NEC Neax2000 Ivs Command Manual

							CHAPTER 2 ND-45669 (E)
Pag e 5 4
Revision 2.0
INFORMATION FOR DATA PROGRAMMING
Single Digit Dialing 20 0 – 3 F/808 – 811
21 0 – 3 F/S
41 0 13/S Table 2-7  List of Commands for Each Hotel/Motel Feature (Continued)
For Hotel/Motel SystemF:  First Data
S :  Second Data
— :  No Data
FEATURECOMMAND
1S T DATA/2N D DATA
(F/S)REMARKS
CODE Y-YYY 
						

							ND -4 5669 ( E)  CHAPTER 2
IN FORM ATION  FO R  DATA  PR O GRAMM ING
INI TIAL
AP  INI TIAL
Syste m  F eat ure s (2)
A P  OFF  LIN E 
						

							CHAPTER 2 ND-45669 (E)
Pag e 5 6
Revision 2.0
INFORMATION FOR DATA PROGRAMMING
(2) When deleting data in any command, enter “CCC” as 2nd data.  However, data in the following commands
cannot be deleted.
• Commands where the initial data ( ) is provided but the initial data ( ) is “NONE”.
• CM29, CM41, CM42, CM60 YY = 30.
4.2 Method of Setting On-Line/Off-Line Mode
(1) For the MP card:
(a) Operation for changing on-line mode to off-line mode:
• Set SW3 to “2” or “3”.
• Press SW1.
(b) Operation for changing off-line mode to on-line mode:
• Set SW3 to “0”.
• Press SW1.
For details, refer to the Circuit Card Manual.
(2) For the AP card:
(a) Operation of changing on-line mode to off-line mode:
• Set SW1 as shown below.
SW1
OFF
4
3
2
1
ON
: POSITION TO BE SET 
						

							ND-45669 (E) CHAPTER 2
Page 57
Revision 2.0
INFORMATION FOR DATA PROGRAMMING
(b) Operation for changing off-line mode to on-line mode:
• Set SW1 as shown below.
For details, refer to the Circuit Card Manual.
4.3 Method for Installing Line/Trunk Cards
In the PBX, all line/trunk circuits are provided by installing the cards into a card shelf. The PBX employs
a flexible port assignment architecture in which the system allocates a port (Time Slot) to each LEN (Line
Equipment Number) according to system data. Consider the following conditions before installing cards:
• Number of Time Slots within Unit
• Card installation location
(1) Number of Time Slots
Figure 2-2   Line/Trunk Card Installation Location
SW1
OFF
4
3
2
1
ON
: POSITION TO BE SET
L 
T 
0 
0L 
T 
0 
1L 
T 
0 
2L 
T 
0 
3L 
T 
0 
4L 
T 
0 
5L 
T 
0 
6L 
T 
0 
7L 
T 
0 
8L 
T 
0 
9L 
T 
1 
0L 
T 
1 
1L 
T 
1 
2L 
T 
1 
3L 
T 
1 
4L 
T 
1 
5A 
P 
6M 
P 
/ 
F 
P 
/ 
A 
P 
7B 
U 
S 
/ 
A 
P 
8
P 
W 
R
BUILT-IN BATTERY
*
PIM 0 - 7
* Application cards can be mounted also in LT10 through LT15 slots. 
						

							CHAPTER 2 ND-45669 (E)
Page 58 Addendum-001
Revision 2.1 AUGUST, 1998
INFORMATION FOR DATA PROGRAMMING
• Number of ports on each card
Each card slot has four (4) LENs. For the relation between Slot Numbers and LENs, refer to the “Port
Assignment Table” of the Office Data Programming Manual.
Note:When performing the 10-party conference, two PN-CFTA cards are needed. In this case, the total num-
ber of time slots is 20.
• The following two conditions should be considered for the PBX:
Table 2-9  Port Assignment on Each Line/Trunk Card
X: Assignment possible
–: Assignment not possible
CARD NAMELEN TO BE ASSIGNED ON EACH LTXX
NUMBER OF 
CIRCUITS NUMBER OF TIME 
SLOTS
LEVEL 0 LEVEL 1 LEVEL 2 LEVEL 3
PN-4COT XXXX 4 4
PN-4LC XXXX 4 4
PN-4DLC XXXX 4 4
PN-2DLC X X – – 2 2
PN-2DATA X–X– 2 2
PN-2ODT X X – – 2 2
PN-8RSTA X–X– 8 8
PN-AUCA X X – – 2 2
PN-CFTA X – – – 8 10
PN-DK00 X – X – 8 0
PN-TNTA X – X – 2 4
PN-2DPCB X–X– 2 2
PN-2AMPA X–X– 2 4
PN-2ILCA X X – – 2 5
Number of time slots within any PIMs (0 - 7)   £ 64 time slots
Number of time slots per System  £ 512 time slots 
						

							ND -4 5669 ( E)  CHAPTER 2
IN FORM ATION  FO R  DATA  PR O GRAMM ING
 +   03  +   +  Pa ssword  L ev el  N o. +  +   P asswo rd  + STDEDEEXE
 +   03  +   +  9 +   +   CC CC CCC C + STDEDEEXE
8 dig its 
						

							CHAPTER 2 ND-45669 (E)
Pag e 6 0
Revision 2.0
This page is for your notes. 
						

