NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Pag e 9 8
Revision 2.0
CM11
COMMAND CODE
TITLE:
VIRTUAL-LINE NUMBER
11
MAT
Note 1:Automatic Intercom Numbers are assigned as shown below:
AUTOMATIC AUTOMATIC AUTOMATIC
INTERCOM INTERCOM INTERCOM
GROUP No.(A) No.(B)
00 A000 A100
01 A001 A101
31 A031 A131
Note 2:Manual Intercom Numbers are assigned as shown below:
MANUAL
INTERCOM
GROUP INTERCOM NUMBER
00 A200, A300, A400, A500, A600, A700
01 A201, A301, A401, A501, A601, A701
24 A224, A324, A424, A524, A624, A724
Note 3:Dial Intercom Numbers are assigned as shown below:
DIAL
INTERCOM
GROUP INTERCOM NUMBER
00 B000, B100, B200,  . . . . . .  B900
01 B001, B101, B201,  . . . . . .  B901
24 B024, B124, B224,  . . . . . .  B924
Note 4:Loop Line Numbers are assigned as shown below:
ATTENDANT
POSITION LOOP LINE NUMBER
0 AA01, AA02, AA03, AA04, AA05
1 AA11, AA12, AA13, AA14, AA15
7 AA71, AA72, AA73, AA74, AA75 
						

							ND-45669 (E) CHAPTER 3
Pag e 99
Revision 2.0
CM12
COMMAND CODE
TITLE:
STATION CLASS-1
12
MAT
1. FUNCTION:
The features for each station are determined by assigning Station Class-1 to each station number.
2. PRECAUTION:
(1) When assigning Station Class-1 to Multiline Terminal using this command, enter “X-XXXX (Pri-
mary Extension Number)” of FX-FXXXX, which is assigned by CM10, as the first data.
(2) This command is included in MAT mode menu “A1” (Station Number & Class [COM01]).
(3) The following table shows data for Single Line Station Number, Primary Extension Number of
Multiline Terminal, Virtual-Line Station Number, Data Station Number, Automatic/Manual/Dial
Intercom Number, Loop Line Number and ICI/OPR Line Number
( ) : “FAX Incoming Call Lamp Indication” onlyx : To assign
- : Not to assign
YY
STATION NUMBER00 01 02 03 04 05 07 12 13 16 17 22 23
Single line station number
(Assigned by CM10)xxxx
(x)xx
(x)-xxx---
Primary Extension number of Multiline 
Terminal (Assigned by CM10)-xxx
(x)
x-
(-)xxxxxxx
Virtual-line Station Number of Multi-
line Terminal (Assigned by CM11)-xxx
(x)
x-
(-)-xxx---
Data Station Number 
(Assigned by CM1A)-xxx
(-)
x-
(-)-xx----
Automatic Intercom Number
(Assigned by CM11)---x
(-)
--
(-)-------
Manual Intercom Number
(Assigned by CM11)--xx
(-)
--
(-)-------
Dial Intercom Number
(Assigned by CM11)--xx
(-)
--
(-)-------
Loop Line Number for Multiline Ter-
minal Attendant Position (Assigned by 
CM11)---x
(-)
--
(-)-------
ICI/OPR Line Number for Multiline 
Terminal--xx
(-)
--
(-)-------
[CM12] Station Class-1 
						

							CHAPTER 3 ND-45669 (E)
Pag e 1 00
Revision 2.0
CM12
COMMAND CODE
TITLE:
STATION CLASS-1
12
MAT
4. DATA TABLE:
3. ASSIGNMENT PROCEDURE:
: Initial Data
YY SETTING DATA
No. MEANING DATA MEANING
00
(PB/DP)DTMF or DP
(This data setting is not 
required for a Multiline 
Terminal)1
2
3DP
DTMF
DP / DTMF
01
(RSCA
RSCB)
Trunk Restriction
ClassXX 
Contents of Day/Night Trunk Restriction Class 
02
(SFCA
SFCB)Service Restriction Class 
A•BXXXX
  
