NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Page 78 Addendum-002
Revision 2.2 JANUARY, 1999
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
176 1000-Slot Memory Block Number “2” for Station Speed Di-
aling is used as the Memory Block for System Speed Dialing.0
1
 
Available
Not available
177 Last Number Redial feature for DP/DTMF telephone. 0
1
 
Available (See CM20 - 069)
Not available
178 Last Number Redial/Stack Dial for internal calls 
(effective only when data 177 is set to 0.)0
1
 
Not available (only available for exter-
nal calls)
Available
179 Ringing cadence on Direct in Termination call. 0
1
 
As per CM35 YY = 33
0.4s ON - 0.2s OFF -
0.4s ON - 2s OFF
180 Ringing cadence on DID call, DISA call and Automated At-
tendant call.0
1
 
0.4s ON - 0.2s OFF -
0.4s ON - 2s OFF
As per the data of CM35 YY = 33
181 Multiline Terminal one-touch calling or DSS key calling 
while another party is being rung, or while talking with anoth-
er party.0
1
 
Not available
Available
183 Music selection on the MP card. 0
1
 
Nocturne
Minuet
185 When the transferring station goes on-hook before the called 
station answers for Call Transfer-All Calls service, if the 
transferred call remains unanswered for a preprogrammed du-
ration, the transferring station is recalled. 
(Recall Timing: CM41 Y = 0, Function No. 07)0
1
 
Not available
Available
187 Recall priority over Call Forwarding 0
1
 
Recall is higher
Call Forward is higher
193 Sender Prepause for C.O. outgoing call
(Not used with LCR)0
1
 
To provide
Not provided
194 Sender Prepause for Tie Line outgoing call 0
1
 
Not provided
To provide
199 For the operation of Line Preselection on a Multiline Termi-
nal, the SPEAKER button is required after depressing the de-
sired LINE/TRUNK button.0
1
 
Not required
Required
200 Wake-up time printout on the H/M printer and the report is 
sent to the PMS, when setting a wake-up time from a guest 
station.0
1
 
Available
Not available
201 Do Not Disturb records printout on the H/M printer and the 
report is sent to the PMS, when setting Do Not Disturb from 
a guest station.0
1
 
Available
Not available 
						

							ND-45669 (E) CHAPTER 3
Addendum-001 Page 79
AUGUST, 1998 Revision 2.1
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
204 Diversion display by ATTCON. 0
1
 
Available
Not available
205 LDN Diversion by ATTCON.
(See CM58)0
1
 
Available
Not available
206 Trunk to Trunk Transfer by an Attendant before answer (on 
the OG trunk).0
1
 
Available
Not available
208 Dialing of a Single Digit Feature Access Code, while the call-
ing station hears busy tone.0
1
 
Available
Not available
212 When a caller encounters all ACD/UCD stations busy. 0
1
 
Busy Tone is to be sent out.
Caller is placed into queuing mode.
214 When an ACD/UCD station dials the ACD/UCD Busy out 
code after holding the call from a Tie Line or CCSA line. 
(See CM17 Y = 6)0
1
 
ACD/UCD station hears Service Set 
Tone, and returns to the call by Switch 
Hook Flash.
The call is disconnected. 
ACD/UCD station hears ROT.
215 When an ACD/UCD station dials the ACD/UCD Busy out 
code after holding the call from a C.O. Line (DDD/FX/
WATS). 
(See CM17 Y = 5)0
1
 
ACD/UCD station hears Service Set 
Tone, and returns to the call by Switch 
Hook Flash.
The call is disconnected. 
ACD/UCD station hears ROT.
216 Designation of the processor to be checked for Authorization 
Code/Forced Account Code.0
1
 
MP (PN-CP00) Basic (CM2A Y= 0-4)
AP (PN-AP01)
217 Designation of the processor to be checked on a Direct Inward 
System Access (DISA ID Codes).0
1
 
MP (PN-CP00) Basic (CM2A Y= 5-8)
AP (PN-AP01) Expanded (CM05)
221 Tone sent to all parties on a three party conference.
(Australia Only)0
1
 
Tone is not sent.
Every 4 sec.
222 To complete the operation for setting the Call Forwarding-All 
Calls-Outside Busy Line-Outside/No Answer-Outside.0
1
 
