NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Pag e 7 2
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
4. DATA TABLE:
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
012 Busy Verification 0
1
 
Not available
Available
014 Attendant Loop Release 0
1
 
Provided
Not provided
018 When the system is in night mode, an attendant (dial “0”) call 
from a station is automatically transferred to a specific sta-
tion.0
1
 
Not transferred
To transfer
(See CM51 YY = 13)
021 Station to Station call during a C.O. outgoing connection or 
outgoing call transfer.0
1
 
To restrict
Not restricted
025 MSG Display 0
1
 
MSG (only)
MSG X (X: No. of message)
026 Group Diversion 0
1
 
Available (See CM16 Y = 2)
Not available
028 C.O. to C.O. transfer by station or attendant.
Note:This data is effective for C.O. Trunks (Ground
Start/Loop Start) which receive a release signal
from the C.O.0
1
 
To allow
Not allowed
029 When tandem call duration passes a predetermined time, the 
call is disconnected or continued.0
1
 
To disconnect
To continue
032 When a dial-in incoming call from a tie line or DID line is ad-
dressed to vacant levels or unassigned stations, the call is 
routed to a predetermined station, ATTCON or Digital An-
nouncement Trunk.0
1
 
Restricted (Reorder)
Predetermined station, ATTCON, or 
Digital Announcement Trunk assigned 
by CM51 YY = 06, 07
035 Toll Restriction for an outgoing call by Station Speed Dialing 
feature.0
1
 
Not provided
To provide
036 Buzzer indication when a call remains held at the ATTCON 
over a preprogrammed period of time assigned by CM41 Y = 
0, Function No. 00 
(Buzzer indication for Automatic Recall)0
1
 
Not available
Available
037 Select the detection method of IC GS Trunks Ring signal.
Note:This is useful when AC induction is present on GS
Trunks.0
1Detect only, Ring cycle only
Detect Ring cycle and Ground Lead
040 SMDR output for Tandem Call 0
1 Available
Not available
043 System Speed Dialing Security (Stored Number display on 
Multiline Terminal for an outgoing call by System Speed 
Dialing).0
1 Not displayed
Display 
						

							ND-45669 (E) CHAPTER 3
Page 73
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
044 Toll Restriction for outgoing call by System Speed Dialing 
feature.0
1 Not provided
Provide
045 Warning tone sent to connected parties during Executive 
Override or Attendant Override.0
1 Only once
Every 4 sec.
048 Passing Dial Tone facility 0
1 Not available
Available
050 If * button on DTMF telephone is pressed while hearing busy 
tone, it is regarded as a Switch Hook Flash.0
1 Effective
Ineffective
051 If # button on DTMF telephone is pressed while hearing busy 
tone, it is regarded as a Switch Hook Flash.0
1 Effective
Ineffective
053 Alternative ISDN line for Event Based CCIS 0
1 Available
Not available
055 Result of a Switch Hook Flash on a telephone that belongs to 
House Phone Group 0 or 1.0
1 Special Dial Tone (Dialing is
available)
Attendant Recall
056 Result of a Switch Hook Flash on a telephone that belongs to 
House Phone Group 2 or 3.0
1 Special Dial Tone (Dialing is
available)
Attendant Recall
057 Result of a Switch Hook Flash on a telephone 
assigned as a Hot Line.0
1 Special Dial Tone (Dialing is
available)
Attendant Recall
058 Destination selection method for Day/Night Mode Change, 
when Direct Inward Dialing terminates.
Effective only when the 2nd data of CM08-264 is 1.0
1 For station tenant
For trunk tenant
062 Call transfer from a station before called station answers. 0
1 Not available
Available
063 Call transfer from a station before called ATTCON answers. 0
1 Available
Not available
067 Attendant Overflow 0
1 Available
Not available
068 Camp-On Tone sending to a busy station by Camp-On Trans-
fer method0
1 Camp-on Tone sent out only once
Camp-on Tone repeats at 4 second
intervals.
069 When a station user has dialed any one digit while hearing 
busy tone0
1 Switch Hook Flash
Step Call
076 Warning tone to be sent to C.O. line, when a station or opera-
tor overrides a busy station connected to a C.O. line0
1 Not sent 
Send
: Initial Data
BASIC SERVICE FEATURE SETTING DATA 
						

