NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Page 398 Addendum-002
Revision 2.2 JANUARY, 1999
CMD016
COMMAND CODE
TITLE:
STATION FEATURES
D016
4 . D ATA  TA B L E :
1. FUNCTION:
This command assigns the class functions for each class assigned by CMD015.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
1ST DATA
2ND DATA
DATA MEANING
XX05 Room status code sending to the PMS 0  : Not sent
1: Send
XX06 Room status processing is executed by operations on Front Desk Terminal 0  : No
1: Yes
XX07 Message Waiting, Restriction Level, Wake-Up Message sending to PMS 0  : No sent
1: Sent
XX16 Sending of detail information of C.O. outgoing calls to SMDR Terminal/PMS 
which is set to “4” by CMD001-80/100/1200  : Not sent
1: Send
XX17 Sending of detail information of C.O. outgoing calls to SMDR Terminal which 
is set to “5” by CMD001-80/100/1200  : Not sent
1: Send
XX21 Sending of detail information of Tie Line outgoing calls to SMDR Terminal 
which is set to “4” by CMD001-80/100/1200  : Not sent
1: Send
XX22 Sending of detail information of Tie Line outgoing calls to SMDR Terminal 
which is set to “5” by CMD001-80/100/1200  : Not sent
1: Send
XX30 Sending of detail information of C.O./Tie Line incoming calls to SMDR Termi-
nal, which is set to “4” by CMD001-80/100/120
0  : Not sent
1: Send
XX31 Send call information for C.O. outgoing calls through CCIS0  : Not sent
1: Send
Note:“XX” in the DATA column denotes the Station Class Number assigned by CMD015.
 + D016 +   +   +   +   + 
STDE1ST DATA
(4 digits)DE2ND DATA
(0/1)EXE
[CMD016] Station Features 
						

							ND-45669 (E) CHAPTER 3
Addendum-002 Page 399
JANUARY, 1999 Revision 2.2
CMD016
COMMAND CODE
TITLE:
STATION FEATURES
D016
XX32 Send call information for Tie Line outgoing calls through CCIS 0  : Not sent
1: Send
XX42 Message Waiting Message sending to PMS 0  : Available
1: Not available
XX43 Control of Restriction Message sending to PMS 0  : Available
1: Not available
XX44 Wake-up Message sending to PMS 0  : Available
1: Not available
XX45 Assignment the Administrative Station 0  : Not available
1: Available
XX55 Sending of detail information of C.O./Tie Line incoming calls to SMDR Termi-
nal, which is set to “5” by CMD001-80/100/1200 : Not sent
1: Send
XX58 Sending of detail information of incoming calls to CCIS 0  : Not sent
1: Send
: Initial Data
1ST DATA
2ND DATA
DATA MEANING
Note:“XX” in the DATA column denotes the Station Class Number assigned by CMD015. 
						

							CHAPTER 3 ND-45669 (E)
Pag e 4 00
Revision 2.0
CMD026
COMMAND CODE
TITLE:
ROUTE INDEX FOR CALL CHARGE DEVELOPMENT
D026
4. DATA TABLE:
• For each Table Number assigned by this command, the charging method for each dialed digit is
assigned by CMD027 as shown below.
1. FUNCTION:
This command is used to assign a Development Table Number for each outgoing trunk route.
2. PRECAUTION:
Although actual charging is not determined by the PBX, it is necessary to program this command and
CMD027 to get SMDR output.
3. ASSIGNMENT PROCEDURE:
: Initial Data
1ST DATA 2ND DATA REMARKS
XX : Outgoing Trunk Route
No. (0 - 63)XXX : Development Table No.
(2  - 254)
ST  +  D026  +  DE  +1ST DATA
(1 - 2 digits)+  DE  +2ND DATA
(1 - 3 digits)+  EXE
Trunk Route No.
Route XX
CMD026Dialed Digits
CMD027Charging Method Table
No.
XXX0
1
9
[CMD026] Route Index For Call Charge Development 
						

							ND-45669 (E) CHAPTER 3
Pag e 4 01
Revision 2.0
CMD027
COMMAND CODE
TITLE:
CALL CHARGE DEVELOPMENT TABLES
D027
4. DATA TABLE:
Note:The actual digits sent from a trunk should be assigned.
1. FUNCTION:
This command is used for assigning the charging method to each dialled digit on the basis of each Devel-
opment Table designated by CMD026.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
1S T DATA 2ND DATA
XXX
 X
Dialed digit (0 - 9, A(*), B(#)) Note
Development Table No. (000 - 255)1 : Do not send to SMDR terminal
XXX3 : Refer to next digit assignment
[XXX: Next Development 
Table No. (000-255)]
9 : Send to SMDR terminal
ST  +  D027  +  DE  +1ST DATA
(2 - 4 digits)+  DE  +  2ND DATA  +  EXE
[CMD027] Call Charge Development Tables 
						

							CHAPTER 3 ND-45669 (E)
Pag e 4 02
Revision 2.0
CMD031
COMMAND CODE
TITLE:
ROOM STATUS CODE
D031
4. DATA TABLE:
X: Room Status Code to be set.
1. FUNCTION:
This command is used to assign the desired functions for each Room Status Code which is dialed from a
guest room or a Front Desk Terminal
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
1ST DATA (X: ROOM STATUS CODE 1 - 8)
2ND DATA
DATA FUNCTION
X00 Room Cutoff set. 0 : No
1:Yes
X01 Room Cutoff is cancelled.
X02 Do Not Disturb is set.
X03 Do not Disturb cancelled.
X04 Wake Up Call is cancelled.
X05 Message Waiting Lamp is off.
X06 Check In Time is set.
X07 Check In time is cleared.
X08 Restriction for Toll Call and International Call is set.
X31 Dialing Room Status Code from guest room is permitted.
2ND DATA
(0/1)EXE1ST DATA
(3 digits) STDEDE + D031 + ++++
[CMD031] ROOM STATUS CODE 
						

