NEC Neax2000 Ivs Command Manual
Have a look at the manual NEC Neax2000 Ivs Command Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 3 ND-45669 (E) Pag e 2 94 Revision 2.0 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT 90 MAT • ATTCON Function Keys YY SETTING DATAFUNCTIONSTANDARD KEY SETTINGREMARKSRELATED COMMAND No. MEANING 00 (Key data)Setting of FunctionF6100 Room Cut Off (RC) For Hotel ATTCON Note 1 F6101 Message Waiting (MW) F6102 Do Not Disturb (DND) F6103 Wake Up/Do Not Disturb Override (WU/OV) F6104 Reset (RESET) F6105 Serial Call Set (SC) CM90-F6062 F6106 Flash over trunk (CAS) (SHF)CM35 YY=16 F6107 Busy Verification (BV) CM08-012 CM15 YY=09 F6108 Do Not Disturb Override (DNDOV)For Hotel ATTCON Note 2 F6109 Wake Up (WU) F6110 Note 3Mode (MODE) Day/Night mode change, ATT lockout F6111 Programming (PROG) System Speed Dialing Date and Time Tone Ringer Choice of Night Service F6112 Out pulse (PB signal) short (SPB)CM35 YY=26 F6113 Out pulse (PB signal) long (LPB)CM41 Y=0 Function No. 14 Note 1:Use the ANSWER key as the SET key for Hotel features. Note 2:Do not assign this data to key numbers 1 to 6. Note 3:For SN716 DESKCON, this data is not required.
ND-45669 (E) CHAPTER 3 Pag e 2 95 Revision 2.0 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT 90 MAT 00 (Key data)Setting of FunctionF6121 Last umber Redial/Stack Dial F6122 Calling Number/Calling Name Display for Caller ID Class F6123 Transfer to VMS F6144 Call Park-System CM08-445 F6150 F6159Paging 0 Paging 9CM08-445 F6200 Source (SRC) SRC F6201 Destination (DEST) DEST F6202 Cancel (CNL) CANCEL F6203 Talk (TALK) TALK F6204 Hold (HOLD) HOLD F6205 Start (START) F6240 F6245Loop 1 (LOOP1) Loop 6 (LOOP6)LOOP 1 LOOP 6 F1201 F1262Lamp indication when trunks are all busy in Trunk Group 01 (TGB01) Lamp indication when trunks are all busy in Trunk Group 62 (TGB62)Max. 6 keys per ATTCON Note 1CM30 YY=09 F7XXX XX XRelay Control Function Key Note 2CM44- XXX-1500 Note 1:Do not assign this data to key numbers 1 to 6. Note 2:Only one key assignment is allowed per relay circuit. YY SETTING DATAFUNCTIONSTANDARD KEY SETTINGREMARKSRELATED COMMAND No. MEANING ~~ ~~~ ~ ~ Card No. (00-31) assigned by CM44 Circuit No. (0-3) assigned by CM44
CHAPTER 3 ND-45669 (E) Pag e 2 96 Revision 2.0 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT 90 MAT • ATTCON Multi-Function Keys YY No.AT T C O N STATUS No.MEANINGSETTING DATAFUNCTION REMARKSRELATED COMMAND 00 00 (Idle State)Idle State F6100 Room Cut Off (RCOF) F6102 Do Not Disturb (DND) F6104 Reset (RESET) F6110 Mode (MODE) F6111 Programming (PROG)DISA, System Speed Dialing, Date and Time and Tone Ringer 01 (ANS & ORG)When answering or originatingF6105 Serial Call Set (SC) CM90-F6062 F6106 Flash over trunk (CAS, Centrex) (SHF)CM05 YY=16, 86 CM41 Y=2 Function No. 17 F6112 Out pulse (PB signal) short (SPB)CM35 YY=26 F6113 Out pulse (PB signal) long (LPB)CM41 Y=0 Function No. 14 F6203 Talk (TALK) 02 (STA busy)When the called station is busyF6107 Busy Verification (BV)Attendant Override CM08-012 CM15 YY=09 03 (STA DND)When the called station is in DNDF6108 Do Not Disturb Override (DDOV)
