NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Page 172 Addendum-001
Revision 2.1 AUGUST, 1998
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
: Initial Data
YY/YYY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
87 Distinctive Ringing by detect-
ing the ringing signal from the 
Main PBX (or Centrex).0
1 To provide
Not provided
Note 1:When this function is utilized,
be sure to set Trunk Line 
Appearance as the terminat-
ing method (CM30 YY = 02,
03, set for 02).
Note 2:Tone Ringer is selected by
CM35 YY = 34; lamp control
is set by CM35 YY = 32.CM30 
YY = 02, 03
CM30
YY = 18
89
(CRCD)Cyclic Redundancy Checking 
for DTI Trunk0
1 To provide
Not provided
90
(SPFA)Assignment of Special 
Facilities0
1
2
3
4
5
6
7 No. 7 CCIS
Not used
Basic Rate Interface
ISDN-Primary Rate Interface
Not used
PBX-PBX Interface
Not used
91
(CCH7)Assignment of Common 
Channel Handler (CCH) 
Number used for No. 7 CCIS0
3CCH 0
CCH 3CM06 
YY = 07
CMA7, A8
92
(CDTI)Assignment of Digital Data 
Transmission via DDI/No. 7 
CCIS0
1
2
3
4
5
6
7 Digital Data Transmission (48 Kbps)
Digital Data Transmission (56 Kbps)
Digital Data Transmission (64 Kbps)
Reversal of F & S Bits
Not used
Data Transmission via Modem
93
(DCHI)Assignment of D Channel 
Handler (DCH) Number00
04
15 DCH 0
DCH 4
Not usedCM06
YY=08
~~
~~
[CM35] Trunk Route Data 
						

							ND-45669 (E) CHAPTER 3
Addendum-001 Page 173
AUGUST, 1998 Revision 2.1
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
97 Assignment of route-class 
data in CCIS Route to Route 
RestrictionXX
Assignment data is the same as CM12 
YY=01
98 Designated seizure of trunks 
for Private Lines0
1 Allow
RestrictedCM12
YY=16
CM42-08
100 Assignment of Terminating 
Impedance for C.O. line00
01
02
14600 ohm (for regular/long line)
Balanced Network Imp.: complex
900 ohm
 Balanced Network Imp.: complex
600 ohm (for short line/behind PBX)
Balanced Network Imp.: 600 ohm
2-wire E&M Trunk
104 Polarity of 2-wire E&M/
4-wire E&M Trunk 
(PN-2ODT)1
2
3 E wire
M wire
Open Open
Ground Battery
Ground Ground
105 Purpose of 2-wire E&M/
4-wire E&M Trunk 
(PN-2ODT)Note 80
1 2-wire E&M Trunk
4-wire E&M Trunk
113 LAPD Mode of D channel 
Route0
1 Network mode
User mode
117 Forced disconnect of tandem 
connection for incoming trunk0
1 Allow
Not allowedCM08-029
127 Whether virtual tie line is re-
leased when there are no calls 
for predetermined time0
1 Released
Not released
129 Sending method of calling 
number from/to network0
1
3
7
 
Caller ID (CLASS)
T1-ANI
Enhanced 911
MFC-R2
: Initial Data
YY/YYY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
X X
Night Trunk Restriction class
Day Trunk Restriction class
INITIAL
AP INITIAL 
						

							CHAPTER 3 ND-45669 (E)
Page 174 Addendum-001
Revision 2.1 AUGUST, 1998
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
135 Kind of trunk route for voice 
channel and common signal-
ing channel0
1 Event Based CCIS Route
Other Trunk Route
138 Sending of received ANI
information from network to 
VMS with MCI0
1 To send
Not sent
139 Roaming Service assignment 
for Virtual COT route0
1 Available
Not availableCM30
YY=00
140 Roaming Service 0
1 Available
Not available
141 Pursuit function after roaming 
PS0
1 Provide
Not provided
142 Protocol type between PBXs 1
7Q931 a-Digital
None
143 Method for corresponding of 
virtual trunks numbers be-
tween the offices on Event 
Based CCIS0
1 By Sub-address No.
By dialed-in digits
146 Trunk ID code assigned by 
CM30 YY=19 displays on 
Multiline Terminal LCD0
1 Available
Not available (Calling/Called Sub address is 
displayed.)CM30
YY=19
: Initial Data
YY/YYY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
AP INITIAL 
						

							ND-45669 (E) CHAPTER 3
Addendum-001 Page 174-1
AUGUST, 1998 Revision 2.1
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
Note 1:In case of CM35 YY = 76, Data = 15, not specified (release the sender by time out or by answer
signal from the called distant office). 
In case of CM35 YY = 76, Data = 00 – 04, specified by the dialed digits assigned by CM85.
Note 2:STN means the calling party’s station number, and this number is sent automatically by CM30 –
28, Data = x6.
Note 3:LED indication for an internal incoming call is red (120 IPM flashing). For indicating the ter-
mination of transferred external incoming call, the flashing LED color depends on CM08-137.
Note 4:For incoming calls to a Trunk-Direct Appearance key on Multiline Terminal, the special ringing;
0.2 sec. ON – 0.2 sec. OFF is applied.
Note 5:Maximum number digit analysis should be provided to prevent one way calls (See CM35 YY =
76, CM85 and CM8A YYY = 400 – 407).
Note 6:When the Trunk Route is assigned as a C.O. line, the data for YY = 56, 57 and 58 are automati-
cally set to “Restricted”.
Note 7:When the Trunk Route is assigned as a C.O. line, the data for YY = 68 is automatically set to
“Restricted”.
Note 8:Both circuits must be set as either 2-wire or 4-wire in one PN-2ODT card; they cannot be both.
[CM35] Trunk Route Data 
						

							THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E)
Page 174-2 Addendum-001
Revision 2.1 AUGUST, 1998
This page is for your notes. 
						

