NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Page 88 Addendum-001
Revision 2.1 AUGUST, 1998
CM08
COMMAND CODE
TITLE:
BASIC SERVICE FEATURES
08
Note 1:Monitoring telephone conversations may be illegal under certain circumstances and laws. Consult a legal advisor
before implementing the monitoring of telephone conversations. Some federal and state laws require a party mon-
itoring a telephone conversation to use beeptone(s), to notify all parties to the telephone conversation, and/or to
obtain consent from all parties to the telephone conversation. Some of these laws provide strict penalties for ille-
gal monitoring of telephone conversations.
Note 2:These features are required for the Hotel Printer. For detailed information, refer to the Hotel System Manual.
Note 3:CM08–262 must be made available to allow the ring test tone to be heard when using the “FNC+3” operation.
Note 4:When the ring tone 600+700 (Hz) is specified in CM15 YY=83, 84 and/or CM35 YY=34, the ring tone selection
key of Multiline Terminal is ineffective.
: Initial Data
BASIC SERVICE FEATURE SETTING DATA
462 Sending ANI/Caller ID/CPN to the OAI terminal. 0
1Available
Not available
463 Sending ANI/Caller ID/CPN to the SMDR terminal. 0
1Available
Not available
464 OAI–TSAPI
SCF1 facility0
1Same as NEAX2400 (recommended 
setting)
SMFN Off-Hook indication sent
472 Requiring ANI Signal/Caller ID from network when an in-
coming call terminates.0
1Available
Not available
474 Enhanced 911 0
1Provided
Not provided
475 Sending of Sender Tone when originating (For Enhanced 
911)0
1Sent
Not sent 
						

							ND-45669 (E) CHAPTER 3
Pag e 89
Revision 2.0
CM09
COMMAND CODE
TITLE:
ADDITIONAL SERVICE FEATURES
09
INITIAL
4. DATA TABLE:
1. FUNCTION:
This command is used to assign additional features on a system-wide basis.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
ADDITIONAL SERVICE FEATURE SETTING DATA
52MF Signaling/Enhanced 911 0
1To  p r o v i d e
Not provided
53No. 7 CCIS 0
1To  p r o v i d e
Not provided
DATA (0/1)
(2 digits) ST   + 09 +   DE   +                                  +   DE   + SERVICE
FEATURE
(2 digits) ADDITIONAL
+ EXE 
[CM09] Additional Service Features 
						

							CHAPTER 3 ND-45669 (E)
Pag e 9 0
Revision 2.0
CM10
COMMAND CODE
TITLE:
STATION NUMBER, TRUNK NUMBER, CARD NUMBER
10
MAT
1. FUNCTION:
This command is used to assign Station Numbers, Trunk Numbers, and Card Numbers to LENs (Line
Equipment Numbers).
2. PRECAUTION:
(1) When deleting a Station Number (Single Line or Multiline Terminal), be sure to delete Call Pickup
data (CM 16), UCD Group data (CM17) and Station Hunting Group data (CM18) in advance.
(2) When assigning the PN-8RSTA (PBR) card (E200–E215), the PN-CFTA card (ED00-ED03) and
the ISDN Circuit (EFX-EFxxxx), a system reset is required after setting the data.
(3) This command is included in MAT mode menu “A1” (Station Number & Class [COM01]) and
“B1” (Trunk number & data [COM01]), and “E10” [Miscellaneous Card (COM02)].
(4) Data Station Numbers are assigned by CM1A.
3. ASSIGNMENT PROCEDURE:
ST   +   10   +   DE   +   LEN   +   DE   +      TRUNK
(1- 5 digits) (4 digits)CARD STATION
DATA NUMBER +  EXENUMBER [CM10] Station Number, Trunk Number, Card Number 
						

