or the upper drawer tray is n ot mov-
ing normally. P. 5-49
C140 Lower drawer tray abnormality: The lower drawer  tray 
motor is not rotating or the lower drawer tray is n ot mov-
ing normally. P. 5-49
C150 PFP upper drawer tray abnormality: The PFP uppe r 
drawer tray motor is not rotating or the PFP upper  drawer 
tray is not moving normally. P. 5-50
C160 PFP lower drawer tray abnormality: The PFP lowe r 
drawer tray motor is not rotating or the PFP lower d rawer 
tray is not moving normally. P. 5-50
C180 LCF tray-up motor abnormality: The LCF tray-up  motor is 
not rotating or the LCF tray is not moving normally .P. 5-51
C1A0 LCF end fence motor abnormality: The LCF end fen ce 
motor is not rotating or the LCF end fence is not mo ving 
normally. P. 5-52
C1B0 LCF transport motor abnormality: The LCF transp ort 
motor is not rotating normally. P. 5-53
C260 Scanning system  related service call Peak detection error: Lighting of the exposure lamp
 
(white reference) is not detected when power is tur ned 
ON. P. 5-54
C270 Carriage home position sensor not turning OFF w ithin a 
specified period of time: The carriage does not shi ft from 
its home position in a specified period of time. P. 5-55
C280 Carriage home position sensor not turning ON wi thin a 
specified period of time: The carriage does not rea ch to 
its home position in a specified period of time. P. 5-55
C410 Fuser unit related  service call Thermistor or heater abnormality at power-ON: Abnor
-
mality of service call the thermistor is detected w hen 
power is turned ON or the temperature of the fuser  roller 
does not rise in a specified period of time after p ower is 
turned ON. P. 5-56
C440 Heater abnormality after abnormality judgment:  The tem-
perature of the fuser roller has exceeded the range  of 
control (in this case, the main switch turns OFF au tomati-
cally) or does not even reach the range. P. 5-57
C450 Thermistor abnormality during printing: Abnorma lity of the 
thermistor is detected during printing. P. 5-57
C550
(C780) Optional communi- 
cation related ser- 
vice call RADF I/F error: Communication error has occurred  
between the RADF and the scanner.
P. 5-58
C570 Communication error between Engine-CPU and IPC  board P. 5-58
C580 Communication error between IPC board and finis her P. 5-58
C730 RADF related ser- vice call EEPROM initialization error: EEPROM is not initiali
zed 
normally when performing the code 05-356. P. 5-59
C810 Fan motor abnormality: The fan motor is not rot ating nor-
mally. P. 5-59
C820 Read sensor adjustment error: The read sensor ca nnot 
be adjusted normally when performing the code 05-356 .P. 5-59
C830 Original length sensor adjustment error: The or iginal 
length sensor cannot be adjusted normally when per- 
forming the code 05-356. P. 5-59
05/05 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 8
C940 Circuit related ser-
vice call Engine-CPU abnormality
P. 5-76
C970 Process related  service call High-voltage transformer abnormality: Leakage of th
e 
main charger is detected. P. 5-76
CA10 Laser optical unit  related service call Polygonal motor abnormality: The polygonal motor is
 not 
rotating normally. P. 5-60
CA20 H-Sync detection error: H-Sync detection PC boa rd can-
not detect laser beams. P. 5-60
CB10 Finisher related  service call Transport motor abnormality: The transport motor or
 
stack transport roller is not rotating normally. [M J-1025]P. 5-61
CB20 Delivery motor abnormality: Delivery motor or d elivery 
roller is not rotating normally. [MJ-1022/1025] P. 5-62
CB30 Tray lift motor abnormality: The tray lift moto r is not rotat-
ing normally or the delivery tray is not moving norm ally. 
