NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Page 216 Addendum-002
Revision 2.2 JANUARY, 1999
CM49
COMMAND CODE
TITLE:
DIGITAL ANNOUNCEMENT TRUNK
49
YY DIGITAL 
ANNOUNCEMENT 
TRUNK CIRCUIT/
TENANT No.SENDING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
01 Message No. of 
1st Answering 
Message of 
Automated 
AttendantXX:  Tenant Number
(00 – 63)XX Message Number (00 – 63)
assigned by CM49 YY=00
02 Message No. of 
2nd Answer-
ing Message/
Night Message 
of Automated 
Attendant
05 Message No. of 
Hold ServiceCM48 Y=0
06 Message No. of 
Transferred 
Trunk Line
(No Answer) Tenant Number of 
transferring station 
should be set.CM65 YY=50
07 Message No. of 
Transferred 
Trunk Line 
(Busy)CM65 YY=51
08 Message No. of 
Automatic 
Wake-Up/
Timed 
ReminderCM48 Y=1
10 Message 
Group No. of 
Announce-
ment Service 
for WCSXX Message Group No. (00 – 63)
assigned by CM49 YY=00
12 Message-
Group No. of 
Announce-
ment Service -
PS Out of Cell/
PS Power Off 
						

							ND-45669 (E) CHAPTER 3
Addendum-001 Page 216-1
AUGUST, 1998 Revision 2.1
CM49
COMMAND CODE
TITLE:
DIGITAL ANNOUNCEMENT TRUNK
49
YY DIGITAL 
ANNOUNCEMENT 
TRUNK CIRCUIT/
TENANT No.SENDING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
13 Message No. of 
Vo i c e  G u i d e00: When message 
waiting is set
01: When service is set
02: When service is 
cancelled
03: When Call For-
warding-All Calls/
Do Not Disturb is 
setXX Message Number (00 – 63)
assigned by CM49 YY=00CM48 Y=2
CM49 YY=00-
17XX
0A Message No. of 
Attendant
Delay
AnnouncementXX:  Tenant Number
(00 – 63) 
						

							THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E)
Page 216-2 Addendum-001
Revision 2.1 AUGUST, 1998
This page is for your notes. 
						

							ND-45669 (E) CHAPTER 3
Addendum-001 Page 217
AUGUST, 1998 Revision 2.1
CM50
COMMAND CODE
TITLE:
COMMON ROUTE INDIAL
50
1. FUNCTION:
This command is used to assign LDNs (Listed Directory Numbers) to DID or Tie lines. When these
numbers are dialed into the system, either on an incoming tie line or an incoming C.O. line set up for
indialing, the call will appear at a specified call identification key on the attendant’s console.
The system allows digits to be added to or deleted from indialed numbers on a route basis. This
command, in conjunction with CM35 YY=17, allows two extra leading digits to be specified.
The common route indial facility allows up to eight LDNs to be identified. In addition, this command is
used to assign the access code to be sent to a Voice Message System (VMS) before/after a Mail Box
Number.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
ST + 50YY + DE + + DE + + EXEKIND OF DATA
(1 - 3 digits)DATA
(1 - 12 digits)
[CM50] Common Route Indial 
						