Setting when the station goes on-hook/
when receiving Service Set Tone 
(ORT Time Out).
Setting when receiving Service Set 
Tone (ORT Time Out).
227 Whether the transferred C.O. call from a station or ATTCON 
is placed into queuing mode when all ACD/UCD stations are 
busy (effective only when CM08 – 212 is set to 1).0
1
 
The call is placed into queuing mode.
Recall to the transferring station (when 
the call is transferred from station) or 
Attendant Camp-On is set (when the 
call is transferred from ATTCON).
228 Ringing start time for wake-up call/Timed Reminder call. 0
1
 
Start at preset time.
Start at the time 5 minutes before pre-
set time. 
						

							CHAPTER 3 ND-45669 (E)
Pag e 8 0
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
232 Trunk access from a station in Room Cut-Off Status. 0
1
 
Restricted to C.O. only
Restricted to all Trunk Routes.
233 Message Waiting lamp of calling station is extinguished when 
an attendant answers (See CM13-13)0
1
 
Assigned
Not assigned
234 Whether Message Waiting/Message Reminder is reset (turn-
ing the MW Lamp off) irrespective of answering of calling 
station when the called station calls to retrieve the message.0
1
 
Available
Not available (Reset by answering of 
calling station)
235 Whether Message Waiting/Message Reminder is reset (turn-
ing the MW Lamp off) by answering at the called station 
when the calling station calls again after setting this feature.0
1
 
Available
Not available
(Depending on CM08 –234)
236 Special Dial Tone Sending for ATTCON or station dialing a 
Message Waiting access (Set/Cancel) code.0
1
 
Tone is not sent.
Tone is sent.
237 Automatic Intercom to a station set for Do Not Disturb. 0
1
 
Restricted (ROT Connection)
Intercom is available.
238 Ringing of Manual Intercom call on a station set for Do Not 
Disturb.0
1
 
No ringer on
Ringer on
239 Dial Intercom to a station set for Do Not Disturb. 0
1
 
Restricted (ROT Connection)
Intercom is available.
240 Call Forwarding-Busy Line/Split Call Forwarding-Busy 
Line/Station Hunting for a station with Do Not Disturb set.0
1
 
Allowed
Restricted (ROT Connection)
241 In a system with multiple-tenants, when a station/DID/Tie 
Line call from another tenant is terminated to a station set to 
Do Not Disturb, and when the call is transferred to a station 
by CM51 YY = 10.0
1
 
Call is routed to a station within the 
tenant of station set to Do Not Disturb.
Call is routed to a station within the 
tenant of the calling station or within 
the tenant of DID/Tie Line Trunk.
In the system with multiple-tenants and multiple-console 
operation, when a DID/Tie Line call is transferred to an 
ATTCON by CM51 YY = 00, 01, 03, 04.0
1
 
Call is routed to the ATTCON within 
the tenant of the called station.
Call is routed to the ATTCON within 
the tenant of the DID/Tie Line Trunk.
244 Terminating system of all incoming trunks is changed by 
Day/Night Mode change by station dialing.0
1
 
Available
Not available
245 Trunk Restriction class assigned by CM12 YY = 01 is 
changed by Day/Night Mode, when changed by station dial-
ing.0
1
 
Available
Not available
246 When the station (STA-A) presses the TRF key, after holding 
a conference, and makes an inquiry call with another station 
(STA-B).0
1
 
The call with STA-B is disconnected.
STA-B attends the conference (4-party 
conference).
: Initial Data
BASIC SERVICE FEATURE SETTING DATA 
						

							ND-45669  (E)   CHAPTER 3
CM 08
250  Destina ti o n o f Pr iori ty  Call  0.   0
FN C 
						

							CHAPTER 3  ND-45669  (E)
C M 08
268  Call  ter min ation t o M y L in e whi le  the  ext en sio n m ake s a  ca ll  
						

							ND-45669 (E) CHAPTER 3
Addendum-001 Page 83
AUGUST, 1998 Revision 2.1
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
311 Display last calling station number.
Note:This is only applicable for an ETJ-16DC-1, an ETJ-
16DD-1 or an ETJ-24DS-1.0
1
 
