NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Pag e 1 62
Revision 2.0
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
4. DATA TABLE:
: Initial Data
YY/YYY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
00
(TK)Kind of Trunk Route 00
01
02
03
04
05
06
15 DDD (C.O., DID) Trunk/ISDN Trunk
FX Trunk
WATS Trunk
CCSA Trunk
TIE (Tie Line) Trunk
Paging Trunk/Interface with BGM Tone 
Source and Wake-Up Announce
Not used
01
(PBDP)Dialing Signal Type 0
1
2
3
4
5
6
7 [Call Termination]
[Call Origination]
DP DP
DTMF DTMF
DP/DTMF DTMF
02
(OGIC)Call Direction 0
1
2
3 Incoming Trunk
Outgoing Trunk
Bothway Trunk
03
(NAME)Trunk Name Number 00
14
15 
16
63Trunk Name 00
Trunk Name 14
Kind of Trunk Route assigned by CM35
YY = 00 is displayed.
Trunk Name 16
Trunk Name 63CM77 
Y = 2, 3
Local Office Code
Table Number used for tan-
dem connection
(For Enhanced 911)00
14
15 
63Local Office Code Table No. 00-14
Not send calling number
~
~
~
~
~
~
~ 
						

							ND-45669 (E) CHAPTER 3
Pag e 1 63
Revision 2.0
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
04
(ANS)Application of answer signal 
from the distant office for out-
going connection.0
1
2
3
4
7 Battery Reversal (C.O. line)
Answer Signal arrives (Tie line/ISDN) 
Answer Signal does not arrive 
(Polarity Reversal is ignored and 
Answer timing shall be set by CM41
Y=0 Function No. 03)
Answer Signal does not arrive (Tie line/
C.O. Line, Answer timing shall be set by 
CM41 Y = 0 Function No. 03)
05
(RLS)Application of release signal 
from the distant office for an 
outgoing connection or an in-
coming connection0
1 Release signal does not arrive 
(Ground Start/Loop Start C.O. without
Release Signal)
Release signal arrives 
(Tie line/Ground Start/Loop Start with
Release Signal/DID)
08
(DIAL)Sending the dial pulse on an 
outgoing call1
2
3 No dial pulses are sent out 
(Speaker Paging)
Dial pulses are sent out: For test
(Release the resister/sender when the calling 
station is on-hook)
Dial pulses are sent out (C.O. line/Tie Line/
Radio Paging)
09
(SIGI)Incoming Connection Signal-
ing00
01
02
03
04
05
06
07
08
15 Ring Down (Ground Start C.O.)
Wink Start
Delay Dial
Immediate Start
2nd DT/Timing Start–Tie Line
ISDN Indial
Ring Down (Loop Start C.O.)CM35 YY = 20
10
(DT)2nd DT Sending on Call Ter-
mination0
1 2nd DT is not sent (DID, etc.)
2nd DT is sent
: Initial Data
YY/YYY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
~ 
						

							CHAPTER 3  ND-45669  (E)
C M 35
MAT
11
Ra dio Pag ing TRK
De termin ed  by   2 dig it s  +  S T N
~~ 
						