							CHAPTER 3 ND-45669 (E)
Page 218 Addendum-001
Revision 2.1 AUGUST, 1998
CM50
COMMAND CODE
TITLE:
COMMON ROUTE INDIAL
50
4 . D ATA  TA B L E :
Note 1:CM35 YY = 17 allows digits to be added or deleted from indialed digit streams on a route basis.
Note 2:“C” or “D” should not be assigned as the first characters of an access code to insert a prepause
timing. The prepause timing should be assigned with CM41 YY=0 Function No. 44.
Note 3:If “C” is inserted in the access code, it can be used as a pause (1.5 sec). To provide a program-
mable pause, insert “D” instead of “C”. (Programmable pause; CM41 Y=0, Function No.38)
Note 4:Data set by this command is overridden by data set in CM58.
Note 5:These numbers should be different from any number assigned by CM10 and CM11.
: Initial Data
YYKIND OF DATA SETTING DATA
CODE MEANING DATA MEANING
00 0 Two leading digits to be added
Note 1XX Digits to be added
3 Access Code to be sent out before a Mail Box Number
Note 2XX
XXXX
NONE Access Code to be sent out 
to a VMS
X: 0 – 9, A (*), B (#), C/D 
(Pause)
Note 3
Not to be sent out 4 Access Code to be sent out after a Mail Box Number
5 Primary digit of 5 digits station X
01 0
1
8Effective data in CM35 YY = 15
LDN 0 ATTCON key (Data 00 in CM90)
LDN 7 key (Data 07 in CM90)
Note 4XX
XXXXDialed number
Note 5
02 0
1
8Effective data in CM35 YY = 15
TIE 0 key (Data 40 in CM90)
TIE 7 key (Data 47 in CM90)
Note 4XX
XXXXDialed number
Note 5
05 00
14Local Office Code Table Nro. 00
Local Office Code Table No. 14X . . . . .X
(Max. 12 
digits)Local office code
~
~~~
~
~~~
~
~~ 
						

							ND-45669 (E) CHAPTER 3
Pag e 2 19
Revision 2.0
CM51
COMMAND CODE
TITLE:
AUTOMATIC TRANSFER DESTINATIONS
51
4. DATA TABLE:
1. FUNCTION:
This command is used to define destinations for different types of diversion.
2. PRECAUTION:
If a transferred station number for a house phone call and a transferred station number for off-hook
alarm are the same, this service is not effective.
3. ASSIGNMENT PROCEDURE:
YYGROUP NUMBER SETTING DATA
No. MEANING DATA MEANING
00 00
63Tenant 00
Tenant 63For DID line, transfer destination of incoming 
call when the station does not answer the call 
within a predetermined time.
X
XXXX
or
E000
or
EBXXXWhen a station is  des-
ignated as the destina-
tion, the setting data is 
as follows: 
X – XXXX
When an ATTCON is 
designated as the des-
tination, the setting 
data is as follows: 
E000
In case a Digital An-
nouncement Trunk is 
designated as the des-
tination in YY = 00, 
01, 03, 04, 06, 07, 08, 
set the data to 
“EBXXX 
(000 – 127)”. 01 00
63Tenant 00
Tenant 63For Tie line, transfer destination of incoming call 
when the station does not answer the call within 
a predetermined time.
03 00
63Tenant 00
Tenant 63For DID line, transfer destination of incoming 
call when the station is busy.
04 00
63Tenant 00
Tenant 63For Tie line, transfer destination of incoming call 
when the station is busy.
06 00
63Tenant 00
Tenant 63For DID line, transfer destination of incoming 
call when the station number is not assigned. 
(When CM 08-032 is 1)
07 00
63Tenant 00
Tenant 63For Tie line, transfer destination of incoming call 
when the station number is not assigned. (When 
CM 08-032 is 1) (See CM49 YY=00, 06, 07)
08 00
63Tenant 00
Tenant 63For station-to-station call, transfer destination of 
the call when the station number is not assigned.E000
or
EBXXX
GROUP
ST + 51YY + DE + NUMBER + DE + + EXE
(2 digits)DATA
(1 - 4 digits
~~
~~~
~~
~~
~~
~~
~~
[CM51] Automatic Transfer Destinations 
						

							CHAPTER 3 ND-45669 (E)
Pag e 2 20
Revision 2.0
CM51
COMMAND CODE
TITLE:
AUTOMATIC TRANSFER DESTINATIONS
51
10 00
63Tenant 00
Tenant 63Transfer destination of the call when the called 
station is set to Do Not Disturb.X
XXXXStation Number as the 
destination of a call 
diversion. 
In case ATT is desig-
nated as the destina-
tion, the setting data is 
as follows: 
ATT=E 000 (Fixed) 11 00
63Tenant 00
Tenant 63Transfer destination of the call when the Room 
Cut Off station dials C.O. access code.
12 00
63Tenant 00
Tenant 63Destination of Off Hook Alarm/Priority Call 0/1. 
(See CM08-250, 251, CM13 YY=02, CM15 
YY=17, 18)
13 00
01
02
03ATT Group 0
ATT Group 1
ATT Group 2
ATT Group 3Transfer destination of the call when a station 
dials the operator access code of ATTCON in 
night mode
(See CM60 YY=00)
14 00
01
02
03House Phone 
Group 0
House Phone 
Group 1
House Phone 
Group 2
House Phone 
Group 3Destination of the House Phone 
(See CM12 YY=03)
00
01
02
03FAX Call 
Station 
Group 0
FAX Call 
Station 
Group 1
FAX Call 
Station 
Group 2
FAX Call 
Station 
Group 3Designation of the Fax Stations
(Designation of House Phone called Side)
(See CM12 YY=03)X
XXXXFAX Call Station No.
15 00
63Tenant 00
Tenant 63Destination of the call from the station to which 
Message Waiting has been set. 
(See CM13 YY=13)X
XXXX
17 00
63Tenant 00
Tenant 63Destination of the call after the first time 
interval of the ACD/UCD Delay 
Announcement.X
XXXX YYGROUP NUMBER SETTING DATA
No. MEANING DATA MEANING
~~~
~~
~~
~
~~~
~~~ 
						

