NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Page 234 Addendum-002
Revision 2.2 JANUARY, 1999
CM61
COMMAND CODE
TITLE:
EXTERNAL KEY FUNCTION
61
MAT
4 . D ATA  TA B L E :
1. FUNCTION:
This command is used to activate and specify the function of the switch closure detection circuit 
(PN-DK00) card when interfaced with external keys.
2. PRECAUTION:
This command is included in MAT mode menu “E4” (External Key function [COM02]).
3. ASSIGNMENT PROCEDURE:
: Initial Data
KEY NUMBER YY SETTING DATA
RELATED
COMMAND
No. MEANING No. MEANING DATA MEANING
XXX
Note:Card number
corresponds
to 00 - 63 of
CM10 E900 -
E963.00
(TN)Destination of Tenant 00
63Tenant 00
Tenant 63
01
(A0)Change Day/Night trunk re-
striction Class by external 
key0
1
 
Effective
IneffectiveCM12
YY = 01
03
(A2)Outgoing call restriction on 
night mode by external key0
1
 
Effective
IneffectiveCM30
YY = 08
05
(A4)Day/Night mode change by 
external key0
1
 
Effective
IneffectiveCM30 YY = 02, 
03, 04, 05, 13, 
14, 26
CM76 Y = 0, 1
CM58
YY = 02 - 09
06
(A5)Even if station-to-station 
call is restricted, calling 
tenant is allowed to cancel 
restriction by external key0
1
 
Effective
IneffectiveCM63
Y = 1
30 External key for alarm 
clearing00 MJ/MN Alarm 
Clear key
STDE + 61YY + ++DE
(1 - 3 digits)D ATA
++EXE KEY NUMBER
(3 digits)
X XX
Circuit No. 
(0-3)
Card No. 
(00-63)
~~
[CM61] External Key Function 
						

							ND-45669 (E) CHAPTER 3
Pag e 2 35
Revision 2.0
CM62
COMMAND CODE
TITLE:
TENANTS FOR EACH ATT GROUP
62
INITIAL
4. DATA TABLE:
1. FUNCTION:
This command is used to assign which tenants are handled by each ATTCON Group.
2. PRECAUTION:
(1) This command requires a system reset after data setting.
(2) Multiple tenants can be assigned to one ATT Group, but one tenant cannot be assigned to more than
one ATT Group.
3. ASSIGNMENT PROCEDURE:
: Initial Data
Y TENANT SETTING DATA
RELATED
COMMAND
No. MEANING No. MEANING No. MEANING
0
1
2
3ATT GROUP 0
ATT GROUP 1
ATT GROUP 2
ATT GROUP 300
63Tenant 00
Tenant 630
1
 
To be handled
Not to be handledCM60 YY = 00
STDE + 62Y + ++DE
(1 digit)DATA
++EXE TENANT
NUMBER
(2 digits)
~~
[CM62] Tenants For Each Att Group 
						

							CHAPTER 3 ND-45669 (E)
Page 236 Addendum-001
Revision 2.1 AUGUST, 1998
CM63
COMMAND CODE
TITLE:
RESTRICTION OF INTER-TENANT CONNECTION
63
4 . D ATA  TA B L E :
1. FUNCTION:
This command is used to define the restrictions on inter-tenant access.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
Y TENANT SETTING DATA
RELATED
COMMAND
No. MEANING No. MEANING No. MEANING
0 TAS answer from 
another tenantXXXX 0
1
 
TAS allowed
TAS not allowedCM53 Y = 4
CM30 YY = 17
1 Restriction of
Inter-office
ConnectionXXXX 0
1
 
Connection
restricted
Connection
allowedCM61
YY = 06
CM08 - 150
2 Restriction of
incoming DID/
Tie line call/
Automated
AttendantXXXX 0
1
 
Termination
restricted
Termination
allowed
STDE + 63Y + ++DE
(1 - 4 digits)D ATA
++EXE TENANT-A
(2 digits)+TENANT-B
(2 digits)
XX
(TENANT-B: 00-63)
Tenant number of 
Trunk XX
(TENANT-A: 00-63)
Tenant number of 
TAS Answer Station
XX
(TENANT-B: 00-63)
Tenant number of 
Called Station XX
(TENANT-A: 00-63)
Tenant number of 
Calling Station
XX
(TENANT-B: 00-63)
Tenant number of 
Trunk XX
(TENANT-A: 00-63)
Tenant number of 
called station
[CM63] Restriction of Inter-Tenant Connection 
						

