NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Pag e 2 24
Revision 2.0
CM53
COMMAND CODE
TITLE:
TRUNK ANSWER FROM ANY STATION RESTRICTION
53
4. DATA TABLE:
1. FUNCTION:
This command is used to define the conditions for TAS service.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
Y CONDITION SETTING DATA
No. MEANING CODE MEANING DATA MEANING
0
1
2
3
4TAS Answer A
(CM20-047)
TAS Answer B
(CM20-048)
TAS Answer C
(CM20-049)
TAS Answer D
(CM20-050)
TAS Answer E
(CM20-051)0 Answering a C.O. Ringdown 
Incoming Call (CM30 YY = 02, 03)0
1 Not allowed
Allowed
1 Answering a DID/Tie Line Incoming 
Call (CM76, data = D13, CM58 YY = 
02 - 07)0
1 Not allowed
Allowed
3 Answering a C.O. Incoming Call 
(Night) in the case of Day/Night 
Changeover System (CM30 YY = 03)0
1 Not allowed
Allowed
4 Answering an overflow call of Direct-
In Termination (CM30 YY = 13, 14)0
1 Not allowed
Allowed
7 Own and Other Tenant Answer, or
Own Tenant Answer0
1 Own and Other 
Tenant Answer 
(Related to CM63)
Own Tenant Answer
CONDITION
ST + 53Y + DE + CODE + DE + + EXE
(1 digit)D ATA
(1 digit)
[CM53] Trunk Answer From Any Station Restriction 
						

							ND-45669 (E) CHAPTER 3
Pag e 2 25
Revision 2.0
CM56
COMMAND CODE
TITLE:
INTERCOM ZONE PAGING GROUP/INTERCOM GROUP
56
MAT
4. DATA TABLE:
1. FUNCTION:
This command is used to assign the Multiline Terminal station number for Automatic/Manual/Dial
Intercom and Internal Zone Paging.
2. PRECAUTION:
This command is included in MAT mode menu “A8” (Intercom Group [COM01]).
3. ASSIGNMENT PROCEDURE:
: Initial Data
YY INTERCOM
No.
SERIAL No.SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
00
07Internal Zone 
Paging Group 0
Internal Zone 
Paging Group 7XX: Serial Num-
ber within the 
group 
(00 - 15)X
XXXXPaged Station Number
(Primary Extension Number 
of the Multiline Terminal to 
be set)CM15 YY = 49
CM20-A30-A45
CM90
00
07Simultaneous 
Paging Group 0
Simultaneous 
Paging Group 7XX: Serial Num-
ber within the 
group 
(00 - 15)X
XXXXStation Number
(Primary Extension Number 
of the Multiline Terminal to 
be set)CM15 YYY = 119
CM20 B00-B17
CM90
10 Assignment of 
Automatic Inter-
com NumberA000
A100,
A001
A101,
A031
A131X
XXXXStation Number
(Primary Extension Number 
of the Multiline Terminal to 
be set)CM11
CM12 YY = 03
CM90
CM08-237
ST + 56YY + DE + + DE + + EXESERIAL No. INTERCOM No.
(2 digits) (4 digits)DATA
(1 - 4 digits)
~
~
~
~
~
~
. . .
~
[CM56] Intercom Zone Paging Group/Intercom Group 
						

							CHAPTER 3 ND-45669 (E)
Pag e 2 26
Revision 2.0
CM56
COMMAND CODE
TITLE:
INTERCOM ZONE PAGING GROUP/INTERCOM GROUP
56
MAT
11 Assignment of 
Manual Intercom 
NumberA200
A700
A201
A701
A224
A724X
XXXXStation Number
(Primary Extension Number 
of the Multiline Terminal to 
be set)CM11
CM12 YY = 03
CM90
CM08-238
12 Assignment of Dial 
Intercom NumberB000
B900
B001
B901
B024
B924X
XXXXStation Number
(Primary Extension Number 
of the Multiline Terminal to 
be set)CM11
CM12 
CM90
CM08-239
: Initial Data
YY INTERCOM
No.
SERIAL No.SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
~
~
. . .
~
~
~
~
. . .
~
~ 
						