							ND-45669 (E) CHAPTER 3
Pag e 91
Revision 2.0
CM10
COMMAND CODE
TITLE:
STATION NUMBER, TRUNK NUMBER, CARD NUMBER
10
MAT
4. DATA TABLE:
LENSETTING DATA (STATION NUMBER, TRUNK NUMBER, CARD NUMBER)
RELATED 
COMMAND
DATA MEANING OF DATA
0000
0511x
xx
xxx
xxxxSingle Line Station Number (1-4 digits) x=0-9, A (*), B (#)
Note:When assigning a 5-digits station, assign the last four digits in
CM10.
C100
C163Card number of AMP Trunk (PN-2AMPA)
When installed in PIM 0/1 . . . . .C100-C115
When installed in PIM 2/3 . . . . .C116-C131
When installed in PIM 4/5 . . . . .C132-C147
When installed in PIM 6/7 . . . . .C148-C163
(Maximum of 16 circuits per FP, 64 circuits per system.CM38
D000
D255Trunk Number (C.O./Tie Line, Paging, Radio Paging)
• For 4COT. . . 64 circuits (maximum) per PIM
• For 2COT/2ODT/AUC . . . 32 circuits (maximum) per PIM
• For TNT (BGM) . . . 10 circuits (maximum) per systemCM30
DA00
DA09Circuit Number of External Hold Tone Interface (0-9) for Music On Hold 
(PN-TNTA/PN-4COT)CM44
CM48
DB00 Card Number for Interface of an External Announcement Machine for 
Wake-Up ServiceCM44
CM48
E000
E007ATTCON Number (0-7) CM90
CM60
E100
E131DSS Console Number (00-31)
When installed in PIM 0/1 . . . . .E100-E107
When installed in PIM 2/3 . . . . .E108-E115
When installed in PIM 4/5 . . . . .E116-E123
When installed in PIM 6/7 . . . . .E124-E131
Note:The same number (the last two digits of the data) should not be
used, for both a DSS Console and Add-On Module.CM96
CM97
E200
E215Card Number of DTMF Receiver (PN-8RST A)
When installed in PIM 0/1 . . . . .E200-E203
When installed in PIM 2/3 . . . . .E204-E207
When installed in PIM 4/5 . . . . .E208-E211
When installed in PIM 6/7 . . . . .E212-E215
(Maximum of 32 DTMF Receivers [8 cards] can be assigned within a sys-
tem).CM45
Y = 0, 1
~
~
~
~
~
~
~
INITIAL 
						

							CHAPTER 3 ND-45669 (E)
Pag e 9 2
Revision 2.0
CM10
COMMAND CODE
TITLE:
STATION NUMBER, TRUNK NUMBER, CARD NUMBER
10
MAT
0124 E200
E203Circuit Number of DTMF Receiver (PN-CP03)
0000
0511E600
E663TAS Equipment Interface activated by Station Ringer.
(Use of LC card)CM30
YY = 13, 14, 17
E800
E831Card Number of External Equipment Interface (PN-DK00)
When installed in PIM 0/1 . . . . .E800-E807
When installed in PIM 2/3 . . . . .E808-E815
When installed in PIM 4/5 . . . . .E816-E823
When installed in PIM 6/7 . . . . .E824-E831CM44
E900
E963Card Number of External Key Interface (PK-DK00)
When installed in PIM 0/1 . . . . .E900-E915
When installed in PIM 2/3 . . . . .E916-E931
When installed in PIM 4/5 . . . . .E932-E947
When installed in PIM 6/7 . . . . .E948-E963CM61
EB000
EB127Circuit Number of Digital Announcement Trunk (PN-2DATA)
When installed in PIM 0/1 . . . . .EB000-EB031
When installed in PIM 2/3 . . . . .EB032-EB063
When installed in PIM 4/5 . . . . .EB064-EB095
When installed in PIM 6/7 . . . . .EB096-EB127CM30
CM49
EC00
EC31Add-On Module Number (for ETJ-24DS-1)
When installed in PIM 0/1 . . . . .EC00-EC07
When installed in PIM 2/3 . . . . .EC08-EC15
When installed in PIM 4/5 . . . . .EC16-EC23
When installed in PIM 6/7 . . . . .EC24-EC31
Note:The same number (last two digits of data) should not be used for
both a DSS Console and Add-On ModuleCM90
ED00
ED03Card Number of Conference Trunk (PN-CFTA) CM15
YY = 69
FX
FXX
FXXX
FXXXXMultiline Terminal Number
 represents Primary Extension Number
X = 0-9, A(*), B(#)
Note:The total of multiline terminal numbers and virtual station num-
bers can only equal 512, maximum.CM90
EE3XXX ZT Number (XXX = 000 – 255)
ZT Number must be assigned to the first LEN (Level 0) and/or third LEN 
(Level 2) of each LT slot.CMAD LENSETTING DATA (STATION NUMBER, TRUNK NUMBER, CARD NUMBER)
RELATED 
COMMAND
DATA MEANING OF DATA
~INITIAL
~
INITIAL 
						