							CHAPTER 3 ND-45669 (E)
Page 74 Addendum-001
Revision 2.1 AUGUST, 1998
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
078 This setting determines the trunk seizing sequence when CM 
35 YY = 83 is set to 0.
Note:When NEAX 2000/1000IVS is installed with loop-
start trunks, it is important to select the highest
available trunk setting to prevent call collisions. 0
1 Highest available trunk
Lowest available trunk
085 Types of PS No-Answer timer 0
1 No Answer timer (CM41 • Y = 0-86)
No Answer timer (CM41 • Y = 0-01)
086 Whether PS Out of Cell/PS Power Off are separated from No-
Answer.
Note:This data is effective only when CM08-086 is set to
0.0
1 Separated
Not separated
(Handled as No-Answer)
088 Whether the Home PBX Numbering Plan is the Open Num-
bering System or Closed Numbering System.0
1 Closed Numbering System
Open Numbering System
094 Paging access tone sent to station 0
1 Send
Not sent 
095 Hook flash (break pulse) sent to Radio Paging equipment 
from station0
1 Send
Not sent 
096 Hook flash (break pulse) sent to Speaker Paging equipment 
from station0
1 Send 
Not sent 
101 When data for “102” is “0” (For Single Line Telephone) 0
1 The call with STA-B is disconnected, 
and STA-A returns to STA-C.
Three-Party Conference
102 When the station (STA-A), after holding the other station 
(STA-C), has made a switch hook flash while talking with an-
other station (STA-B).
This data is applied to single line telephone station.0
1 See the data for “101”.
STA-B is held, and STA-A returns to 
the connection with STA-C.
(Broker’s Call)
103 When the station (STA-A), after holding a C.O. call, has 
made a switch hook flash while talking with another station 
(STA-B).0
1 See the data for “104”.
STA-B is held, and STA-A returns to 
the connection with the C.O. line.
(Broker’s Call)
104 When the data for “103” is “0” 0
1 The call with STA-B is disconnected, 
and STA-A returns to the C.O. line.
Three-Party Conference
109 Periodic record tone on live record 0
1 Send
Not sent  
						

							ND-45669 (E) CHAPTER 3
Addendum-001 Page 74-1
AUGUST, 1998 Revision 2.1
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
110 1000-Slot Memory Block Number “3” for Station Speed Di-
aling is used as the Memory Block for System Speed Dialing.0
1 Available (See CM20, A50)
Not available
111 1000-Slot Memory Block Number “1” for Station Speed Di-
aling is used as the Memory Block for System Speed Dialing.0
1 Available (See CM20, A51)
Not available
112 1000-Slot Memory Block Number “0” for Station Speed Di-
aling is used as the Memory Block for System Speed Dialing.0
1 Available (See CM20, A52)
Not available 
						

							THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E)
Page 74-2 Addendum-001
Revision 2.1 AUGUST, 1998
This page is for your notes. 
						

							ND-45669 (E) CHAPTER 3
Pag e 75
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
113 Outgoing C.O. Line Call from a Station to Station connection. 0
1 Not allowed
To allow
114 Answer preference for enhanced Trunk Direct Appearance 0
1 Display 2-digit trunk ID code (CM30 
YY = 19, last two digits assigned)
Display 4-digit trunk ID code (CM30 
YY = 19)
115 A station user is allowed to break into a call between a C.O. 
line party and another station by Executive Override.0
1 Not allowed
To allow
116 Answer Key rings
Note:Answer key rings on TAS and Pooled Line.0
1 To provide
Not provided
117 While the station (STA-A) is talking with another station 
(STA-B), after consultation hold with a C.O. call. When STA-
B has hung up.0
1STA-A returns to the call with the C.O. 
line.
STA-A hears ROT.
119 Toll Diversion
When the station dials restricted area code after C.O. Trunk 
Access code.0
1 Diversion to attendant “ICPT”
The station receives Reorder Tone
120 GUEST NAME DISPLAY
(time to display on LCD)
Note:This data is only available when CM08-128 = 0.0
1 10 sec.
6 sec.
121 GUEST NAME DISPLAY
Note:This data is only available when CM08-128 = 0.0
1 Duration of Call
CM08 - 120
123 When a station has originated a call to C.O. line via the trunk 
route assigned to 1 by CM35 YY = 04, and answer signal has 
not been detected within the preprogrammed time after dial-
ing, a pseudo-answer signal is generated. (CM41 Y = 0, Func-
tion No. 03)0
1
 
Not sent
To send
124 Multi-Connection of Digital Announcement Trunk on An-
nouncement Service.0
1
 
Available
Not available 
(Single Connection)
125 After holding an incoming C.O. call, an attendant dials a sta-
tion. If, after connection with the attendant, the called station 
goes on-hook, the attendant hears Reorder Tone or returns to 
the held call.0
1
 
Return to held call
Reorder tone
128 Guest Name Display via PMS. 0
1
 
Available
Not available
130 Exclusive Hold (E-HOLD) Service on Multiline Terminal. 0
1
 
Not available
Available
: Initial Data
BASIC SERVICE FEATURE SETTING DATA 
						

							CHAPTER 3 ND-45669 (E)
Pag e 7 6
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
133 A trunk line placed in Consultation Hold by Call Park-Sys-
tem/Tenant, can be retrieved by pressing a trunk line appear-
ance key on any Multiline Terminal.0
1
 
Not available
Available
135 Periodic Time Indication Tone Sending for C.O. Line connec-
tion. (CM41 Y = 0, Function No. 09)0
1
 
