NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Pag e 1 54
Revision 2.0
CM30
COMMAND CODE
TITLE:
TRUNK DATA
30
MAT
04
(DDIT)Direct–In Termination in Day 
ModeX
XXXXStation Number for Direct–In Termi-
nation in Day ModeCM10, 11
CXX Abbreviated Code of System Speed 
Dialing for DIT–Outside (XX=00–31)CM71–66
CM35 YY=40
EBXXX Digital Announcement Trunk Circuit 
Number
(XXX=000–127)CM10, CM15
YY=33 CM20–
A00, A01, A02
CM49 YY=03000
05
(NDIT)Direct–In Termination in Night 
ModeX
XXXXStation Number for Direct–In Termi-
nation in Night Mode: Night Connec-
tion–FixedCM10, 11
CM08–179
CXX Abbreviated Code of System Speed 
Dialing for DIT–Outside
(XX=00–31)CM71–66
CM35 YY=40
EBXXX Digital Announcement Trunk Circuit 
Number
(XXX=000–127)CM10, CM15
YY=33 CM20–
A00, A01, A02
CM49 YY=03000
07
(IPRA)Assignment of CIC (Circuit 
Identification Code) used for 
ISDN–Primary Rate Access000
029CIC 000
CIC 029CM07 YY = 01
08
(NTMB)Restriction of outgoing connec-
tion during night mode0
1 Restricted
AllowedCM60
CM61
09
(TRKG)Trunk Group Number 
Note:Paging Trunks can-
not be assigned to the
Trunk Group Busy
Lamp.01
6201–62 Identification of Trunk Group 
Busy Lamps on an external 
display device (CM44) or on 
the Multiline Terminal/AT-
TCON (CM90)CM44–11XX
CM90–F1201–
F1262
: Initial Data
YY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
~
~
~~
~ 
						

							ND -4 5669 ( E)  CHAPTER 3
CM 30
MAT
: In it ia l D ata
~
~
~~
~~
~ 
						

							CHAPTER 3 ND-45669 (E)
Page 156 Addendum-002
Revision 2.2 JANUARY, 1999
CM30
COMMAND CODE
TITLE:
TRUNK DATA
30
MAT
: Initial Data
YY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
28
(PAGA)Paging Answer Zone/Kind of 
PagingXX
CM20 – 070
CM20 – 079
CM44 – 02XX
Paging Answer Zone
0: Paging Answer Zone 0
9: Paging Answer Zone 9
Kind of Paging
0: Speaker Paging, no answer
1: Radio Paging, no answer
2: Speaker Paging, non-delay answer
3: Radio Paging, non-delay answer
4: Speaker Paging, non-delay and de-
lay answer
5: Radio Paging, non-delay and delay 
answer
6: Radio Paging, no answer and call-
ing party’s station number is sent 
automatically 
CM35 YY=08
CM35 YY=08, 13
30
(DRAD)Handling of busy/not available 
Automated Attendant/Direct 
Inward System Access (DISA) 
destination in Day mode.
Note:For DISA, this data is
effective only for a
station call.00
01
02
03
04
05
06
07
08
15 Disconnection
Forward to TAS Indicator
Forward to ATTCON
Forward to DIT Station
Music and DT Connection (Redial)
DT Connection (Redial)
Automated Attendant: Announcement 
and DT Connection (Redial) or DISA:
Disconnection 
Note:When providing a night mes-
sage for automated attendant, the
2nd answering message, which is
assigned by CM49 YY=00 2nd
data 02XX, is used for the night
message. In that case, the 2nd
data 08 of CM30 YY=30, 31 can-
not be specified for handling of
busy/not available automated at-
tendant destination.
DisconnectionCM41 
(Y=0 No. 34)
CM45
CM30
YY=04, 05
CM49
YY=02,
CM48 Y=2
X
Kind of Paging X
Paging Answer Zone
~ 
						

							ND-45669 (E) CHAPTER 3
Addendum-002 Page 156-1
JANUARY, 1999 Revision 2.2
CM30
COMMAND CODE
TITLE:
TRUNK DATA
30
MAT
: Initial Data
YY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
31
(NRAD)Handling of busy/not available/
Automated Attendant/ Direct 
Inward System Access (DISA) 
in night mode.
Note:For DISA, this data is
effective only for a
station call.00
15 Same as YY=30 CM41
(Y=0 No. 34)
CM45
~ 
						

							THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E)
Page 156-2 Addendum-002
Revision 2.2 JANUARY, 1999
This page is for your notes. 
						