							ND-45669 (E) CHAPTER 3
Pag e 2 27
Revision 2.0
CM58
COMMAND CODE
TITLE:
LDN DIVERSION
58
4. DATA TABLE:
Note:Data set by this command is effective based on the data assigned by CM50 YY = 01/02.
1. FUNCTION:
This command is used to assign information to each DID or TIE trunk for which incoming calls are to be
redirected to an alternative destination.
2. PRECAUTION:
This data is valid when CM08-205 is assigned to “0”.
3. ASSIGNMENT PROCEDURE:
LDN/TIE
NoteMEANING
00
01
08Effective data in CM35 YY = 15
LDN 0 Key (Data 00 in CM90)
LDN 7 Key (Data 07 in CM90)
10
11
18Effective data in CM35 YY = 15
TIE 0 Key (Data 00 in CM90)
TIE 7 Key (Data 07 in CM90)
ST + 58YY + DE + + DE  + + EXELDN/TIE
(2 digits)D ATA
(1 - 4 digits)
~~
~~
[CM58] LDN Diversion 
						

							CHAPTER 3 ND-45669 (E)
Pag e 2 28
Revision 2.0
CM58
COMMAND CODE
TITLE:
LDN DIVERSION
58
: Initial Data
YY SETTING DATA
No. MEANING DATA MEANING
00 Tenant number of the LDN assigned by 
CM50-0100
63
None Tenant 00
Tenant 63
01 TAS group number assigned by CM44-13 00
63
None TAS Group 00
TAS Group 63
02 Day mode destination of the LDN 00
07
08
09
None ATTCON LDN/TIE Key 0
ATTCON LDN/TIE Key 7
TAS (See CM53)
Station/Outside Party  Note
03 Night mode destination of the LDN 00
09
None As per YY = 02
Note
04 Day mode diversion for busy destination 
station00
01
07
08
09
None ATTCON Busy Key
Not used
TAS (See CM53)
Camp-on station
05 Night mode diversion for busy destination 
station00
09
None As per YY = 04
06 Day mode diversion for non-answering 
destination station00
01
07
08
None ATTCON “NANS” Key
Not used
TAS (See CM53)
~~
~~
~~
~
~
~
~ 
						

							ND-45669 (E) CHAPTER 3
Pag e 2 29
Revision 2.0
CM58
COMMAND CODE
TITLE:
LDN DIVERSION
58
07 Night mode diversion for non-answering 
destination station00
08
None As per YY = 06
08 Day mode station number/Abbreviate Code 
for Outside Party (LDN-Outside)X
XXXX
CXX
None Station No.
Abbreviated Code for Outside Party 
(XX: 00 - 31, See CM71-66)
09 Night mode station number/Abbreviate 
Code for Outside Party (LDN-Outside)X
XXXX
CXX
None Station No.
Abbreviated Code for Outside Party 
(XX: 00 - 31, See CM71-66)
10 Company Name data for Dialed Number 
Identification Service20
5F
NoneCharacter Code (Max. 8 digits)
(See CM77)
: Initial Data
YY SETTING DATA
No. MEANING DATA MEANING
~
~
~
~ 
						

							CHAPTER 3 ND-45669 (E)
Pag e 2 30
Revision 2.0
CM59
COMMAND CODE
TITLE:
TAS/ACD/UCD RELAY INTERRUPTION PATTERN
59
4. DATA TABLE:
1. FUNCTION:
This command is used to assign the interruption pattern on the TAS and ACD/UCD indicators controlled
via the PN-DK00 card.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
FUNCTION NUMBER PURPOSE DATA MEANING
00 TAS/ACD/UCD RELAY
INTERRUPTION PATTERN
(See CM44-13xx/14x)01 30 IPM
02 60 IPM
03 120 IPM
07 Steady on
FUNCTION
ST + 59 + DE + NUMBER + DE + + EXE
(2 digits)DATA
(2 digits)
[CM59] TAS/ACD/UCD Relay Interruption Pattern 
						

							ND-45669 (E) CHAPTER 3
Pag e 2 31
Revision 2.0
CM5A
COMMAND CODE
TITLE:
VIRTUAL LINE 
– VIRTUAL TRUNK PATH SETTING
5A
4. DATA TABLE:
1. FUNCTION:
Specify a path between the virtual line and virtual trunk for Wireless Communication System.
2. PRECAUTION:
Combination of the virtual line and the virtual trunk must be as follows:
• Level 0 Trunk No. and Level 1 Station No.
• Level 2 Trunk No. and Level 3 Station No.
3. ASSIGNMENT PROCEDURE:
YY BLOCK No. SETTING DATARELATED
COMMAND
00 000 – 169
VIRTUAL TRUNK No.BLOCK No.
(3 digits) STDE + 5AYY + +++DE
EXE
+(4 digits)
’ +
VIRTUAL STATION No.
(1-4 digits) +
DXXX , XXXX
Virtual Station No. X – XXXX
Virtual Trunk No. D000 – D255
[CM5A] Virtual Line – Virtual Trunk Path Setting 
						