[MJ-1025] P. 5-63
CB50 Staple motor (staple/fold) abnormality: The sta ple motor 
is not rotating normally or the stapler is not movin g nor-
mally. [MJ-1025] P. 5-64
CB60 Stapler unit shift motor abnormality: The stapl er unit shift 
motor is not rotating normally or the Stapler Unit  is not 
moving normally. [MJ-1025] P. 5-66
CB80 Backup RAM data abnormality: 1) Abnormality of checksum value on finisher control ler 
board is detected when the power is turned on. 
[MJ-1025]
2) Abnormality of checksum value on punch controller  board is detected when the power is turned on. 
[MJ-1025 (when MJ-6005 is installed)] P. 5-67
CC30 Stack processing motor abnormality: The stack p rocess-
ing motor is not rotating normally or the stack del ivery belt 
is not moving normally. [MJ-1022] 
Paddle motor abnormality: The paddle motor is not r otat-
ing normally or the swing guide is not moving norma lly. 
[MJ-1025] P. 5-67
CC50 Horizontal registration motor abnormality: The  horizontal 
registration motor is not rotating normally or the  puncher 
is not moving normally. 
[MJ-1025 (when MJ-6005 is installed)] P. 5-69
CC60 Punch motor abnormality: The punch motor is not  rotating 
normally or the puncher is not moving normally.
[MJ-1025 (when MJ-6005 is installed)] P. 5-69
CC80 Front jogging motor abnormality: Front jogging  motor is 
not rotating normally or the front alignment plate  is not 
moving normally. [MJ-1022]
Alignment motor (front) abnormality: The alignment  motor 
(front) is not rotating normally or the front align ment plate 
is not moving normally. [MJ-1025] P. 5-70
CC90 Upper stack tray lift motor abnormality: The up per stack 
tray lift motor is not rotating or the upper stack tray is not 
moving normally. [MJ-1022] P. 5-71
CCA0 Lower stack tray lift motor abnormality: The lo wer stack 
tray lift motor is not rotating or the lower stack tray is not 
moving normally. [MJ-1022] P. 5-72
CCB0 Rear jogging motor abnormality: Rear jogging mo tor is 
not rotating normally or the rear alignment plate i s not 
moving normally. [MJ-1022]
Alignment motor (rear) abnormality: The alignment m otor 
(rear) is not rotating normally or the rear alignme nt plate 
is not moving normally. [MJ-1025] P. 5-73
Error code Classification Contents Troubleshooting 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 9
2
CDC0 Finisher related  service call Punch power failure abnormality: 24 V is not applie
d to 
the punch controller board. 
[MJ-1025 (when MJ-6005 is installed)] P. 5-74
CDD0 Folding position sensor abnormality: Automatic  adjust-
ment of the folding position sensor can not be perfo rmed 
properly. [MJ-1025] P. 5-74
CDE0 Paddle motor abnormality: The paddle motor does  not 
rotate properly. [MJ-1025] P. 5-75
CDF0 Offset tray related  service call Initialization error of the offset tray: The home p
osition of 
the separator cannot be detected when the power is  
turned ON. P. 5-76
CE00 Finisher related  service call Communication error between finisher unit and punch
er 
unit: Communication error between the finisher cont roller 
PC board and punch controller PC board.
