NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Pag e 6 4
Revision 2.0
CM02
COMMAND CODE
TITLE:
SETTING OF SYSTEM CLOCK
02
MAT
4. DATA TABLE:
1. FUNCTION:
This command is used to assign clock data (day, date and time).
2. PRECAUTION:
(1) The system clock starts when EXE is depressed.
(2) Reenter all the Clock Data if “HARD ERROR” is displayed as a result of this command.
(3) This command is included in MAT mode menu “E1” (Setting of System Clock [COM02]).
3. ASSIGNMENT PROCEDURE:
SECTION NO. DATA MEANING REMARKS
0
[Date (YYYY)]0000 - 9999 The calendar year is set by 4 digits.
1
[Date (MM/DD)]010100 - 123106 Month, Date and Day are set by 2 digits 
each in the order named. Days are set as 
follows:
SUN: 00, MON: 01, TUE: 02, WED: 03, 
THU: 04, FRI: 05, SAT: 06
2
[Time (HH:MM:SS)]000000 - 235959 Hour, Minute, and Second are set by 2 
digits each in the order named.
Hour information is set in military format 
(24-hour). 
For example: 2 p.m. is set as “140000”.
SEC. +02+ +++ +DATAEXE
STDEDESECTION
No.
(0, 1 or 2) (4/6 digits)
MIN.
HR. XX
XXXX
DAY
DATE
MONTH XX
XXXX
[CM02] Setting of System Clock 
						

							ND-45669 (E) CHAPTER 3
Pag e 65
Revision 2.0
CM03
COMMAND CODE
TITLE:
LOG IN/LOG OUT OF PASSWORD MODE
03
Note 1:The password for each level is set by CME9. The allowed commands for each Password Level
are defined with CME7.
Note 2:“OK” is displayed when the login is successful.
Note 3:For security purposes, when entering a password, “*” is displayed.
Note 4:The password mode is automatically logged out unless a command is entered within 10 minutes
after logging in.
1. FUNCTION:
This command is used to enter a password which allows authorized personnel to access commands in
accordance with preassigned authorization levels.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
To log in the password mode and enter the password
+03+ ++++ PASSWORD PASSWORD LEVEL (0 - 7)
EXE
STDEDE
+03+ + + +
+ CCCCCCCC 9
EXE
STDEDE(1 digit)
(Max. 8 digits)
To log out of the password mode
8 digits
[CM03] Log In/Log Out of Password Mode 
						

							CHAPTER 3 ND-45669 (E)
Page 66 Addendum-001
Revision 2.1 AUGUST, 1998
CM04
COMMAND CODE
TITLE:
LANGUAGE INDICATED ON MULTILINE TERMINAL LCD
04
INITIAL
4 . D ATA  TA B L E :
1. FUNCTION:
This command selects the language that displays on the Multiline Terminal LCDs.
2. PRECAUTION:
This command requires a system reset after setting the data.
3. ASSIGNMENT PROCEDURE:
: Initial Data
Y1 S T  D ATA 2 N D  D ATA
DATA MEANING DATA MEANING
00 00 Selected language for Multiline Terminal 
LCD0
1
2
7Japanese
English
French
Depends on Nation Code
(Japanese/English)
+ 04YY
++
++
+ 1ST DATA
EXESTDEDE
(2 digits)2ND DATA
(1 digit)
[CM04] Language Indicated on Multiline Terminal LCD 
						

							ND-45669 (E) CHAPTER 3
Addendum-001 Page 67
AUGUST, 1998 Revision 2.1
CM05
COMMAND CODE
TITLE:
CARD ASSIGNMENT
05
MAT
4. DATA TABLE:
1. FUNCTION:
This command is used to inform the main processor card (CP00 or CP03) of the SENSE switch (sense
wheel) setting on each AP circuit card that is installed.
2. PRECAUTION:
(1) This command requires a system reset after setting the data.
(2) This command is included in MAT mode menu “E2” (Board Assignment [COM02]).
3. ASSIGNMENT PROCEDURE:
: Initial Data
SENSE 
WHEEL
(AP NO.)SETTING DATA
RELATED
COMMANDREMARKS
DATA MEANING
04 – 15 04 Hotel/SMDR/Centralized Building–CCIS
(PN-AP00-A)
07 Authorization Code, Forced Account Code,
OAI (PN-AP01)
08 MF Receiver Trunk (PN-4RSTB/
PN-4RSTC)/911 Sender Trunk (PN-4RSTB)
09 DTI (PN-24DTA/PN-24DTA-A/PN-30DTC/
PN-30DTC-A)
10 BRI (PN-BRTA/PN-2BRTC)
11 Common Channel Handler (PN-SC00)
12 D Channel Handler (PN-SC01)
13 ISDN Channel Handler (PN-SC02/SC03)
15 This slot is not used.
19 Memory Expansion Card (PN-ME00)
23 ZT Handler (PN-SC03)
34 Data Base Module (DBM) (PN-AP00-A)
35 D Channel Handler for Roaming (PN-SC01)
+05++
++
+ SENSE WHEEL
EXESTDEDE
(2 digits)DATA
(2 digits)
[CM05] Card Assignment 
						