Note:The features available in each class are 
programmed in CM15 YY = 00-49, YY = 53-73.
ST + 12YY + DE +
STATION
No.
(1-4 digits)Automatic/
Manual/
Dial Intercom
No. (4 digits)Loop
Line No.
(4 digits)ICI/OPR
Line No.
(4 digits)
+DE+ +EXE
DATA
(1-4 digits)
11
Day Trunk Restriction Class
XX
Night Trunk Restriction Class
1: Unrestricted (RCA)
2: Non-Restricted 1 (RCB)
3: Non-Restricted 2 (RCC)
4: Semi-Restricted 1 (RCD)
5: Semi-Restricted 2 (RCE)
6: Restricted 1 (RCF)
7: Restricted 2 (RCG)
8: Fully-Restricted (RCH)Restriction of
Connection Trunk:
CM35
YY=51-58
YY=61-68
Toll Restriction:
CM81, CM8A
1515XX
Service Restriction Class B
(00-15)
XX
Service Restriction Class A 
(00-15) 
						

							ND-45669 (E) CHAPTER 3
Addendum-002 Page 101
JANUARY, 1999 Revision 2.2
CM12
COMMAND CODE
TITLE:
STATION CLASS-1
12
MAT
: Initial Data
YY SETTING DATA
No. MEANING DATA MEANING
03
(TEL)Kind of Telephone 00
01
02
03
00
01
02
03
04
05
06
07
08
15
 
House Phone 0
House Phone 1
House Phone 2
House Phone 3
FAX Call Station Group No. 0
FAX Call Station Group No. 1
FAX Call Station Group No. 2
FAX Call Station Group No. 3
Hot Line (See CM52 YY = XX: Calling Side [0])
Automatic Intercom (See CM11, CM56 YY = 10) 
Manual Intercom (See CM11, CM56 YY = 11) 
Dial Intercom (See CM11, CM56 YY = 12) 
Multiline Terminal Attendant Position Loop Lines (See CM11)
Ordinary Station (Other than data 00-08)
04
(TENT)Tenant 00
01
 
63Tenant 00
01
Tenant 63
Note:When Tenant service is not provided, setting of this data
is not necessary. The data is automatically set to 01.
05
(LNKD)Accommodation of sin-
gle line telephone to 
Multiline Terminal
(Assignment for single 
line telephone only)0
1
 
Accommodated
Not accommodated (see CM90 YY = 00)
Note:This command setting is required when SLT LENs are
assigned to multiline keys.
Accommodation of FAX 
Call Station to Multiline 
Terminal0
1
 
Accommodated
Not accommodated
Note:When FAX Call Station No. is used for an ordinary tele-
phone, this command assignment is required. 
07
(SFCC)Service Restriction Class 
CXX
15
XX
Service Restriction Class C (00-15 )
Note:The features available in each Class are programmed in
CM15 YY = 80-98.
12
(ISUBN)Assignment of ISDN 
Subscriber’s Number/
Sending NumberX
XXXXISDN Subscriber’s Number (For calling number display 
service)/Sending number for Enhanced 911
13
(ILOCT)Local Office Code Table 
(See CM50 YY = 05)00
14
15Local Office Code Table Number 00
Local Office Code Table Number 14
Not assigned
(See CM51 YY=14)
Note 1
~~
~
~~ 
						

							CHAPTER 3 ND-45669 (E)
Page 102 Addendum-002
Revision 2.2 JANUARY, 1999
CM12
COMMAND CODE
TITLE:
STATION CLASS-1
12
MAT
Note 1:This command setting is required when Designation of FAX Station CM51 YY=14 is utilized.
Note 2:For PN-4DLCD or 4DLCA cards, this data must be assigned to first LEN (Level 0) of each 4-port DLC
card.
For PN-8DLCJ cards, this data must be assigned to first (Level 0) and fifth (Level 4) LENS of each 8-port
card.
For D
term II (4-wire DLCs), this data is not required.
Note 3:This data must be assigned in the following conditions:
• When accommodating Elite
• When accommodating Series E with Series III mode
Note 4:This assignment is only effective when CM12 YY=17 is set to Series E mode “3”.
Note 5:Assign the data as follows:
1st data: Main station (D
term Primary Extension)
2nd data: Sub station (PS)
1st data: Sub station (PS)
2nd data: Main station (D
term Primary Extension)
Note 6:As the main station number, D
term Primary Extension number must be assigned.
As the sub station number, the station number assigned to the LC that connects to the Wireless system,
must be assigned.
16
(PVTRK)Trunk to be seized as a
Private Line on a per sta-
tion basisD000
D255Trunk Number
Related Commands: CM35 YY=98, CM42-08
Combination of the main
station and sub station
for Number SharingX
XXXXMain Station Number/Sub Station Number
Note 5, Note 6
17 Kind of Multiline Termi-
nal accommodated in
DLC Card
Note 2, Note 30
1
3Series III mode
Elite mode
Series E mode
22 Multiline Terminal Soft 
KeysNote 40
1Available
Not available
23 Multiline Terminal Soft
Key Pattern Number0
1
2
3Pattern Number 0
Pattern Number 1
Pattern Number 2
Pattern Number 3: Initial Data
YY SETTING DATA
No. MEANING DATA MEANING
~
~
INITIAL 
						