							ND-45669 (E) CHAPTER 3
Pag e 93
Revision 2.0
CM10
COMMAND CODE
TITLE:
STATION NUMBER, TRUNK NUMBER, CARD NUMBER
10
MAT
0000
0511EFX
EFXXXXISDN Circuit Station Number
 represents ISDN Circuit Station Number
X : 0-9, A(*), B(#) LENSETTING DATA (STATION NUMBER, TRUNK NUMBER, CARD NUMBER)
RELATED 
COMMAND
DATA MEANING OF DATA
~INITIAL 
						

							CHAPTER 3 ND-45669 (E)
Pag e 9 4
Revision 2.0
CM10
COMMAND CODE
TITLE:
STATION NUMBER, TRUNK NUMBER, CARD NUMBER
10
MAT
• The relation between the locations of the card and the LENs (0000–0511) is shown below.
0195
0194
0193
0192
(LT00)0199
0198
0197
0196
(LT01)0203
0202
0201
0200
(LT02)0207
0206
0205
0204
(LT03)0211
0210
0209
0208
(LT04)0215
0214
0213
0212
(LT05)0219
0218
0217
0216
(LT06)0223
0222
0221
0220
(LT07)0227
0226
0225
0224
(LT08)0231
0230
0229
0228
(LT09)0235
0234
0233
0232
(LT10)0239
0238
0237
0236
(LT11)0243
0242
0241
0240
(LT12)0247
0246
0245
0244
(LT13)0251
0250
0249
0248
(LT14)0255
0254
0253
0252
(LT15)
0131
0130
0129
0128
(LT00)0135
0134
0133
0132
(LT01)0139
0138
0137
0136
(LT02)0143
0142
0141
0140
(LT03)0147
0146
0145
0144
(LT04)0151
0150
0149
0148
(LT05)0155
0154
0153
0152
(LT06)0159
0158
0157
0156
(LT07)0163
0162
0161
0160
(LT08)0167
0166
0165
0164
(LT09)0171
0170
0169
0168
(LT10)0175
0174
0173
0172
(LT11)0179
0178
0177
0176
(LT12)0183
0182
0181
0180
(LT13)0187
0186
0185
0184
(LT14)0191
0190
0189
0188
(LT15)
0067
0066
0065
0064
(LT00)0071
0070
0069
0068
(LT01)0075
0074
0073
0072
(LT02)0079
0078
0077
0076
(LT03)0083
0082
0081
0080
(LT04)0087
0086
0085
0084
(LT05)0091
0090
0089
0088
(LT06)0095
0094
0093
0092
(LT07)0099
0098
0097
0096
(LT08)0103
0102
0101
0100
(LT09)0107
0106
0105
0104
(LT10)0111
0110
0109
0108
(LT11)0115
0114
0113
0112
(LT12)0119
0118
0117
0116
(LT13)0123
0122
0121
0120
(LT14)0127
0126
0125
0124
(LT15)
0003
0002
0001
0000
(LT00)0007
0006
0005
0004
(LT01)0011
0010
0009
0008
(LT02)0015
0014
0013
0012
(LT03)0019
0018
0017
0016
(LT04)0023
0022
0021
0020
(LT05)0027
0026
0025
0024
(LT06)0031
0030
0029
0028
(LT07)0035
0034
0033
0032
(LT08)0039
0038
0037
0036
(LT09)0043
0042
0041
0040
(LT10)0047
0046
0045
0044
(LT11)0051
0050
0049
0048
(LT12)0055
0054
0053
0052
(LT13)0059
0058
0057
0056
(LT14)0063
0062
0061
0060
(LT15)
PIM 3
PIM 2
PIM 1
PIM 0PBX
0XXX
0XXX
0XXX
0XXX
(LTXX)- Level 3
- Level 2
- Level 1
- Level 0
- Card
   location
   number of
   line/trunk
   within the
   PIMs 
						