[MJ-1025 (when MJ-6005 is installed)] P. 5-75
CF60 Other service call Toner for recycle transport a rea lock P. 5-76
F070 Communication  related service call Communication error between System-CPU and Engine- 
CPU P. 5-58
F090 Other service call SRAM abnormality on the SYS bo ard P. 5-76
F091 NVRAM abnormality on the SYS board P. 5-77 
F092 SRAM and NVRAM abnormality on the SYS board P. 5 -77
F100 HDD format error: HDD cannot be initialized nor mally. P. 5-77
F101 HDD unmounted: Connection of HDD cannot be  detected. P. 5-77
F102 HDD start error: HDD cannot become ‘Ready’ stat e. P. 5-77
F103 HDD transfer time-out: Reading/writing cannot b e per-
formed in the specified period of time. P. 5-77
F104 HDD data error: Abnormality is detected in the  data of 
HDD. P. 5-77
F105 HDD other error P. 5-77
F106 Point and Print partition damage P. 5-78
F107 /SHR partition damage P. 5-78
F108 /SHA partition damage P. 5-78
F110 Communication  related service call Communication error between System-CPU and Scan- 
ner-CPU P. 5-58
F111 Scanner response abnormality P. 5-58
F120 Other service call Database abnormality: Database  is not operating nor-
mally. P. 5-78
F130 Invaid MAC address P. 5-78
F200 Data overwrite kit (GP-1050/1060) is taken off P.  5-78
Error code Classification Contents Troubleshooting 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 10
2.1.3 Error in Internet FAX / Scanning Function
1) Internet FAX related error 
(when GM-1020/3020, 1030/3030, 2020 or 2030 is inst alled (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is i nstalled (e-STUDIO202L/232/282))
Error code Contents Troubleshooting
1C10 System access abnormality P. 5-79
1C11 Insufficient memory P. 5-79
1C12 Message reception error P. 5-79
1C13 Message transmission error P. 5-79
1C14 Invalid parameter P. 5-79
1C15 Exceeding file capacity P. 5-79
1C20 System management module access abnormality P. 5 -79
1C21 Job control module access abnormality P. 5-79
1C22 Job control module access abnormality P. 5-79
1C30 Directory creation failure P. 5-80
1C31 File creation failure P. 5-80
1C32 File deletion failure P. 5-79
1C33 File access failure P. 5-80
1C40 Image conversion abnormality P. 5-80
1C60 HDD full failure during processing P. 5-80
1C61 Address Book reading failure P. 5-80
1C62 Memory acquiring failure P. 5-80
1C63 Terminal IP address unset P. 5-80
1C64 Terminal mail address unset P. 5-80
1C65 SMTP address unset P. 5-80
1C66 Server time time-out error P. 5-80
1C67 NIC time time-out error P. 5-80
1C68 NIC access error P. 5-80
1C69 SMTP server connection error P. 5-81
1C6A HOST NAME error P. 5-81
1C6B Terminal mail address error P. 5-81
1C6C Destination mail address error P. 5-81
1C6D System error P. 5-80
1C70 SMTP client OFF P. 5-81
1C71 SMTP authentication error P. 5-81
1C72 POP before SMTP error P. 5-81
1C80 Internet FAX transmission failure when processi ng E-mail job received P. 5-81
1C81 Onramp Gateway transmission failure P. 5-81
1C82 Internet FAX transmission failure when processi ng FAX job received P. 5-81
1CC0 Job canceling -
1CC1 Power failure P. 5-81
05/11 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 11
2
2) RFC related error  (when GM-1020/3020, 1030/3030, 2020 or 2030 is inst alled (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is i nstalled (e-STUDIO202L/232/282))
Error codeMessage displayed in the 
TopAccess screen Contents Troubleshooting
2500 Syntax error, command unrecog- nized HOST NAME error (RFC: 500) 
Destination mail address error 
(RFC: 500)
Terminal mail address error 
(RFC: 500) P. 5-82
2501 Syntax error in parameters or  arguments HOST NAME error (RFC: 501) 
Destination mail address error
(RFC: 501) 
Terminal mail address error 
(RFC: 501) P. 5-82
2503 Bad sequence of commands Destination mail addres s error
(RFC: 503) P. 5-82
2504 Command parameter not imple- mented HOST NAME error (RFC: 504) P. 5-82
2550 Mailbox unavailable Destination mail address err or
(RFC: 550) P. 5-82
2551 User not local Destination mail address error (RFC: 551) P. 5-82