							CHAPTER 3 ND-45669 (E)
Page 68 Addendum-001
Revision 2.1 AUGUST, 1998
CM05
COMMAND CODE
TITLE:
CARD ASSIGNMENT
05
MAT
Note:Set the SENSE switch on the AP circuit card to match an unequipped slot number as shown below.
SENSE WHEEL (04 - 15)04 05 06 07 08 09 10 11 12 13 14 15
SWITCH SETTING VALUE456789ABCDEF 
						

							ND-45669 (E) CHAPTER 3
Pag e 69
Revision 2.0
CM06
COMMAND CODE
TITLE:
MISC. TRUNK NUMBER ASSIGNMENT
06
4. DATA TABLE:
1. FUNCTION:
This command assigns Miscellaneous Trunk Numbers to each card.
2. PRECAUTION:
This command requires a system reset after setting the data.
3. ASSIGNMENT PROCEDURE:
YY MISC. TRUNK NO. AP NUMBER + CIRCUIT NUMBERRELATED
COMMAND
04 00 ~ 15 MF Receiver /911 Sender
Trunk 00 – 15XXX XX
X
Circuit Number 
(0 – 3)
Slot Number 
(04 – 15) assigned by 
CM05
CM05
07 0 ~ 3 CCH (Common Channel Han-
dler) Number 0 ~ 3XX XX
Slot Number 
(04 – 15) of 
PN-SC00
CM05
CM30
CM35
CMA7, CMA8
08 0 ~ 4 DCH (D Channel Handler) 
Number 0 ~ 4XX XX
Slot Number 
(04 – 15) of 
PN-SC01
CM05
CM35 YY = 93
09 00 ~ 11 ICH (ISDN Channel Handler) 
Number 00 ~ 11XX
XX
Slot Number 
(04 – 15) of 
PN-SC02/PN-SC03
CM05
10 XX XX Slot Number (04 – 15) of PN-
SC03
+
D Channel Block Number
(00 – 03)XXXX XXXX
LEN of PN-2CSI
(0000, 0004-0504,
0508)
CM05
 + 06YY +   +   +   +   + STDE1ST DATA
(1-4 digits)DE2ND DATA
(2-4 digits)EXE
[CM06] Misc. Trunk Number Assignment 
						

							CHAPTER 3 ND-45669 (E)
Page 70 Addendum-002
Revision 2.2 JANUARY, 1999
CM07
COMMAND CODE
TITLE:
DTI TRUNK/ISDN TRUNK ASSIGNMENT
07
4 . D ATA  TA B L E :
1. FUNCTION:
This command assigns the DTI/ISDN trunks.
2. PRECAUTION:
This command requires a system reset after setting the data.
3. ASSIGNMENT PROCEDURE:
YY1S T DATA 2ND DATA
RELATED
COMMAND
DATA MEANING DATA MEANING
01 XXXX Channel No. of 24-DTI/30-DTI
XX
XX
Channel No.
for 24-DTI: 00-23
for 30-DTI: 01-15, 16-31
Slot Number assigned by 
CM05
DXXX Trunk Number
(D000 – D255)
Note:Trunk numbers
already assigned by
CM10 cannot be
used.CM05 
CMA9 YY=00
02 XXXX Channel No. of BRT
XX
XX
Channel No.
for PN-BRTA: 00/01
for PN-2BRTC: 00-03
Note:Be sure to assign
the trunk numbers to
all circuits (00-03) of
the PN-2BRTC card,
even if only one PCM
digital line is accom-
modated to the card.
Set make-busy to the
unused trunk numbers
by CME5 Y=1.
Slot Number assigned by 
CM05
DXXX Trunk Number
(D000 – D255)
Note:Trunk numbers
already assigned by
CM10 cannot be
used.CM05
+ 07YY
++
++
+ 1ST DATA
EXESTDEDE
(4 digits)2ND DATA
(4 digits) 
						

							ND-45669 (E) CHAPTER 3
Addendum-002 Page 70-1
JANUARY, 1999 Revision 2.2
CM07
COMMAND CODE
TITLE:
DTI TRUNK/ISDN TRUNK ASSIGNMENT
07
YY1S T DATA 2ND DATA
RELATED
COMMAND
DATA MEANING DATA MEANING
05 32XX Virtual Channel No.
32 XX
Home-Side Trunk 
Virtual Channel
No. 00 – 30 (Even No.)
Mate-Side Trunk
Virtual Channel
No. 01 – 31 (Odd No.)
DXXX Trunk Number
(D000 – D255)
Note:Trunk numbers
already assigned by
CM10 cannot be
used. 
						

							THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E)
Page 70-2 Addendum-002
Revision 2.2 JANUARY, 1999
This page is for your notes. 
						

							ND-45669 (E) CHAPTER 3
Pag e 71
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
1. FUNCTION:
This command is used to assign basic features on a system-wide basis.
2. PRECAUTION:
After setting 1st data 390 and 391, system reset is required.
3. ASSIGNMENT PROCEDURE:
   +   08  +  +    +  +    + STDEBASIC SERVICE 
FEATURE 
(3 digits)DEDATA (0/1)
(1 digit)EXE
[CM08] Basic Service Features