							ND-45669 (E) CHAPTER 3
Pag e 1 65
Revision 2.0
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
15
(ICI)Kind of Call Termination Indi-
cator Key/Lamp on ATTCON. 
With respect to incoming calls 
of the same kind (C.O. Incom-
ing Calls, Tie Line 
Incoming Calls), Call Termi-
nation Indicator lamps on the 
ATTCON, the kinds of incom-
ing calls are further catego-
rized. 
Note 1:When standard lamp 
indications are uti-
lized, assign data for 
standard assign-
ment for each incom-
ing call.
Note 2:Correspondence be-
tween key positions 
on the ATTCON and 
the assignment data 
should be assigned 
in CM90.00
01
02
03
04
05
06
07
10
11
12
13
14
15
16
17
20
21
22
23
24
25
26
27
30
31
32
33
34
35
36
37
40
41
42
43
44
45
46
47
75C.O. Incoming 0 (Standard “LDN” key)
C.O. Incoming 1
C.O. Incoming 2
C.O. Incoming 3
C.O. Incoming 4
C.O. Incoming 5
C.O. Incoming 6
C.O. Incoming 7
FX Incoming 0 (Standard “FX” key)
FX Incoming 1
FX Incoming 2
FX Incoming 3
FX Incoming 4
FX Incoming 5
FX Incoming 6
FX Incoming 7
WATS Incoming 0 (Standard “WATS” key)
WATS Incoming 1
WATS Incoming 2
WATS Incoming 3
WATS Incoming 4
WATS Incoming 5
WATS Incoming 6
WATS Incoming 7
CCSA Incoming 0 (Standard “CCSA” key)
CCSA Incoming 1
CCSA Incoming 2
CCSA Incoming 3
CCSA Incoming 4
CCSA Incoming 5
CCSA Incoming 6
CCSA Incoming 7
Tie Line Incoming 0 (Standard “TIE” key)
Tie Line Incoming 1
Tie Line Incoming 2
Tie Line Incoming 3
Tie Line Incoming 4
Tie Line Incoming 5
Tie Line Incoming 6
Tie Line Incoming 7
Call Termination via No. 7CCISCM90
CM50
: Initial Data
YY/YYY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING 
						

							CHAPTER 3 ND-45669 (E)
Pag e 1 66
Revision 2.0
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
16
(SHF)Sending of Hook Flash to out-
side0
1 Not sending
SendingCM90 YY = 00
DATA = F1009
CM41 Y = 2
Function No. = 
17
17
(SKP)Digit addition and deletion at 
the time of a Tie Line Incom-
ing Call: On an incoming call 
from a Tie Line, if number of 
digits arriving from distant of-
fice does not coincide with 
number of digits of a station 
number, the number of digits 
is to be adjusted by this data 
assignment.00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15 “0” Add
“1” Add
“2” Add
“3” Add
“4” Add
“5” Add
“6” Add
“7” Add
“8” Add
“9” Add
2-digit addition 
(CM50 YY = 00, 1st Data: 0)
1 digit deletion
2 digits deletion
Addition/deletion not performed
18
(DID)Digit conversion on DID call 0
1 To provide
Not providedCM76
19
(PAD)PAD Control of C.O. Line or 
Tie line0
1
2
3
4
5
6
7 Programmable PAD
(See CM42)
Fixed PAD
(See PRECAUTION [1])CM42
20
(SNDS)Sender Start Condition 00
01
02
14
15 Wink Start
Delay Dial
Ground Start
Timing Start (Prepause per YY = 21)CM35
YY = 09
: Initial Data
YY/YYY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
~ 
						

							ND-45669 (E) CHAPTER 3
Pag e 1 67
Revision 2.0
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
21
(PPT)Sender Prepause Timing 00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15 0 sec
0.5 sec
1.0 sec
1.5 sec
2.0 sec
2.5 sec
4.0 sec
5.0 sec
6.0 sec
7.0 sec
8.0 sec
9.0 sec
10.0 sec
11.0 sec
12.0 sec
3.0 secCM08-193, 
194, 331
CM35 YY = 43
22 Automatic Live Recording 
Activation0
1 Start automatically
Not available
Note:When this command is activated,
data assignments must also be
made in CM08-141, CM35, YY =
22, and/or CM76, Y = 8.
23
(IDDP)DP Inter-Digital Pause 0
1
2
3
4
5
6
7 300 ms
400 ms
500 ms
600 ms
700 ms
900 ms
1100 ms
800 ms
24
(IDPB)DTMF-Inter-Digital Pause 0
1
2
3
4
5
6
7 32 ms
64 ms
80 ms
96 ms
160 ms
192 ms
240 ms
128 ms
25
(DPLS)DP Make Ratio 0
1 39 % Make Ratio
33 % Make Ratio
26
(PBLS)DTMF Signal Width 0
1 64 ms
128 ms
: Initial Data
YY/YYY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING 
						

