Toshiba Estudio 230 Manual

							1
2
3
4
5
6
7
8
9
10
1. SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES
2. ERROR CODE AND SELF-DIAGNOSTIC  MODE
3. ADJUSTMENT 
4. PREVENTIVE MAINTENANCE (PM)
5. TROUBLESHOOTING 
6. FIRMWARE UPDATING 
7. POWER SUPPLY UNIT
8. REMOTE SERVICE 
9. DATA CLONING with USB STORAGE DEVICE  (e-STUDIO202L/232/282)
10. WIRE HARNESS CONNECTION DIAGRAMS 
						

							1
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES
1 - 1
1. SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES 
1.1 Specifications

Copy process Indirect electrophotographic process (dr y)
 Type Desktop type (console type: when paper feed pede stal (PFP) and large 
capacity feeder (LCF) are installed)
 Original table Fixed type (the left rear corner used  as guide to place originals)
 Accepted originals Sheet, book and 3-dimensional obj ect. The reversing automatic document 
feeder (RADF) only accepts paper which are not past ed or stapled. Carbon 
paper are not acceptable either. 
Maximum size: A3/LD
 Copy speed (Copies/min.)
e-STUDIO200L/202L 
e-STUDIO230/230L/232/232S 
e-STUDIO280/280S/282/282S 
* “–” means “Not acceptable”. 
* The copy speed in the above table are available wh en originals are manually placed for single side, 
multiple copying.
Values in { } are for e-STUDIO200L/202L and values 
in [ ] are for e- STUDIO280/280S/282/282S in 
case that the specification is different among e-ST UDIO200L/202L, e-STUDIO230/230L/232/232S 
and e-STUDIO280/280S/282/282S.
Single - sided original Double - sided original
MR-3016 50 ~ 127 g/m2
 (13 lb. Bond - 34 lb. Bond) 50 ~ 105 g/m 2
 (13 lb. Bond - 28 lb. Bond)
MR-3018 35 ~ 157 g/m2
 (9.3 lb. Bond - 58 lb. Cover) 50 ~ 157 g/m 2
 (13 lb. Bond - 58 lb. Cover)
Paper size Drawer Bypass feed
PFP LCF
Size specified Size not specified
A4, LT, B5, A5-R, ST-R 20 20 16 20 20 A4-R, B5-R, LT-R 19 19 16 19 – B4, LG 18 18 16 18 –A3, LD 16 16 16 16 –
Paper size Drawer Bypass feed
PFP LCF
Size specified Size not specified
A4, LT, B5, A5-R, ST-R 23 23 16 23 23 A4-R, B5-R, LT-R 21.5 21.5 16 21.5 – B4, LG 18 18 16 18 –A3, LD 16 16 16 16 –
Paper size Drawer Bypass feed
PFP LCF
Size specified Size not specified
A4, LT, B5, A5-R, ST-R 28 28 16 28 28 A4-R, B5-R, LT-R 21.5 21.5 16 21.5 – B4, LG 18 18 16 18 –A3, LD 16 16 16 16 –
05/11 
						