							ND-45669 (E) CHAPTER 3
Pag e 1 75
Revision 2.0
CM36
COMMAND CODE
TITLE:
RESTRICTION DATA FOR TANDEM CONNECTION
36
4. DATA TABLE:
Note:The 2-digit Incoming Trunk Route number and the 2-digit Outgoing Trunk Route number are entered as a
concatenated 4-digit number. For example, the value “1824” would represent Incoming Trunk Route “18”
and Outgoing Trunk Route 24.
1. FUNCTION:
This command is used to define restriction data for tandem connection within a system, for each combi-
nation of an incoming trunk route and an outgoing trunk route.
2. PRECAUTION:
Any incoming Trunk Route assigned to “No release signal” in CM35 YY=05, is restricted from tandem
connection.
3. ASSIGNMENT PROCEDURE:
: Initial Data
INCOMING CALL 
TRUNK ROUTEOUTGOING 
TRUNK ROUTESETTING DATA
RELATED
COMMAND
DATA MEANING
00
6300
630
1 Allowed
RestrictedCM35 YY = 05
ST+36+DE+ + +DE+ +EXEINCOMING
TRUNK
ROUTE
(2 Digits)OUTGOING
TRUNK
ROUTE
(2 Digits)D ATA
(0/1)
Note
~~
[CM36] Restriction Data for Tandem Connection 
						

							CHAPTER 3 ND-45669 (E)
Pag e 1 76
Revision 2.0
CM38
COMMAND CODE
TITLE:
AMP TRUNK
38
4. DATA TABLE:
1. FUNCTION:
This command is used to define the AMP Trunk controlled data.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
YYINCOMING/OUTGOING TRUNK 
ROUTE NO.
AMP PATTERN NO.SETTING DATA
RELATED
COMMAND
DATA MEANING
00 00
14
15AMP Pattern Number 00
AMP Pattern Number 14
Not use the AMP Trunk
01 AMP Pattern Number 00
AMP Pattern Number 14Assignment of gain value
Fixed Gain
0 : 12dB
1 : 8dB
2 : 4dB
3 : 0dB
AGC(Automatic Gain Control)
0 : 0 dbr
1 : +4dbr
2 : -4dbr
3  : Through (Assigned
by Fixed Gain)
02
0
1Echo Canceller Function
Through
Normal
or AMP PATTERN NUMBER(4 digits or 2 digits) ST
INCOMING/OUTGOING TRUNK ROUTE
DE +
EXE 38YY ++
+ DATA (1-2 digits) +DE
+
Outgoing Trunk Route No.
 
Incoming Trunk Route No.
XX XX
~~ ~
X X
[CM38] AMP Trunk 
						

							ND-45669 (E) CHAPTER 3
Pag e 1 77
Revision 2.0
CM38
COMMAND CODE
TITLE:
AMP TRUNK
38
Note:CM38 YY=07 setting data 0 is effective except ISDN and CCIS lines.
03 AMP Pattern Number 00
AMP Pattern Number 140
1Echo Canceller Gain Controller
ON
OFF
04 AMP Pattern Number 00
AMP Pattern Number 140
1Mode Selection of Tone Disabler
G164
G165
05 AMP Pattern Number 00
AMP Pattern Number 140
1Detect Time of Tone Disabler
0 sec.
2 sec.
06 AMP Pattern Number 00
AMP Pattern Number 140
1Channel to be connected
Incoming Route : Tie Line
Outgoing Route : C.O. Line
Incoming Route : C.O. Line
Outgoing Route : Tie Line
07 AMP Pattern Number 00
AMP Pattern Number 140
1Timing of AMP Trunk connection
When dialing is finished Note
When answering
: Initial Data
YYINCOMING/OUTGOING TRUNK 
ROUTE NO.
AMP PATTERN NO.SETTING DATA
RELATED
COMMAND
DATA MEANING
~
~
~
~
~ 
						

							CHAPTER 3 ND-45669 (E)
Pag e 1 78
Revision 2.0
CM40
COMMAND CODE
TITLE:
FUNCTION OF RS-232C INTERFACE CIRCUIT
40
1. FUNCTION:
This command is used to assign the function of the RS-232C interface circuits, mounted on the MP card.
The MP card has two RS-232C interface circuits, which are used for the following purposes:
(1) PN-CP00/PN-CP00-B
(2) PN-CP03
(a) When using Built-in SMDR
(b) When not using Built-in SMDR
2. PRECAUTION:
None
PORT LOCATION
NUMBERPURPOSES CONNECTOR
Port 0 Local MAT D-SUB connector on the back 
wiring board (BWB).
Port 1 Remote Maintenance using external MODEM or built-
in MODEM of the MP card.RS connector on the MP card
PORT LOCATION
NUMBERPURPOSES CONNECTOR
Port 0 Built-in SMDR RS connector on the MP card
Port 1 Local MAT or Remote Maintenance using external 
MODEM or built-in MODEM of the MP card.RS connector on the MP card
PORT LOCATION
NUMBERPURPOSES CONNECTOR
Port 0 Local MAT RS connector on the MP card
Port 1 Remote Maintenance using external MODEM or built-
in MODEM of the MP card.RS connector on the MP card
[CM40] Function of RS-232C Interface Circuit 
						

							ND-45669  (E)   CHAPTER 3
CM 40
4.  DATA  T ABL E:
3.  ASSIG NM EN T P R O CEDUR E:
DATAPO RT LO CAT IO N  NU MBERD E +
40Y Y+
+ ++DE  EXE+