6 seconds
Until next call
319 On a Tie Line outgoing call with answer signal, transferring/
holding the call before distant called station answers. (Effec-
tive only when CM35 YY = 00 is 03 or 04 and CM35 YY = 
04 is 02.)0
1
 
Not available
Available
322 Answering method of Camp-on (Call Waiting Method). 0
1
 
Same as Camp-on transfer-method 
(SHF + Call Hold Access Code/ANS 
key)
Alternating between two calls by 
switchhook flash/ANS key.
324 Direct-In Termination-Outside
(In case of no release signal on Incoming Trunk and both an-
swer and release signals on Outgoing Trunk.)0
1Allowed
Restricted
331 Sender Prepause for the outgoing call via ATTCON 0
1To provide
Not provided
333 Mail box number sent to VMS when VMS is recalled after 
transferring the call to an unanswered station.0
1To send
Not sent
334 Call to a station, set with a Return Message Schedule Display, 
receives ringing.0
1Available (ringing)
Not Available (ROT connection)
335 Station number and name display when an incoming call be-
gins ringing in.0
1Station number and name display 
when an incoming call terminates to 
the Prime Line.
Station number and name display 
when an incoming call terminates to 
the Prime Line or Primary Extension.
352 When a call is transferred by DISA to a predetermined station 
and time-out occurs, the call is continued or dropped (CM30 
YY=30; CM41 Y=0, Function No. 39).0
1Disconnect call
Continue call
353 Buzzer sound when terminating an incoming call to an AT-
TCON that is in Attendant Console Lockout.0
1Not provided
To provide
357 Diversion display on Multiline Terminal/ATTCON when 
originating/terminating a call.0
1Available
Not available
359 When a call is transferred by an Automated Attendant to a 
predetermined station and time-out occurs, the call is contin-
ued or dropped (CM30 YY=30, 31, 32, 33; CM41 Y=0, Func-
tion No. 39).0
1Disconnect call
Continue call
361 Dial “**” is automatically added to the digits sent to the Radio 
Paging System.0
1Allowed
Restricted
INITIAL 
						

							CHAPTER 3 ND-45669 (E)
Page 84 Addendum-001
Revision 2.1 AUGUST, 1998
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
362 Confirmation tone after dialing the access code for Account 
Code/Authorization Code/Forced Account Code.0
1No tone
Service Set Tone (SST)
363 For the Automated Attendant call, caller dials while sending 
message or music.0
1Not allowed (Allowed after sending 
the message or music)
Allowed
365 Sending Dial Tone when holding a trunk by HOLD key 
(CM90 YY=00-F0058).0
1To send
Not send
366 Ringing distinction by detecting the ringing signal from the 
Main PBX (Centrex).0
1Longer Ringing than CM41 Y=2-40: 
External
Shorter Ringing than CM41 Y=2-40: 
Internal
Longer Ringing than CM41 Y=2-40: 
Internal
Shorter Ringing than CM41 Y=2-40: 
External
367 Camp-on Tone sent to a busy station by Camp-on Call Wait-
ing method.0
1Every 4 seconds
Only once
368 Central/SMDR Office feature for
Centralized Billing-CCIS.0
1To provide (for centralized office)
Not provided (for local office)
370 Call Forwarding-Outside-CCIS on incoming call from CCIS. 0
1Restrict
Allow
371 Call Forwarding Override-CCIS. 0
1Not available (BT Connection)
Available
372 Alternative Routing when the outgoing trunks of tandem of-
fice are all busy.0
1Available
Not available
373 Provide the system with Call Forwarding to the NEAX2400 
IMS VMM, when a called station is busy or not answering.0
1To provide
Not provided
374 Send ISDN CPN (BN) over CCIS to Remote PBX-First 8 dig-
its of CPN (BN) are sent.0
1Available
Not available
376 When a forwarded call is terminated to the VMS via CCIS, 
whether Message Waiting service from the VMS is provided 
for the called station.0
1To provide
Not provided
377 Sending of station number and office number of calling party 
to SMDR on tandem calls.0
1Send
Not send
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
INITIAL 
						