							ND-45669 (E) CHAPTER 3
Page 61
Revision 2.0
DESCRIPTION OF COMMANDS
CHAPTER 3 DESCRIPTION OF COMMANDS
1. GENERAL
This chapter provides a detailed description for each command.
2. DETAILED DESCRIPTION OF COMMANDS
This section describes the methods for programming commands. Information about each command is present-
ed in the following order:
(1) Function:
The function of the command.
(2) Precaution:
Precautions related to assigning data.
(3) Assignment Procedure:
The procedure for assigning data.
(4) Data Table:
A detailed description of the data.
In the description of each command, initial data which is automatically loaded into memory, after system ini-
tialization (using position “B” on SW3 of the MP, followed by a reset) is indicated with “   ”.  Refer to Chap-
ter 4 for details on default data when the automatic resident program function (using position “C” on SW3 of
the MP, followed by a reset) is used.
The installer should confirm the meaning of initial data, and change or delete the data, if required. If under the
command code designation there is an   abbreviation, then programming can be accomplished by the
MAT mode of programming instead of the MOC mode or CAT mode.
MAT 
						

							CHAPTER 3 ND-45669 (E)
Page 62 Addendum-002
Revision 2.2 JANUARY, 1999
CM00
COMMAND CODE
TITLE:
SYSTEM DATA MEMORY ALL CLEAR
00
[CM00] System Data Memory All Clear
4. DATA TABLE:
1. FUNCTION:
This command confirms that the system data memory (RAM) area can be Written-in /Read-out and also
assigns the Initial Data to the RAM area.
2. PRECAUTION:
(1) This command can only be used in off-line mode.
(2) When this command is executed, “OK” displays with Memory Clear completed (about 30 seconds
later).
(3) If an error exists in memory, “WD ERROR” displays.
(4) This command is not available with a CAT. To clear all system data, set SW3 to “B”, and press SW1
on the MP card. In this case, the only functional port is LEN0000, which is assigned as a CAT.
3. ASSIGNMENT PROCEDURE:
1ST DATA 2ND DATA
DATA MEANING DATA MEANING
1 System data memory all clear CCC Clear
3 System data clear for new memory area
Note:This data is available when using
PN-CP00-C/CP02-C/CP03-C card.CCC Clear
+00+ +
++ +CCC MEMORY AREA
EXESTDEDE
DESIGNATION
(1/3) 
						

							ND-45669 (E) CHAPTER 3
Pag e 63
Revision 2.0
CM01
COMMAND CODE
TITLE:
SYSTEM DATA MEMORY PARTIAL CLEAR
01
4. DATA TABLE:
1. FUNCTION:
This command is used to clear the data associated with the Numbering Plan (CM20-CM29) or Toll
Restriction (CM85-CM8A).
2. PRECAUTION:
This command can only be used in off-line mode.
3. ASSIGNMENT PROCEDURE:
CLEAR
DESIGNATIONSYSTEM DATA TO BE CLEARED REMARKS
20 CM20: Assignment of Numbering Plan
CM21: Assignment of Single Digit Access Code
CM22: Assignment of Route Advance
CM23: Assignment of Tenant Development
CM24: Assignment of Kind of Calling Terminal Development
CM25: Assignment of Kind of Special Terminal Development
CM26: Assignment of Closed Number
CM29: Assignment of Numbering Plan Tenant Group
80 CM85: Assignment of Maximum Number of Digits on C.O. Call
CM88: Assignment of Dialed Digit requiring an automatic pause
CM8A: Assignment of LCR/Toll Restriction Development Table
740 Clears Guest Name memory area
+01+ + + + +CCC 80 Commands to be cleared: 20, 21, 22, 23, 24, 25, 26 and 29 in Data Memory
Commands to be cleared: 85, 88 and 8A in Data MemoryEXESTDEDE +01+ + + + +CCC 20EXE
STDEDE
+01+ + + + +CCC 740EXE
STDEDE
[CM01] System Data Memory Partial Clear