							ND-45669 (E) CHAPTER 3
Pag e 1 03
Revision 2.0
CM12
COMMAND CODE
TITLE:
STATION CLASS-1
12
MAT
Note 1:Level 0 for 4DLC cards, Level 0 and Level 4 for 8DLC (8 port) cards.
Note 2:Level 1 - 3 for 4DLC (4 port) cards.
Levels 1 - 3 and 5 - 7 for 8DLC (8 port) cards.
1st LEN 
(Level 0) Note 12nd through 4th LEN 
(Level 1-3) Note 2X: Available
–: Not available
Series E (Series E mode)/Series III/E-Pro Series E (Series E mode)/Series III/E-Pro X
Series E (Series E mode/Series III mode) ATTCON/DSS Console X
ATTCON/DSS Console Series E (Series E mode)/Series III/ E-Pro/
ATTCON/DSS ConsoleX
Series E (Series III mode) Series III/E-Pro/ATTCON/DSS Console X
Elite Series E (Series E mode/Series III mode)/
Series III/E-Pro/ATTCON/DSS Console–
Series E (Series E mode/Series III mode)/Series 
III/E-Pro/ATTCON/DSS ConsoleElite – 
						

							CHAPTER 3 ND-45669 (E)
Pag e 1 04
Revision 2.0
CM13
COMMAND CODE
TITLE:
STATION CLASS-2
13
MAT
1. FUNCTION:
The features for each station are to be designated by assigning Station Class-2 for each station number.
2. PRECAUTION:
(1) When assigning Station Class-2 to a Multiline Terminal by this command, enter “X-XXXX (Pri-
mary Extension Number)” of FX-FXXXX, which is assigned by CM10, as the first data.
(2) When a station has been set as an analog data station (YY=07), the following limitations are
applied to that station:
• Periodic Time Indication tone is not given to the line.
• Override by other stations is restricted.
• Camp-on is restricted.
• Ringing interval is fixed to 1 sec. ON-2 sec. OFF.
(3) This command is included in MAT mode menu “A1” (Station number & Class [COM01]).
(4) The data for a Single Line Station Number, Primary Extension Number of a Multiline Terminal,
Virtual-Line Station Number and Data Station Number are in the following table.
´: To assign
–: Not assigned
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 21 22 28 29 32 33 34 35
Single line station number 
(Assigned by CM10)´´´´´´´´´´´–´´´´´´–´––––
Primary Extension num-
ber of Multiline Terminal 
(Assigned by CM10)
´´´´´´´´´–´–´´´´´–´´´´´´
Virtual-line Station Num-
ber of Multiline Terminal 
(Assigned by CM11)–––––
´´–––´´´´´´´––´––––
Data Station Number 
(Assigned by CM1A)–––––
´´–––––––´´––––––––
YY
STATION
NUMBER
[CM13] Station Class-2 
						