							ND-45669  (E)   CHAPTER 3
CM 08
378  Centr aliz ed  Billin g-CCIS fe atu re for lo ca l o ffi ce   0
IN IT IA L
IN IT IA L
FNC
IN IT IA L 
						

							CHAPTER 3 ND-45669 (E)
Pag e 8 6
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
405 Consecutive Speed Dialing when making an ISDN call. 0
1
 
Available
Not available
424 Method of charging a transferred call (for use with CP03 
(MP) only)0
1Charging to the transferring station or 
the transfer destination station.
Split charging to both the transferring 
station and transfer destination station.
425 Charging to the transfer destination station or the transferring 
station (for use with CP03 (MP) only)0
1Charging to the transferring station.
Charging to the transfer destination 
station.
Shown below are stations to which call charging is to be made in the case of various transfer patterns.
426 SMDR for incoming call if the account code is not entered 
(for use with CP03 (MP) only)
Note:When this data is assigned to 1,  SMDR for incom-
ing call is not provided even if CM13YY=05 and
CM35 YY=49 is 0 (To be provided).0
1To provide
Not provided
427 Sending additional DTMF signals when called station an-
swers, if assigning station number + additional DTMF signals 
to One-Touch key on a Multiline Terminal0
1To send
Not sent
428 VMS transfer from ATTCON, if Camp-On is set and not an-
swered0
1To provide
Not provided
430 Sending out of Calling Party Subaddress to an ISDN network 
when making a call from an ISDN Terminal0
1To send
(Depend on CM08-431)
Not sent 
431 Assignment of Calling Party Subaddress to an ISDN network 
when making a call from an ISDN Terminal0
1ISDN Circuit Station No. assigned by 
CM10
ISDN Terminal No.
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
Transfer PatternsCM08-424=1 CM08-424=0
CM08-425=1CM08-424=0
CM08-425=0
Call transfer from STA A to 
STA BSplit charging to 
STA A and STA BSTA B STA A
Call transfer from a station 
(STA) to ATTCONSTA STA STA
Call transfer from ATTCON 
to a station (STA)STA STA STA
Call transfer from ATTCON 
A to ATTCON BSplit charging to 
ATTCON A and 
ATTCON BATTCON B ATTCON A 
						

							ND-45669 (E) CHAPTER 3
Pag e 87
Revision 2.0
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
432 Forced release when a called ISDN Terminal is no answer 
during 3 minutes0
1Not available
Available
434 Assignment of the calling party number which is sent to an 
ISDN network when making a call from ISDN Terminal0
1Calling Party No. entered in ISDN 
Terminal
Calling Party No. assigned by CM12 
YY= 12/13
441 Recall display on the SN610 ATTCON. 0
1Available
Not available
442 UCD Busy Out from Sub-line 0
1Available
Not available
443 Type of Voice Mail System (VMS) 0
1VMS with MCI
VMS with PB signaling
444 Message waiting lamp control from VMS with MCI to all sta-
tions.
Note:Message Waiting lamp control is only available to
the stations in the opposite PBX connected with the
CCIS via MCI. Station dialing MW access codes
are not allowed over CCIS.0
1Available
Not available
445 Enable depressing the Paging key on SN610 ATTCON when 
the ATTCON is in idle.0
1Available
Not available
448 When the Multiline Terminal station dials “*#” during setting 
of One-Touch keys.0
1“*#” is set as dialed digit.
“*#” is set as a delimiter mark between 
dialed number and DTMF signal.
449 DID call to station with Call Forward – No Answer set over 
CCIS to a busy destination station. Destination has no call 
forwarding set.0
1Ring continuously at forwarded DID 
station
Drop to busy signal after time set by 
CM41, Y=0 function 01
450 Fault Information Storing 0
1Not performed
To perform
451 Processing at the time of the Fault Information Memory over-
flow.0
1No fault information is registered in 
case of Fault Memory overflow
Fault information is overwritten in 
case of Fault Memory overflow
460 Transfer a trunk call into an ACD group from a station or 
SN610 ATTCON.
Note:This command is used for NEAX MIS 3.XX or 4.XX
only.0
1Allowed
Not allowed
461 Sending of SMFN when answering a held call. 0
1Sent
Not sent
: Initial Data
BASIC SERVICE FEATURE SETTING DATA