							CHAPTER 3  ND-45669  (E)
C M 35
MAT
28
~
~~ 
						

							ND-45669 (E) CHAPTER 3
Pag e 1 69
Revision 2.0
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
44
(S2DC)Trunk Access Code sent to 
SMDR for outgoing call000
 or 
999When a trunk is seized by a Trunk 
Appearance key or LCR, one or two-digit 
code (00-99) is sent out to the SMDR.
45
(RDP)DP sender release timing 0
1
2
3
4
5
6
7 2 sec
4 sec
6 sec
8 sec
12 sec
14 sec
16 sec
10 sec
46
(RPB)DTMF sender release timing 0
1
2
3
4
5
6
7 2 sec
4 sec
6 sec
8 sec
12 sec
14 sec
16 sec
10 sec
48 Sending Busy/Idle informa-
tion to network0
1 Not available
Available
49
(SMDI)SMDR/Centralized Billing-
CCIS for Incoming Call0
1 To provide
Not providedCM13 YY = 05
51
(ORCA)Restriction of Outgoing Con-
nection
(Unrestricted) (RCA)0
1 Restricted
AllowedCM12 YY = 01
52
(ORCB)Restriction of Outgoing
Connection
(Non-Restricted-1) (RCB)0
1 Restricted
Allowed
53
(ORCC)Restriction of Outgoing
Connection
(Non-Restricted-2) (RCC)0
1 Restricted
Allowed
54
(ORCD)Restriction of Outgoing 
Connection
(Semi-Restricted-1) (RCD)0
1 Restricted
Allowed
55
(ORCE)Restriction of Outgoing 
Connection
(Semi-Restricted-2)0
1 Restricted
Allowed
: Initial Data
YY/YYY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
~~ 
						

							CHAPTER 3  ND-45669  (E)
C M 35
MAT
56 
						

							ND-45669 (E) CHAPTER 3
Pag e 1 71
Revision 2.0
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
69
(AN0)Announcement Service 
Group 00
1 Restricted
AllowedCM20, 
A03-A09
CM49
YY = 00 – 
04XX
CM15
YY = 34 – 39 70
(AN1)Announcement Service 
Group 10
1 Restricted
Allowed
71
(AN2)Announcement Service 
Group 20
1 Restricted
Allowed
72
(AN3)Announcement Service 
Group 30
1 Restricted
Allowed
73
(AN4)Announcement Service 
Group 40
1 Restricted
Allowed
74
(VRAN)Attendant Delay Announce-
ment0
1 Allowed
RestrictedCM49
YY = 00, 0A
75 DID incoming LDN display 
on Multiline Terminal/
ATTCON0
1 Available
Not available (Trunk ID code 
assigned by CM30 YY=19 is 
displayed.)
Note 1:Up to 4 digits LDN are avail-
able.
Note 2:The DID incoming LDN is
displayed irrespective of any
digit conversion by CM76.CM30
YY = 19
76
(DCP)Designation of Area Code De-
velopment Pattern No. for Toll 
Restriction Analysis, and 
Maximum Digit Analysis.00
07
15 Area Code Development Pattern No. 0
Area Code Development Pattern No. 7
Not usedCM8A 
YYY = 400 – 
407 
CM85
Y = 0 – 7
78 Digit conversion of leading 
2 – 4 digits of DID incoming 
LDN0
1 Available
Not available (All digits of DID incoming 
LDN are converted by CM76).CM35 
YY = 12, 18 
CM76
83
(SER)Trunk Seizing Sequence 0
1 Begin from lowest numbered trunk
By allotterCM08-078
86
(CTX)Centrex Trunk 0
1 To provide
Not provided
: Initial Data
YY/YYY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
~~