							e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA  TEC
1 - 2
* When the RADF is used, the copy speed of {20}23[28 ] sheets per minute is only available under the 
following conditions: 
 Original/Mode: Single side original/A4/LT size. APS /automatic density are not selected.
 Number of sheets: {20}23[28] or more.
 Reproduction ratio: 100%
Copy speed for thick paper (Copies/min.) 
e-STUDIO200/200L/230/232/280/282 series 
Thick 1 (81 g/m
2 to 105 g/m2, 21.3 lb. Bond to 28 lb. Bond)
Thick 2 (106 g/m
2 to 163 g/m2, 28 lb. Bond to 90 lb. Index)
Thick 3 (164 g/m
2 to 209 g/m2, 90 lb. Index to 115.7 lb. Index)
* Only A4/LT size is available for the LCF. 
* The tolerance is within ±2.
Paper size Drawer Bypass feed
PFP LCF
Size specified Size not specified
A4, LT, B5, A5-R, ST-R {20} 23 [27] {20} 23 [27] {15}  16 [16] {20} 23 [27] {20} 23 [27]
A4-R, B5-R, LT-R {19} 21 [21] {19} 21 [21] {15} 16 [16 ] {19} 21 [21] {-} - [-]
B4, LG {18} 18 [18] {18} 18 [18] {15} 16 [16] {18} 18 [ 18] {-} - [-]
A3, LD {15} 16 [16] {15} 16 [16] {15} 16 [16] {15} 16 [ 16] {-} - [-]
Paper size Drawer Bypass feed
PFP LCF
Size specified Size not specified
A4, LT, B5, A5-R, ST-R {-} - [-] {20} 23 [27] {15} 16  [16] {-} - [-] {-} - [-]
A4-R, B5-R, LT-R {-} - [-] {19} 21 [21] {15} 16 [16] {- } - [-] {-} - [-]
B4, LG {-} - [-] {18} 18 [18] {15} 16 [16] {-} - [-] {-}  - [-]
A3, LD {-} - [-] {15} 16 [16] {15} 16 [16] {-} - [-] {-}  - [-]
Paper size Drawer Bypass feed
PFP LCF
Size specified Size not specified
A4, LT, B5, A5-R, ST-R {-} - [-] {20} 23 [27] {15} 16  [16] {-} - [-] {-} - [-]
A4-R, B5-R, LT-R {-} - [-] {19} 21 [21] {15} 16 [16] {- } - [-] {-} - [-]
B4, LG {-} - [-] {18} 18 [18] {15} 16 [16] {-} - [-] {-}  - [-]
A3, LD {-} - [-] {15} 16 [16] {15} 16 [16] {-} - [-] {-}  - [-]
05/11 
						

							1
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES
1 - 3
* System copy speed 
* The system copy speed, including scanning time, is  available when 10 sheets of A4/LT size original 
are set on RADF and one of the copy modes in the ab ove table is selected. The period of time from 
pressing [START] to the paper exit completely out o f the equipment based on the actually measured 
value.
* Upper drawer is selected and copying is at the non -sort mode.
* Automatic copy density, APS/AMS are turned off. 
* Finisher is not installed.  Copy paper
 First copy time ......................... Approx. 5.4  sec. or less
(A4/LT, upper drawer, 100%, original placed manuall y)
 Warming-up time ..................... Approx. 25 sec.  (temperature: 20°C)
 Multiple copying....................... Up to 999 co pies; Key in set numbers
 Reproduction ratio ................... Actual ratio:  100±0.5%
Zooming: 25 to 400% in increments of 1%
(25 to 200% when using RADF)
 Resolution/Gradation............... Scanning: 600 dp i x 600 dpi
Printing: Equivalent to 2400 dpi x 600 dpi 
Gradation: 256 steps
Copy mode Sec.
e-STUDIO200L/202 e-STUDIO230/230L/
232/232S e-STUDIO280/280S/
282/282S
Single-sided originals 
Single-sided copies 1 set
3 sets 
5 sets 34.18 
95.53
154.28 31.5
84.8
136.2 27.6
72.2
114.0
Single-sided originals 
Double-sided copies 1 set
3 sets
5 sets 37.44 
96.81
155.54 34.5
85.9
137.4 31.6
73.4
116.4
Double-sided originals 
Double-sided copies 1 set
3 sets
5 sets 70.26
188.48
306.64 64.8
167.7 
270.6 58.9
143.8
228.5
Double-sided originals 
Single-sided copies 1 set
3 sets
5 sets 64.65
184.73
302.58 57.8
163.1
266.1 50.5
137.3
222.1
Drawer ADU PFP LCF Bypass copy Remarks
Size A3 to A5-R, LD to ST-R,  FOLIO, COMPUTER, 
13LG, 8.5 x 8.5, 8K, 
16K, 16K-R A4, LT A3 to A5-R, LD to ST-R, FOLIO, 
COMPUTER, 13LG, 8.5 x 8.5, 8K,  
16K, 16K-R 
(Non-standard or user-specified 
sizes can be set.)
Weight 64 to 105 g/m2
17 to 28 lb. Bond 64 to 209 g/m
2
, 17 lb. Bond to 110 lb. 
Index
(Continuous feeding) 
50 to 209 g/m 2
, 13 lb. Bond to 110 lb. 
Index 
(Single paper feeding)
Special  paper – Tracing paper, labels,
OHP film 
(thickness: 80 µm or thicker), 
tab paper, envelope
(COM10, Monarch, DL, CHO-3,  
YOU-4) These special papers rec- 
ommended by Toshiba Tec 
CHO-3: 92 mm x 235 mm 
YOU-4: 105 mm x 235 mm
05/11 
						