To send 
Not sent 
136 Periodic Time Indication Tone Sending for a Tie Line con-
nection (When the data for 135 of CM08 is 0).0
1
 
To send 
Not sent 
137 Ringing Signal for a station call with a trunk line placed in 
Consultation Hold.0
1
 
Change from Internal to External 
Ringing when caller goes on-hook or 
presses RLS key (CM08-138)
External Ringing
(CM35 YY = 33)
138 Ringing signal for a Station to Station Connection. 0
1
 
2s ON - 4s OFF
1s ON - 2s OFF
139 Individual Trunk Access from a station. 
(CM20-081)
(Where data is set as “0”, ORT and SENDER are not being 
timed out. Set data as “1” normally.)0
1
 
For testing
Normal
141 To record Station to Station calls automatically 0
1
 
Starts automatically
Not available
142 Attendant access capability provided from the stations be-
longing to a tenant with no ATTCON.0
1
 
To allow
Not allowed
143 Calling the designated ATTCON from a station within anoth-
er tenant is restricted (CM20 - 095)0
1
 
To restrict
Not restricted
(Recall transferring station)
145 Outgoing call preset or Call answer preset of Multiline Termi-
nal
• Outgoing preset:   +  
• Call answer preset:    +  0
1
 
Available
Not available
146 Transferred C.O. call to a busy station is automatically 
Camped-on when transferring station goes on-hook.0
1
 
Available
Not available
(Recall transferring station)
147 When a station transferring a C.O. call to a station, which is 
busy, has performed a switch hook flash.0
1
 
Special Dial Tone, allowing the use of 
Camp-On access code.
Return to C.O. line call
148 When a station user, upon encountering the called station 
busy, has dialed the same last digit again while hearing busy 
tone.
(Effective only when data for “069” is “1”.)0
1
 
Switch Hook Flash
Ineffective
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
FNCOG
FNCANS 
						

							ND-45669 (E) CHAPTER 3
Addendum-002 Page 77
JANUARY, 1999 Revision 2.2
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
149 In delay-type paging, when the paged party encounters a busy 
paging circuit, Call Back is automatically set. (Applicable to 
both Radio Paging and Speaker Paging.)0
1
 
To set
Not set
150 Restriction of a station to station call between tenants by 
CM63 Y=1 is temporarily cancelled by external key.0
1
 
To cancel
Not cancelled
151 Dialing 1 for switch hook flash (DP Telephone) / switch hook 
flash (DTMF / DP Telephone).0
1
 
Not available
Available
153 Howler Tone sent to locked-out stations. 0
1
 
Not sent
To send
155 When a station user dials the digit “1” upon encountering a 
trunk busy.0
1
 
Switch Hook Flash
Ineffective
156 Dialing of a Single Digit Feature Access Code while the call-
ing station hears RBT or performs a Voice Call.0
1
 
To allow
Not allowed
157 Whether the Paging Answer code and the Paging Access code 
are to be the same or not.
If codes are the same, paging access codes must be set to trunk 
routes (in CM30 YY=00), as follows:
Paging Answer Zone 0 : Trunk Route 50
9 : Trunk Route 59
CM20, 1st data=070 – 079, are used to set the combined
access/answer codes.0
1
 
Same
Different
158 All Zone Internal Paging. 0
1
 
Not available
Available
161 Transfer a trunk line placed in Consultation Hold. (Hold 
Transfer)0
1
 
Available (Hold Transfer)
Not available (Consultation Hold)
162 If the multiple Radio Paging access is available after access-
ing a Radio Paging Trunk with delay type Radio Paging.0
1
 
Not available
Available
163 Step Call for an Incoming Call from a Tie Line. 0
1
 
Not available
Available
165 Replaying of a message recorded in the Digital Announce-
ment Trunk for Attendant Delay Announcement.0
1
 
The message is replayed at an interval. 
(See CM41 Y=0, Function No. 47)
The message is replayed only once.
168 When the DTMF station or Multiline Terminal station dials 
“#” during the setting of Station Speed Dialing feature.0
1
 
“#” is set as paused data (1.5 sec.)
“#” is set as called number to C.O. line.
~~ 
						

							ND-45669 (E) CHAPTER 3
Addendum-002 Page 70-1
JANUARY, 1999 Revision 2.2
CM07
COMMAND CODE
TITLE:
DTI TRUNK/ISDN TRUNK ASSIGNMENT
07
YY1S T DATA 2ND DATA
RELATED
COMMAND
DATA MEANING DATA MEANING
05 32XX Virtual Channel No.
32 XX
Home-Side Trunk 
Virtual Channel
No. 00 – 30 (Even No.)
Mate-Side Trunk
Virtual Channel
No. 01 – 31 (Odd No.)
DXXX Trunk Number
(D000 – D255)
Note:Trunk numbers
already assigned by
CM10 cannot be
used. 
						

							THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E)
Page 70-2 Addendum-002
Revision 2.2 JANUARY, 1999
This page is for your notes.