							ND-45669 (E) CHAPTER 3
Pag e 1 57
Revision 2.0
CM30
COMMAND CODE
TITLE:
TRUNK DATA
30
MAT
Note 1:When data 02, 03, 11 or 20 is assigned, the data for YY=18 should be set to 0.
Note 2:For DIDs and Tie Lines, YY = 02 and YY = 03 should be set to 31.
Note 3:For individual trunk access, it is necessary to assign the Trunk ID code in YY=19. The codes assigned
are the Trunk ID codes to be displayed on the ATTCON or Multiline Terminal.
32
(RATO)Handling of timed–out
Automated Attendant Call in 
Day mode.00
01
02
03
04
06
07
15 Disconnection
Forward to TAS Indicator
Forward to ATTCON
Forward to DIT Station
DT Connection (Redial)
DisconnectionCM41 Y=0
Function
No. 43
CM45
CM30
YY=04, 05
CM48 Y=2
33
(RAB)When YY=30, 31 is set to data 
08, if all DTMF Receivers are 
busy.00
01
02
03
04
07
15 Disconnection
Forward to TAS Indicator
Forward to ATTCON
DisconnectionCM45
34
(ILOC)Assignment of ISDN local
Office Code Table Number00
14
15 Local Office Table No. 00
Local Office Code Table No. 14
Not AssignedCM50 YY=05
35
(CIC7)Assignment of CIC (Circuit 
Identification Code) used for 
No.7 CCIS001
127CIC 001
CIC 127CM30 YY=02, 03
37 Handling of timed–out
Automated Attendant Call in 
Night mode00
01
02
03
04
06
07
15 Disconnection
Forward to TAS Indicator
Forward to ATTCON
Forward to DIT Station
DT Connection (Redial)
DisconnectionCM41 Y=0
Function No. 43
CM45
CM30
YY=04, 05
CM48 Y=2
: Initial Data
YY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
~~
~~ 
						

							CHAPTER 3 ND-45669 (E)
Pag e 1 58
Revision 2.0
CM31
COMMAND CODE
TITLE:
SYSTEM ATTRIBUTE DATA
31
MAT
4. DATA TABLE:
1. FUNCTION:
This command is used to assign the system attribute data.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
Y1S T DATA 2ND DATA
DATA MEANING DATA MEANING
1 0 MF PAD Control to incoming signal 0
1
2
3
4
7–8 dBm
–10 dBm
–11.5 dBm
–9.13 dBm
Not used
1 Sensitivity Level of MF Receiver 00
14
15–21 dBm
–35 dBm
–36 dBm
(–1 dBm increments)
2 Number of received digits of called number 
from T1 networkNONE
01
31None
1 digit
31 digits
3 Number of received digits of ANI Signal/Caller 
ID from networkNONE
01
31None
1 digit
31 digits
STDE +31Y + ++DE
(1-2 digits)  2ND DATA
++EXE(1-2 digits)  1ST DATA
~
INITIAL~~
INITIAL~
~
INITIAL~
~
[CM31] System Attribute Data 
						

							ND-45669  (E)   CHAPTER 3
CM 31
MAT
20
 R ECE IV ER
0  No. 0 –3  as S ender
~
~~
I N IT IA L
~
~
I N IT IA L~
~ 
						

							CHAPTER 3 ND-45669 (E)
Page 160 Addendum-002
Revision 2.2 JANUARY, 1999
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
1. FUNCTION:
This command assigns trunk route characteristics. A trunk route is a group of trunks with common char-
acteristics used for a common purpose.
2. PRECAUTION:
(1) The following table shows the value of the Central Office Trunk (COT/DID) PAD or Tie Line
Trunk (ODT/DTI) PAD assigned by YY=19, Data 4 – 7. (T:Transmitter PAD [dB], R:Receiver PAD
[dB])
+: Gain
-: Loss
CONNECTION PATTERNS (A–B)PAD DATA OF B TRUNK
DATA=4
(T/R)DATA=5
(T/R)DATA= 6
(T/R)DATA =7
(T/R)
Station-ODT (4W E&M) -3/-3 -3/-3
Tone-ODT (4W E&M) 0/0 0/0
COT/DID-ODT (4W E&M) -2/-2 0/0
ODT (4W E&M)-ODT (4W E&M) 0/0 0/0
DTI-ODT (4W E&M) 0/0 0/0
Station-COT/DID/ODT (2W E&M) 0/+6 0/+6
Tone-COT/DID/ODT (2W E&M) 0/0 0/0
COT/DID-COT/DID/ODT(2W E&M) 0/0 0/0
ODT (4W E&M)-COT/DID/ODT (2W 
E&M)0/0 0/0
DTI-COT/DID/ODT (2W E&M) 0/0 0/0
Station-DTI -3/-8 -3/-3 -3/-3 -3/-8
Tone-DTI 0/0 0/0 0/0 0/0
COT/DID/ODT (2W E&M)-DTI 0/0 0/0 0/0 0/0
ODT (4W E&M)-DTI  +3/-3 0/0 0/0 +3/-3
DTI-DTI 0/-6 0/0 0/-6 0/0 
						

							ND-45669 (E) CHAPTER 3
Pag e 1 61
Revision 2.0
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
(2) When assigning a Tie Line, the data in YY = 09 (Incoming Call Signaling System) should be simi-
lar to that of YY = 20 (Sender Starting Condition). The following table shows the assignment of the
Sender Starting Condition in relation to the Incoming Call Signaling System.
Note:( ) indicates the data to be assigned.
(3) This command is included in MAT mode menu “B2” (Trunk Route data [COM01]).
3. ASSIGNMENT PROCEDURE:
INCOMING CALL 
SIGNALING SYSTEM (YY = 09)SENDER STARTING CONDITION 
(YY = 20); ( ) = data to be assignedREMARKS
Ground Start (01) Ground Start (02)
Loop Start (15) Loop Start (15)
Wi n k St art  (0 3) Wi n k St art (0 0)
Delay Dial (04) Delay Dial (01)
Immediate (05) Timing Start (15)
2nd DT/Timing (06) Timing Start (15)
ST + 35YY/YYY + DE + + DE + + EXETRUNK ROUTE
(2 digits)DATA
(1-4 digits)