							e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA  TEC
1 - 4
 Eliminated portion.................... Leading edges : 3.0±2.0 mm, Side/trailing edges: 2.0±2.0 mm (copy )
Leading / trailing edges: 5.0±2.0 mm, Side edges: 5 .0±2.0 mm (print)
 Paper feeding .......................... Standard dra wers:
1 or 2 drawers (stack height 60.5 mm, equivalent to  550 sheets; 
64 to 80 g/m
2 (17 to 22 lb. Bond)): Depends on destinations or 
versions.
PFP: Option (One drawer or two: stack height 60.5 mm, eq uivalent to 
550 sheets; 64 to 80 g/m
2 (17 to 22 lb. Bond))
LCF: Option (Stack height 137.5 mm x 2: equivalent to 25 00 sheets; 
64 to 80 g/m
2 (17 to 22 lb. Bond))
Bypass feeding: Stack height 11 mm: equivalent to 100 sheets; 64 to  80 g/m
2 (17 
to 22 lb. Bond)
 Capacity of originals in the reversing automatic doc ument feeder (Option)
.................................................. A 3 to A5-R, LD to ST-R:
100 sheets / 80 g/m
2 (Stack height 16 mm or less)
 Automatic duplexing unit (ADU is available as stand ard equipment for some destinations or versions.)
.................................................. S tackless, Switchback type
 Toner supply ............................ Automatic t oner density detection/supply
Toner cartridge replacing method (There is a recove red toner supply 
mechanism.)
 Density control......................... Automatic d ensity mode and manual density mode selectable in 1 1 
steps
 Weight ..................................... Approxim ately 75 kg (165.34 lb.): e-STUDIO200L/230/230L/280 /280S
Approximately 77 kg (169.75 lb.): e-STUDIO202/232/2 32S/282/282S 
(include the developer material and drum) (The ADU  and Drawer mod-
ule are installed.)
 Power requirements ................ AC 110 V / 13.2 A , 115 V or 127 V / 12 A
220-240 V or 240 V / 8 A (50/60 Hz)
* The acceptable value of each voltage is ±10%.
 Power consumption ................. 1.5 kW or less (1 15 V series, 200 V series)
* The electric power is supplied to the RADF, (ADU),  Finisher, Job Separator, Offset Tray, PFP and 
LCF through the equipment.
 Total counter ............................ Electronic al counter
05/11 
						

							1
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES
1 - 5
 Dimensions of the equipment ...................... Se e the figure below (W 637 x D 719 x H 739 (mm))
* When the tilt angle of the control panel is 45 deg rees.
 Fig. 1-1
7 1 9
7 3 9
6 3 74 5 °
04/09 
						

							e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA  TEC
1 - 6
1.2 Accessories
Machine version
NAD: North America 
ARD: Argentina
ASD: Central and South America / Hong Kong 
AUD: Australia 
MJD: Europe 
ASU: Asia
SAD: Saudi Arabia
IRD: Iran 
CND: China 
TWD: Taiwan 
JPD: Japan
KRD: Korea
*1: e-STUDIO200L/230/230L/280/280S only 
*2: In e-STUDIO202L/232/232S/282/282S, 2 discs are  included.
Unpacking/setup instruction 1 set 
Operator’s manual 3 pcs. (except for MJD) 
Operators manual pocket 1 pc.
Power cable1 pc.
Warranty sheet 1 pc. (for NAD)
Setup report 1 set (for NAD and MJD)
Customer satisfaction card 1 pc. (for MJD)
Drum (installed inside of the equipment) 1 pc. 
Toner cartridge 1 pc. (except for NAD, MJD)
Developer material 1 pc. (except for NAD, MJD) 
Control panel stopper 1 pc. 
Blind seal 1 pc.
Rubber plug 5 pcs.
CD-ROM 4 pcs. *2
Transfer charger wire cleaner 
(installed inside of the transfer cover) 1 pc.
Paper stopper  *1
1 pc.
Stopper bracket  *1
1 pc.
05/11 
						