							ND-45669 (E) CHAPTER 3
Addendum-001 Page 221
AUGUST, 1998 Revision 2.1
CM51
COMMAND CODE
TITLE:
AUTOMATIC TRANSFER DESTINATIONS
51
YYGROUP NUMBER SETTING DATA
No. MEANING DATA MEANING
18 00
63Tenant 00
Tenant 63Destination VMS of a call that is set Camp-On 
and not answered/Destination VMS of Call Re-
direct.X
XXXXVMS Station No.
20 00
63Tenant 00
Tenant 63Destination VMS station for Call Forwarding-
Not AvailableX
XXXXVMS Station No.
21 00
63Tenant 00
Tenant 63Destination of Alternate Hold Recall for 
Enhanced Trunk Direct AppearanceX
XXXXStation No. Only
22 00
63Tenant 00
Tenant 63Destination station of Call Redirect X
XXXXStation No. Only
~~~
~~~
~~~
~~~ 
						

							CHAPTER 3 ND-45669 (E)
Pag e 2 22
Revision 2.0
CM52
COMMAND CODE
TITLE:
HOT LINE
52
MAT
1. FUNCTION:
This command is used to assign a Hot Line to stations, ATTCONs and trunks.
2. PRECAUTION:
(1) The maximum number of Hot Lines is 100, and the connection is one way from the calling side to
the called side. Thus, for connection in the opposite direction, the calling and called side must be
assigned to another Hot Line number. If all the Hot Lines are to be made bothway lines, the maxi-
mum number of Hot Lines is 50.
(2) The Station Number to be assigned as the Calling Station Number must be set as “Hot Line” via
CM12 YY = 03.
(3) If Hot Line-Outside is assigned by this command, data assignment via CM71 and CM72 are
required.
(4) This command is included in MAT mode menu “A6” (Hot Line [COM01]).
3. ASSIGNMENT PROCEDURE:
CALLING SIDE/
ST + 52YY + DE + CALLED SIDE + DE + + EXE
(1 digit)DATA
(1 - 4 digits)
[CM52] Hot Line 
						

							ND-45669 (E) CHAPTER 3
Pag e 2 23
Revision 2.0
CM52
COMMAND CODE
TITLE:
HOT LINE
52
MAT
4. DATA TABLE:
4.1 Hot Line
4.2 FAX Incoming Call Lamp Indication
YY
CALLING/CALLEDSETTING DATA
No. MEANING DATA MEANING
00
99Hot Line Num-
ber 00 ~ 990 Calling Side X
XXXXStation Number/Data Station Number
(See CM12 YY = 03)
1 Called Side X
XXXXStation Number/Data Station Number
E000 ATTCON
01XX Hotline-Outside
XX represents the abbreviated code for System 
Speed Dialing (See CM71 and CM72)
YY
CALLING/CALLEDSETTING DATA
No. MEANING DATA MEANING
00
99Pair Number
00 - 990 Calling Side X
XXXXFAX Call Station No.
(Hot Line Station No.)
1 Called Side X
XXXXFAX Station No.
(Hot Line Station No.)
~~
~
~~
~