2552 Insufficient system storage Terminal/Destination  mail address error 
(RFC: 552) P. 5-82
2553 Mailbox name not allowed Destination mail addres s error
(RFC: 553) P. 5-82
05/11 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 12
3) Electronic Filing related error
Error code Message displayed in the 
TopAccess screen Contents Troubleshooting
2B10 There was no applicable job. No applicable job e rror in job control 
module P. 5-83
2B11 Job status failed. JOB status abnormality P. 5-83
2B20 Failed to access file. File library function err or P. 5-83
2B30 Insufficient disk space. Insufficient disk space  in /SHR partition P. 5-83
2B31 Failed to access Electronic Filing. Status of sp ecified Electronic Filing or 
folder is undefined or being created/ 
deleted P. 5-83
2B32 Failed to print Electronic Filing  document. Electronic Filing printing failure: 
Specified document can not be printed  
because of clients access (being edited,  
etc.). P. 5-83
2B50 Failed to process image. Image library error P. 5 -83
2B51 Failed to process print image. List library erro r P. 5-83
2B71 Document(s) expire(s) in a few  days Documents expiring in a few days exist -
2B80 Hard Disk space for Electronic  Filing nearly full. Hard disk space in /SHR partition is 
nearly full (90%). -
2B90 Insufficient Memory. Insufficient memory capacity P. 5-83
2BA0 Invalid Box password specified. Invalid Box pass word P. 5-84
2BB0 Job canceled Job canceling -
2BB1 Power failure occurred Power failure P. 5-84
2BC0 System fatal error. Fatal failure occurred. P. 5- 83
2BC1 Failed to acquire resource. System management mo dule resource 
acquiring failure P. 5-83
2BD0 Power failure occurred during e- Filing restoring. Power failure occurred during restoring  
of Electronic Filing P. 5-84
2BE0 Failed to get machine parameter. Machine paramet er reading failure P. 5-84
2BF0 Maximum number of pages has  been exceeded (list Maximum) Exceeding maximum number of pages P. 5-84
2BF1 Maximum number of documents  has been exceeded (list Maxi-
mum) Exceeding maximum number of docu-
ments
P. 5-84
2BF2 Maximum number of folders has  been exceeded (list Maximum) Exceeding maximum number of folders P. 5-84 
						

							June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 13
2
4) E-mail related error  (when GM-1020/3020, 1030/3030, 2020 or 2030 is inst alled (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is i nstalled (e-STUDIO202L/232/282))
Error codeMessage displayed in the 
TopAccess screen Contents Troubleshooting
2C10 Illegal Job status System access abnormality P. 5 -85
2C11 Not enough memory Insufficient memory P. 5-85
2C12 Illegal Job status Message reception error P. 5-8 5
2C13 Illegal Job status Message transmission error P.  5-85
2C14 Invalid parameter specified Invalid parameter P. 5 -85
2C15 Message size exceeded limit or  maximum size Exceeding file capacity P. 5-85
2C20 Illegal Job status System management module acce ss 
abnormality P. 5-85
2C21 Illegal Job status Job control module access abn ormality P. 5-85
2C22 Illegal Job status Job control module access abn ormality P. 5-85
2C30 Failed to create directory Directory creation fa ilure P. 5-85
2C31 Failed to create file File creation failure P. 5- 85
2C32 Failed to delete file File deletion failure P. 5- 85
2C33 Failed to create file File access failure P. 5-85 
2C40 Failed to convert image file for- mat Image conversion abnormality P. 5-85
2C60 Failed to process your Job. Insuf- ficient disk space. HDD full failure during processing P. 5-86
2C61 Failed to read AddressBook Address Book reading  failure P. 5-86
2C62 Not enough memory Memory acquiring failure P. 5-8 5
2C63 Invalid Domain Address Terminal IP address unset P. 5-86
2C64 Invalid Domain Address Terminal mail address uns et P. 5-86
2C65 Failed to connect to SMTP server SMTP address un set P. 5-86
2C66 Failed to connect to SMTP server Server time tim e-out error P. 5-86