							ND-45669 (E) CHAPTER 3
Pag e 4 03
Revision 2.0
CMD031
COMMAND CODE
TITLE:
ROOM STATUS CODE
D031
Example:The table below shows the examples of functions by this command. 
Note:
The Room Status Codes for Check In and Check Out are to be assigned by means of CMD001 – 12 and – 13.
ROOM STATUS CODEFUNCTION NUMBER
00 01 02 03 04 05 06 07 08 31
1Check In (Note) / ////
2Check Out (Note)/ // /
3 Under Cleaning / / / /
4 Cleaning Finished / / / / /
5Check Finished /////
6Out of Service / ////
7
8 
						

							CHAPTER 3 ND-45669 (E)
Pag e 4 04
Revision 2.0
CMD033
COMMAND CODE
TITLE:
ROUTE INDEX FOR CALL DEVELOPMENT
D033
4. DATA TABLE:
On the basis of each Table Number assigned by this command, the type of call to the dialed digits is
assigned by CMD034 as shown below.
1. FUNCTION:
This command is used to assign a Type of Call Identifying Development Table for each outgoing trunk
route.
2. PRECAUTION:
Although the type of Call Identifier has no meaning for the U.S. market, this command and CMD034
must be assigned to get SMDR output.
3. ASSIGNMENT PROCEDURE:
: Initial Data
1ST DATA 2ND DATA REMARKS
XX : Trunk Route Number
(0 - 63)XXX: Type of Call Development 
Table Number
(0
 - 127)
ST  +  D033  +  DE  +1ST DATA
(1-2 digits)+  DE  +2ND DATA
(1-3 digits)+  EXE
TRUNK ROUTE
ACCESS CODEROUTE XX
CMD033Ta b l e
XX0
1
2
9Ta b l e
XX0
1
2TOL L
LOCAL
TYPE OF
CALL
CMD034
[CMD033] Route Index For Call Development 
						

							ND-45669 (E) CHAPTER 3
Pag e 4 05
Revision 2.0
CMD034
COMMAND CODE
TITLE:
CALL DEVELOPMENT TABLES
D034
4. DATA TABLE:
Note 1:The actual digits sent from a trunk should be assigned.
Note 2:This feature restricts Toll Call and International Call. (Type of Call No. 2 and No. 3 assigned by
this command.)
1. FUNCTION:
This command is used to assign Type of Call to the dialed digits on each Type of Call Identifying Table
Number assigned by CMD033.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
1ST DATA 2ND DATA REMARKS
STDE + D034 + ++DE
(2 – 4 digits) 2ND DATA
+ + EXE(2 – 4 digits) 1ST DATA
XXXX
Dialed digit [0–9,A,(*),
B(#)]
Note 1
Call Development
Table Number (0–127)
Note 2
X1 : For assigning Type of Call
1
2
3
4
5
6
7
8
9: C.O. Call
: Toll Call
: International Call
Unused
:Tie Line Call
[CMD034] Call Development Tables 
						

							CHAPTER 3 ND-45669 (E)
Pag e 4 06
Revision 2.0
CMD034
COMMAND CODE
TITLE:
CALL DEVELOPMENT TABLES
D034
Example:Call Development Tables are assigned according to the following table.
Trunk Route
to set: Route 0
ACCESS
CODE = 0Command D033
ROUTE 0Command D034
ISD Call (000)
Toll Call (01 - 09)
Local Call (2 - 9)
DIGIT TYPE OF CALL
00
01
09
2
9ISD Call
Toll Call
Local Call
• CMD033
To Trunk Route 0, assign No. 0 Call
Development Table.
• CMD034
In No. 0 Call Development Table;
1. Set No. 1 Call Development Table to digit 0.2. Set “LOCAL CALL” to digit 2 - 9.
XX: 02 - 09
In No. 1Call Development Table;
3. Set “ISD CALL” to digit 0.
4. Set “TOLL CALL” to digit 1 - 9.
XX: 11 - 19 ST
DE + D033 ++DE + +EXE 0 +0
ST
DE + D034 ++DE + +EXE 10 +00ST
DE + D034 ++DE + +EXE 11 +XX
ST
DE + D034 ++DE + +EXE 31 +10
ST
DE + D034 ++DE + +EXE 21 +XX 
						

							ND-45669 (E) CHAPTER 3
Pag e 4 07
Revision 2.0
CMD035
COMMAND CODE
TITLE:
DESIGNATION OF PRINTER
D035
4. DATA TABLE:
1. FUNCTION:
This command is used to designate the printer for printout by key operation at each Front Desk Instru-
ment.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
1ST DATA
2ND DATA
DATA FUNCTION
X
XXXXFront Desk Instrument (Multiline Terminal) Primary Extension 
Number assigned by CM 10 (FX - FXXXX).0:Printer 0
1:Printer 1
ST   +   D035   +   DE   +1ST DATA
(1 - 4 digits)+   DE   +2ND DATA
(0/1 Data)+   EXE
~
[CMD035] Designation Of Printer