							CHAPTER 3 ND-45669 (E)
Pag e 2 32
Revision 2.0
CM60
COMMAND CODE
TITLE:
ATT GROUP, FUNCTIONS
60
MAT
4. DATA TABLE:
1. FUNCTION:
This command is used to assign a number to an ATTCON for access on a tenant basis, and define the
consoles’ night switching ability, off-hook ringing, tone ringer, password code for Attendant Lockout
and Attendant Programming.
2. PRECAUTION:
(1) CM60 YY = 00, 01, 02, 04, 06 require a system reset after data setting.
(2) The password for ATTCON (YY = 30) cannot be assigned by the MAT mode menu.
(3) When assigning a password code for an ATTCON by CM60 YY = 30, the Function Number (0/1)
is required as the first data. The purpose of Function Numbers is shown below.
0: To assign a password for ATTCON Lockout
1: To assign a password for Attendant Programming
(DISA, System Speed Dialing, Date and Time, and Tone Ringer)
(4) This command is included in MAT mode menu “C2” (ATT Group, Functions [COM02]).
3. ASSIGNMENT PROCEDURE:
: Initial Data
YY GROUP NUMBER
RELATED
COMMAND
No. MEANING DATA MEANING
00
(
Group 
No.
)ATT GROUP 0
1
2
3ATT GROUP 0
ATT GROUP 1
ATT GROUP 2
ATT GROUP 3CM62
CM51 YY = 13
01
(
Master)Designation of Master ATT 
within ATT Group0
1 
Master ATT
Not Master ATT
Note:Master ATT must be
assigned to a single 
ATTCON within 
ATT Group.
STDE + 60YY + ++DE
(1 - 8 digits)DATA
++EXE ATTCON
NUMBER
(0 - 7)FUNCTION
NUMBER
(0/1)
INITIAL
INITIAL
[CM60] ATT Group, Functions 
						

							ND-45669 (E) CHAPTER 3
Addendum-002 Page 233
JANUARY, 1999 Revision 2.2
CM60
COMMAND CODE
TITLE:
ATT GROUP, FUNCTIONS
60
MAT
 
Note 1:These data are effective for NITE key on an ATTCON and Day/Night Mode Change on an
ATTCON. The NT switch is effective only on the Master ATTCON assigned by CM60 YY=01.
Note 2:In the initial data (NONE), the password code is set to “12345678”.
: Initial Data
YY GROUP NUMBER
RELATED
COMMAND
No. MEANING DATA MEANING
02
(A0)Trunk Restriction Class change by 
NT SwitchNote 10
1Effective
IneffectiveCM12
YY=01
04
(A2)Outgoing call restriction on night 
mode by NT SwitchNote 10
1Effective
IneffectiveCM30
YY=08
06
(A4)Day/Night mode change by NT
SwitchNote 10
1Effective
IneffectiveCM30 YY=02, 03, 
04, 05, 13, 14
CM76 Y=0, 1
CM58 YY=02–09
15
(F5)Location change of the Answer 
and Release key on the ATTCON0
1Key No. 25-Release,
Key No. 26-Answer
Key No. 25-Answer,
Key No. 26-Release
16
(F6)Off-Hook Ringing for ATTCON 0
1To provide
Not provided
17
(F7)ATTCON Multi-Function Key 0
1Ineffective
EffectiveCM90 YY=00
22 Kind of Attendant Console 0
1DESKCON 
(SN716 DESKCON)
ATTCON (SN610 ATTCON)
27
(TONE
RING)Tone Ringer for ATTCON 0
1
2
3600 + 700
480 + 606 
´ 8 (Hz)
1024 + 1285 
´ 16 (Hz)
480 + 606 
´ 16 (Hz)
30 Password for ATTCON X
XX...XX
NONEPassword code (Max. 8 digits) 
X = 0–9, A (*), B (#)
Note 2
INITIAL
INITIAL
INITIAL
INITIAL
~