2C67 Failed to send E-Mail message NIC time time-out  error P. 5-86
2C68 Failed to send E-Mail message NIC access error P.  5-86
2C69 Failed to connect to SMTP server SMTP server con nection error P. 5-86
2C6A Failed to send E-Mail message HOST NAME error (No  RFC error) P. 5-86
2C6B Invalid address specified in From:  field Terminal mail address error P. 5-86
2C6C Invalid address specified in To:  field Destination mail address error (No RFC  
error) P. 5-87
2C6D NIC system error System error P. 5-86 2C70 SMTP service is not available SMTP client OFF P. 5 -87
2C71 Failed SMTP Authentication SMTP authentication e rror P. 5-87
2C72 POP Before SMTP Authentica- tion Failed POP before SMTP error P. 5-87
2C80 Failed to process received E-mail  job E-mail transmission failure when pro- 
cessing E-mail job received P. 5-87
2C81 Failed to process received Fax  job Process failure of FAX job received P. 5-87
2CC0 Job canceled Job canceling -
2CC1 Power failure occurred Power failure P. 5-87
05/11 
						

							e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE June 2004 © TOSHIBA TEC
2 - 14
5) File sharing related error (when GM-1020/3020, 1030/3030, 2020 or 2030 is inst alled (e-STUDIO200L/230/280))
(when GM-1070/4070, 1080U/4080U, 2070 or 2080U is i nstalled (e-STUDIO202L/232/282))
Error codeMessage displayed in the 
TopAccess screen Contents Troubleshooting
2D10 Illegal Job status System access abnormality P. 5 -88
2D11 Not enough memory Insufficient memory P. 5-88
2D12 Illegal Job status Message reception error P. 5-8 8
2D13 Illegal Job status Message transmission error P.  5-88
2D14 Invalid parameter specified Invalid parameter P. 5 -88
2D15 There are too many documents in  the folder. Failed in creating new  
document. Exceeding document number P. 5-88
2D20 Illegal Job status System management module acce ss 
abnormality P. 5-88
2D21 Illegal Job status Job control module access abn ormality P. 5-88
2D22 Illegal Job status Job control module access abn ormality P. 5-88
2D30 Failed to create directory Directory creation fa ilure P. 5-88
2D31 Failed to create file File creation failure P. 5- 88
2D32 Failed to delete file File deletion failure P. 5- 88
2D33 Failed to create file File access failure P. 5-88 
2D40 Failed to convert image file for- mat Image conversion abnormality P. 5-89
2D60 Failed to copy file File library access abnormal ity P. 5-88
2D61 Invalid parameter specified Invalid parameter P. 5 -88
2D62 Failed to connect to network des- tination. Check destination path File server connection error P. 5-89
2D63 Specified network path is invalid.  Check destination path Invalid network path P. 5-89
2D64 Logon to file server failed. Check  username and password Login failure P. 5-89
2D65 There are too many documents in  the folder. Failed in creating new  
document. Exceeding documents in folder: Creating  
new document is failed.
P. 5-89
2D66 Failed to process your Job. Insuf- ficient disk space. HDD full failure during processing P. 5-89
2D67 FTP service is not available FTP service not availa ble P. 5-89
2D68 File Sharing service is not avail- able File sharing service not available P. 5-89
2DA0 Expired scan documents deleted  from share folder. Periodical deletion of scanned docu- 
ments completed properly. -
2DA1 Expired Sent Fax documents  deleted from shared folder. Periodical deletion of transmitted FAX 
documents completed properly. -
2DA2 Expired Received Fax documents  deleted from shared folder. Periodical deletion of received FAX doc- 
uments completed properly. -
2DA3 Scanned documents in shared  folder deleted upon users  
request. Manual deletion of scanned documents 
completed properly.
-
2DA4 Sent Fax Documents in shared  folder deleted upon users 
request. Manual deletion of transmitted FAX doc- 
uments completed properly.
-
2DA5 Received Fax Documents in  shared folder deleted upon users 
request. Manual deletion of received FAX docu- 
ments completed properly.
-
2DA6 Failed to delete file. File deletion failure P. 5 -88
05/11