ND-45669 (E) CHAPTER 3 Pag e 2 97 Revision 2.0 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT 90 MAT Note 1:Use the ANSWER key as the SET key for Hotel/Motel features. Note 2:Call Processing keys or Loop keys should not be assigned to the Multi-Function Key (01 – 06). Note 3:When setting or cancelling a group of stations in DND/RC, use ATTCON status No. 00. Note 4:See related command, CM60 YY = 17. 00 04 (Hotel/ Motel)When accessing Hotel/Motel featuresF6100 Room Cut Off (RCOF)For Hotel/Motel ATTCON Note 1 F6101 Message Waiting (MW) F6102 Do Not Disturb (DND) F6104 Reset (RESET) F6109 Wake Up (WU) YY No.AT T C O N STATUS No.MEANINGSETTING DATAFUNCTION REMARKSRELATED COMMAND
CHAPTER 3 ND-45669 (E) Pag e 2 98 Revision 2.0 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT 90 MAT Note 5:If no data is set, the Multi-Function keys are automatically set by initial data/Resident System Program as follows: • Idle State • When answering or originating • When the called station is busy • When the called station is in DND • When accessing Hotel/Motel feature 010203040506 MODE: Mode PROG: ProgrammingPA 10:23 AM TUE 12 MODE PROGLOCKOUT/DAY 010203040506 SPB: Out Pulse Shor t LPB: Out Pulse Long SHF: Flash Over Trunk SC: Serial Call Set TA L K : Ta l k252 ANNCL1 10:23 AM TUE 12 SPB LPB SHF SC TALKLOCKOUT/DAY 010203040506 B.V: Busy Verification252 ANNCL1 10:23 AM TUE 12 B.V LOCKOUT/DAY BSY 010203040506 DDOVR: Do not Disturb Override252 ANNCL1 10:23 AM TUE 12 W DDOVRLOCKOUT/DAY DND 010203040506 RC: Room Cut Off MW: Message Waiting DD: Do not Disturb WU: Wake Up RESET: Reset252 ANNCL1 10:23 AM TUE 12 RC MW DD WU RESETLOCKOUT/DAY
ND-45669 (E) CHAPTER 3 Pag e 2 99 Revision 2.0 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT 90 MAT 4.3 Add-On Module : Initial Data YY SETTING DATA RELATED COMMAND No. MEANINGKEY No.DATA MEANING 00 (Key Data)Setting of Functions 30 54X XXXX (STA No.)Station Number • Primary Extension Number (FX-FXXXX) • Multiline Number (Ordinary Station) • Multiline Number (assigned by CM11) X=0-9, A (*), B (#)CM10 CM11 A000 A031 A100 A131Automatic Intercom Number CM11 CM56 YY=10 A200 A700 A201 A701 A224 A724Manual Intercom Number CM11 CM56 YY=11 B000 B900 B001 B901 B024 B924Dial Intercom Number CM11 CM56 YY=12 DXXX (TRK No.)Trunk Number (XXX=000-255)CM10 CM30 YY=18 ~~~~~~ ~~~ ~
CHAPTER 3 ND-45669 (E) Pag e 3 00 Revision 2.0 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/SN610 ATTCON/ADD-ON MODULE KEY ASSIGNMENT 90 MAT 00 (Key Data)Setting of Functions 30 89F11XX XX 00: Station Speed Dialing 00 99: Station Speed Dialing 99CM73 (SPD0099) CM74 00 Setting of Functions 87 89F0043 (D/N)Day/Night Key Note:Any one of key numbers 87 through 89 can be used for the Day/Night key. 01 (RG)Tone Ringer enabled on call termination30 540 1Disabled Enable 03 Ringer sending method when terminating a call to Line/Trunk key on the Multiline Terminal30 540 1Delayed Ringing No delayed ringing Note:Delayed Ringing may be assigned to the first 16 Line/Trunk keys (Key Nos. 30 through 45).CM41 Y=1 Function No. 09 : Initial Data YY SETTING DATA RELATED COMMAND No. MEANINGKEY No.DATA MEANING ~ ~ ~ ~~ ~