							1
June 2004 © TOSHIBA TEC e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES
1 - 7
1.3 Options 
1.3.1 e-STUDIO200L/230/230L/280/280S
* 1) N: North America E: Europe F: France S: Sweden
Notes: 
 The bridge unit (KN-3520) is necessary for install ation of the finisher (MJ-1022, MJ-1025).
 The finisher (MJ-1025) is necessary for installati on of the hole punch unit (MJ-6005N/E/F/S).
 The PCI slot (GO-1040) is necessary for installati on of the scrambler board (GP-1030) and 
parallel interface kit (GF-1140).
 GM-1030/GM-2030/GM-3030 are exclusive for e-STUDIO 200L.
They do not operate with e-STUDIO230/230L/280/280S.
Platen Cover
KA-3511 PC/PC-C
Reversing Automatic Document Feeder (RADF) MR-3016 
Drawer Module MY-1021/-C
Paper Feed Pedestal (PFP) KD-1011/-C 
Large Capacity Feeder (LCF) KD-1012 A4/LT/A4-C 
Finisher (Hanging type) MJ-1022/-C
Saddle stitch Finisher MJ-1025/-C 
Hole Punch Unit MJ-6005 N/E/F/S 
*1
Staple Cartridge STAPLE-1600 (for MJ-1022)
STAPLE-2000 (for MJ-1025)
Bridge Kit KN-3520/-C
Job Separator MJ-5004/-C
Offset Tray MJ-5005/-C
Key copy Counter, Key copy counter socket MU-8, MU-1 0
Work Tray KK-3511
Damp Heater MF-2320 U/E
Fax Board GD-1150 NA/AU/EU/TW/C/AS
2nd Line for Fax Board GD-1160 NA/EU/TW/C
Wireless LAN Adapter GN-1010 
PCI Slot GO-1040/C
Scrambler Board GP-1030 
Printer Kit GM-1020/GM-1030
Printer/Scanner Kit GM-2020/GM-2030 
Scanner upgrade Kit GM-3020/GM-3030 
Parallel interface kit GF-1140 
Desk MH-1700
Harness kit for coin controller GQ-1020 
Automatic Duplexing Unit (ADU) MD-0102 
Slot cover KE-2330
NIC board GF-1150
Data overwrite kit GP-1050
05/11 
						

							e-STUDIO200L/202L/230/232/280/282 SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES June 2004 © TOSHIBA  TEC
1 - 8
1.3.2 e-STUDIO202L/232/232S/282/282S
* 1) N: North America   E: Europe   F: France   S: 
Sweden
Notes: 
1. The bridge kit (KN-3520) is necessary for install ation of the finisher (MJ-1022 or MJ-1025).
2. The saddle stitch finisher (MJ-1025) is necessary  for installation of the hole punch unit 
(MJ-6005N/E/F/S).
3. The PCI slot (GO-1060) is necessary for installat ion of the scrambler board (GP-1040).
4. The antenna (GN-3010) is necessary to enable the  wireless LAN module (GN-1041) and 
Bluetooth module (GN-2010).
5. When the wireless LAN module (GN-1041) and the Bl uetooth module (GN-2010) are 
installed, only 1 antenna (GN-3010) can be connecte d to each.
6. GM-1080U / GM-2080U / GM-4080U are exclusive to e- STUDIO202L. They do not operate 
with e-STUDIO232/232S/282/282S.
Platen Cover
KA-3511PC/-C
Reversing Automatic Document Feeder (RADF) MR-3020 
Automatic Duplexing Unit (ADU) MD-0102 
Drawer module MY-1021/-C 
Slot cover KE-2330
Paper Feed Pedestal (PFP) KD-1011/-C
Large Capacity Feeder (LCF) KD-1012LT/A4/A4-C 
Finisher (Hanging type) MJ-1022/-C 
Finisher (Console saddle stitcher type) MJ-1025
Hole punch unit (for MJ-1025) MJ-6005N/E/F/S
 *1
Staple cartridge STAPLE-1600 (for MJ-1022)
STAPLE-2000 (for MJ-1025)
Bridge kit KN-3520/-C
Job separator MJ-5004/-C
Offset tray MJ-5005/-C
Work tray KK-3511/-C
Damp heater MF-3520U/E
Fax board GD-1150NA/EU/AU/AS/C/TW
2nd line for fax board GD-1160NA/EU-N/C/TW
Printer kit GM-1070/GM-1080U
Printer/Scanner kit GM-2070/GM-2080U 
Scanner kit GM-4070/GM-4080U
Scrambler board GP-1040 
Wireless LAN module GN-1041 
Bluetooth module GN-2010 
Antenna GN-3010
Data overwrite kit GP-1060
PCI slot GO-1060
Desk MH-1700
Harness kit for coin controller GQ-1020
05/11