							ND-45669 (E) CHAPTER 3
Pag e 95
Revision 2.0
CM10
COMMAND CODE
TITLE:
STATION NUMBER, TRUNK NUMBER, CARD NUMBER
10
MAT
0451
0450
0449
0448
(LT00)0455
0454
0453
0452
(LT01)0459
0458
0457
0456
(LT02)0463
0462
0461
0460
(LT03)0467
0466
0465
0464
(LT04)0471
0470
0469
0468
(LT05)0475
0474
0473
0472
(LT06)0479
0478
0477
0476
(LT07)0483
0482
0481
0480
(LT08)0487
0486
0485
0484
(LT09)0491
0490
0489
0488
(LT10)0495
0494
0493
0492
(LT11)0499
0498
0497
0496
(LT12)0503
0502
0501
0500
(LT13)0507
0506
0505
0504
(LT14)0511
0510
0509
0508
(LT15)
0387
0386
0385
0384
(LT00)0391
0390
0389
0388
(LT01)0395
0394
0393
0392
(LT02)0399
0398
0397
0396
(LT03)0403
0402
0401
0400
(LT04)0407
0406
0405
0404
(LT05)0411
0410
0409
0408
(LT06)0415
0414
0413
0412
(LT07)0419
0418
0417
0416
(LT08)0423
0422
0421
0420
(LT09)0427
0426
0425
0424
(LT10)0431
0430
0429
0428
(LT11)0435
0434
0433
0432
(LT12)0439
0438
0437
0436
(LT13)0443
0442
0441
0440
(LT14)0447
0446
0445
0444
(LT15)
0323
0322
0321
0320
(LT00)0327
0326
0325
0324
(LT01)0331
0330
0329
0328
(LT02)0335
0334
0333
0332
(LT03)0339
0338
0337
0336
(LT04)0343
0342
0341
0340
(LT05)0347
0346
0345
0344
(LT06)0351
0350
0349
0348
(LT07)0355
0354
0353
0352
(LT08)0359
0358
0357
0356
(LT09)0363
0362
0361
0360
(LT10)0367
0366
0365
0364
(LT11)0371
0370
0369
0368
(LT12)0375
0374
0373
0372
(LT13)0379
0378
0377
0376
(LT14)0383
0382
0381
0380
(LT15)
0259
0258
0257
0256
(LT00)0263
0262
0261
0260
(LT01)0267
0266
0265
0264
(LT02)0271
0270
0269
0268
(LT03)0275
0274
0273
0272
(LT04)0279
0278
0277
0276
(LT05)0283
0282
0281
0280
(LT06)0287
0286
0285
0284
(LT07)0291
0290
0289
0288
(LT08)0295
0294
0293
0292
(LT09)0299
0298
0297
0296
(LT10)0303
0302
0301
0300
(LT11)0307
0306
0305
0304
(LT12)0311
0310
0309
0308
(LT13)0315
0314
0313
0312
(LT14)0319
0318
0317
0316
(LT15)
PIM 7
PIM 6
PIM 5
PIM 4PBX
0XXX
0XXX
0XXX
0XXX
(LTXX)- Level 3
- Level 2
- Level 1
- Level 0
- Card
   location
   of line/trunk
   within the 
   PIMs 
						

							CHAPTER 3  ND -4 5669 ( E)
C M 11
MAT
1.  FUNCTI ON:
STDE
+ 11   +  +
+DE
( 1–4 dig its)( 4 dig its)
~~
~
~
Autom ati c Int erc om Group No . 
AX
0 /1  to be mad e o ne pa ir 
						

							ND-45669  (E)   CHAPTER 3
CM 11
MAT
00 00
~~
~
. .  .
~
S eq uen ti a l Nu mber i n Gro up  ( 2 -7)
Man ual  In ter com Gr oup N o. 
~
~
. .  .
~
In ter com  S ta tion Number (0- 9)
Di al Int erc om  Group No .  ( 0 0-24)
~
~
. .  .
~
L oop  Num ber (1-5)
A tt e nd ant Po sit ion Number (0- 7)
~
~