ND-45669 (E) CHAPTER 3 Pag e 3 01 Revision 2.0 CM93 COMMAND CODE TITLE: PRIME LINE 93 MAT 4. DATA TABLE: Note:Any station number or Virtual Line number can be assigned to the Prime Line. A single-line telephone cannot be assigned as the Prime Line. 1. FUNCTION: This command is used to assign the prime line to a station line or a trunk line on a Multiline Terminal. The prime line is the line seized when the Multiline Terminal user goes off-hook or presses the speaker button. 2. PRECAUTION: (1) Any one station line or trunk line provided on the Multiline Terminal can be assigned as Prime Line. (2) This command is included in MAT mode menu “A2” [D term Key [COM01]). 3. ASSIGNMENT PROCEDURE: MY LINE NUMBERSETTING DATA RELATED COMMAND DATA MEANING X XXXXX XXXXStation Number/Virtual Line Number NoteCM10, CM11 D000 D255Trunk Number CM30 YY = 02, 03, 18 ST PRIMARY DE +93 + ++ DE NUMBERSTATION ++EXE EXTENSION NUMBER (1 – 4 digits)(1 - 4 digits)NUMBERTRUNK (1 - 4 digits) ~~ ~ [CM93] Prime Line
CHAPTER 3 ND-45669 (E) Pag e 3 02 Revision 2.0 CM94 COMMAND CODE TITLE: MULTILINE TERMINAL ONE-TOUCH MEMORY 94 MAT 4. DATA TABLE: Note 1:If “4” is selected, the first 10-Slot Memory Block number must be “00” through “49”. Note 2:1000-Slots Memory Block Number 8-F can be used when the system provides the Extension Mem- ory card. If assigning the station number to One Touch keys using this memory area, the lamp does not show the busy state. 1. FUNCTION: This command is used to assign memory for the storage of numbers accessed by the one-touch keys on a Multiline Terminal. 2. PRECAUTION: This command is included in MAT mode menu “A2” (D term Key [COM01]). 3. ASSIGNMENT PROCEDURE: MY LINE NUMBERSETTING DATA DATA MEANING X XXXXXXXXXX ST PRIMARY DE +94 + ++ DE (6 digits)D ATA ++EXE EXTENSION NUMBER (1 – 4 digits) ~Quantity 10-Slot Memory Blocks (01/02) 01:Multiline Terminal (10 memories) 02:Multiline Terminal (20 memories) XX XXXX Facility for programming the dialed number from the station (0/1 = Effective/Ineffective) First 10-Slot Memory Block (00-99) The 1000-slots memory Block num- ber (0-4, 8-F) Note 1, Note 2 [CM94] Multiline Terminal One-Touch Memory
ND-45669 (E) CHAPTER 3 Pag e 3 03 Revision 2.0 CM96 COMMAND CODE TITLE: DSS CONSOLE NUMBER 96 MAT 4. DATA TABLE: 1. FUNCTION: This command is used to assign a DSS Console to a station, Multiline Terminal or attendant console. 2. PRECAUTION: This command is included in MAT mode menu “E3” (DSS Console No. & Keys [COM02]). 3. ASSIGNMENT PROCEDURE: DSS CONSOLE NUMBERSETTING DATA RELATED COMMAND DATA MEANING 00 31 (See CM10, E100-E131)X XXXXSingle Line Telephone Station Number or Primary Extension Number of Multiline TerminalCM10-E100-E131 CM97 E000 E007ATTCON CM10-E000-E007 SN61 x: CM10, E000-E007 STDE +96 + ++DE (1 - 4 digits)D ATA ++EXE DSS CONSOLE NUMBER (2 digits) ~~ ~ [CM96] DSS Console Number