							ND-45669 (E) CHAPTER 3
Addendum-001 Page 105
AUGUST, 1998 Revision 2.1
CM13
COMMAND CODE
TITLE:
STATION CLASS-2
13
MAT
4. DATA TABLE:
3. ASSIGNMENT PROCEDURE:
: Initial Data
YY SETTING DATA
No. MEANING DATA MEANING
00
(DNDS)Do Not Disturb-System 0
1To provide
Not provided
01
(RCOF)Room Cut Off-System 0
1To provide
Not provided
02
(OFAL)Off-Hook Alarm 0
1To provide (CM51 YY = 12)
Not provided
03
(MSGW)Message Waiting Service/Message
Reminder Service0
1To provide (For station with MW lamp)
Not provided
04
(HOWLR)Howler tone automatic sending function 0
1Not provided
To provide
05
(SMDSI)SMDR/Centralized Billing-CCIS for
incoming call0
1To provided
Not provided
06
(SMDSO)SMDR/Centralized Billing-CCIS for
outgoing call0
1Not provided
To provide
07
(DL)Analog Data Station (Fax, Modem, etc.) or 
Ordinary Station0
1Data Station
Ordinary Station
08
(MRNG)To send (or not to send) a ringing signal to single 
line telephone accommodated on a multiline of 
Multiline Terminal0
1Don’t send ringing
signal
Send ringing signal
09
(PAD)Station PAD for LC 0
1Without PAD
With PAD (6 dB)
10
(VMSST)Ordinary Station or VMS Station
Note:Set to 0 for Pilot and VM station.0
1VMS Station (CM41 Y = 0, Function 
No. 44, 48, 49; CM50 YY = 00)
Ordinary Station
11
(AICM)BLF for Automatic Intercom Busy Indication 0
1To provide
Not provided
12
(SEC)Secretary Station (Boss Secretary Transfer/
Override)0
1Secretary Station
Ordinary Station or Boss Station
D ATA
(1 digit) ST   +  13YY +   DE     +                      +   DE   +                   +   EXENUMBER
(1-4 digits)STATION
See CM08 – 153
See CM35 YY = 49
See CM35 YY = 14
See CM12 YY = 05 
						

							CHAPTER 3 ND-45669 (E)
Page 106 Addendum-001
Revision 2.1 AUGUST, 1998
CM13
COMMAND CODE
TITLE:
STATION CLASS-2
13
MAT
13
(FRONT)Ordinary Station or Front Station 0
1Message Waiting Front Desk Instrument
Ordinary Station
Note:MW Lamp of calling station is
turned off when Message Wait-
ing Front Desk Terminal an-
swers (see CM08-233).
14
(HNTA)Station Hunting for incoming calls other than di-
rect-in termination calls0
1Ineffective
Effective
15
(HNTB)Station Hunting for direct-in termination calls 0
1Ineffective 
Effective
18 Reverse Signal Sending to Stations 0
1To send
Not sent
21
(VIP)VIP Class for Executive Calling (Automatic Call 
Waiting)0
1To provide
Not provided
22
(MOPN)Momentary Open
Note:Assign VMS to 0.0
1To provide (CM41 Y=1, Function No. 8)
Not provided
23 Automatic Live Record Activation 0
1Start automatically
Not available
24 Ordinary station or NEAX Mail Digital 
Station0
1NEAX Mail Digital Port
Ordinary D
term Port
25
(CLIR)Facility Control of Calling Line Identification Re-
striction (CLIR) for ISDN Call0
1To provide
Not provided
28
(OHVA)Off-Hook Voice Announcement  0
1To provide
Not provided
29
(VFAX)Designation of FAX Call Stations 0
1FAX Call Station
Ordinary Station
32 Connection of Analog Port Adapter 0
1To connect
Not connected
33 Port Mode of Analog Port Adapter 0
1Dual Port Mode
Single Port Mode
34 Designation of station connected to Dual Port 
Mode of Analog Port Adapter0
1Station connected to Dual Port Mode of 
Analog Port Adapter
Station not connected to Analog Port 
Adapter
35 To send (or not send) a ringing signal to the 
single line telephone connected to the Analog Port 
Adapter0
1Not send ringing signal
Send ringing signal
39 Roaming service for virtual LC of a Visitor PS 0
1Not send ringing signal
Send ringing signal: Initial Data
YY SETTING DATA
INITIAL
INITIAL
INITIAL 
						

							ND-45669 (E) CHAPTER 3
Pag e 1 07
Revision 2.0
CM15
COMMAND CODE
TITLE:
SERVICE RESTRICTION CLASS
15
MAT
1. FUNCTION:
The restriction of each feature is to be set for each service restriction class assigned to the stations. There
are three kinds of Service Restriction Class: A, B and C. The service features to be restricted by these
Service Restriction Classes are different.
2. PRECAUTION:
This command is included in MAT mode menu “E11” (Service Restriction [COM02]).
3. ASSIGNMENT PROCEDURE:
ST + 15YY/YYY + DE +SERVICE RESTRICTION
CLASS A/B/C
(00-15 : As assigned
in CM12 YY=02, 07)+DE++ EXEDATA
1 (digit)
[CM15] Service Restriction Class