							ND-45669 (E) CHAPTER 3
Addendum-002 Page 237
JANUARY, 1999 Revision 2.2
CM64
COMMAND CODE
TITLE:
AUTOMATED ATTENDANT
64
4. DATA TABLE:
Note:If no tone connection is required, Dial Tone sending can be stopped by CM48 Y=2.
1. FUNCTION:
This command defines the answering system of the Automated Attendant feature.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
Y
TENANTSETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
0 Setting of
Answering 
SystemXX: 00 – 63 00
01
02
03 Dial Tone Connection
Not used
1st Message and then Dial Tone
Connection
Dial Tone ConnectionCM30 YY=02, 03
CM48 Y=2
CM41 Y=0
Function No. 43
CM45 Y=2
CM49 
CM62
CM63 Y=2
1 Tenant Number 
for Music on 
HoldXX: 00 – 63 00
09TNT Number Assigned in CM10 CM10 – DA00-DA09
CM48
CM08-388
CM44
2 Setting of 
Answering 
System for Night 
ModeXX: 00 – 63 00
01
02
03DT Connection
Hold T one on MP card + DT  Con-
nection
Night Message (Assigned by 
CM49 YY=00-02XX)
According to the data set by 
CM64 Y=0CM30 YY=02, 03
CM49 YY=00-02XX, 
YY=02
CM49 YY=00-01XX
CM64 Y=0
STDE + 64Y + ++DE
(1 digit)DATA
++EXE TENANT NUMBER
(2 digits)
~
[CM64] Automated Attendant 
						

							CHAPTER 3 ND-45669 (E)
Pag e 2 38
Revision 2.0
CM65
COMMAND CODE
TITLE:
SERVICE FEATURES ON TENANT BASIS
65
4. DATA TABLE:
1. FUNCTION:
This command is used to define the features available in each tenant.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
Y
TENANTSETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
23 Call Forwarding type when an
internal call from station is termi-
natedXX: 00 – 63 0
1Split Call Forwarding–All Calls/
Busy Line/No Answer
Call Forwarding–All Calls/Busy 
Line/No Answer
24 Call Forwarding type when a C.O. 
incoming call is terminated0
1Split Call Forwarding–All Calls/
Busy Line/No Answer
Call Forwarding–All Calls/Busy 
Line/No Answer
25 Call Forwarding type when a Tie 
Line incoming call is terminated0
1Split Call Forwarding–All Calls/
Busy Line/No Answer
Call Forwarding–All Calls/Busy 
Line/No Answer
26 Number Display through CCIS 
for SMDR between 2000 IVS and 
NEAX24000
1My Line Number
Sub Line Number
27 Service feature for each tenant 0
1ACD
Not ACD
STDE + 65YY + ++DE
(1 digit)DATA
++EXE TENANT NUMBER
(2 digits)
[CM65] Service Features on Tenant Basis 
						

							ND-45669 (E) CHAPTER 3
Addendum-001 Page 239
AUGUST, 1998 Revision 2.1
CM65
COMMAND CODE
TITLE:
SERVICE FEATURES ON TENANT BASIS
65
: Initial Data
Y
TENANTSETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
28 RR sending priority when receiv-
ing SCFXX: 00 – 630
1Send RR (Returned Result) after 
SMFN
Send RR (Returned Result) before 
SMFN
30 VMS Password Privacy 0
1VMS Password Privacy Allowed
Not allowedCM13
YY=10
50 When the transferred destination 
does not answer0
1Connection of the Transferred 
Trunk Line Message (No Answer)
Recall transferring stationCM49
YY=00, 06
51 When the transferred destination 
is busy0
1Connection of the Transferred 
Trunk Line Message (Busy)
Recall transferring stationCM49
YY=00, 07
[CM65] Service Features on Tenant Basis 
						

							CHAPTER 3 ND-45669 (E)
Pag e 2 40
Revision 2.0
CM71
COMMAND CODE
TITLE:
MEMORY ALLOCATION FOR SYSTEM SPEED DIALING
71
MAT
1. FUNCTION:
This command is used to allocate memory area for System Speed Dialing to tenants, attendants and Hot
Line outside stations.
2. PRECAUTION:
(1) System Speed Dialing has 300 memory locations system-wide; this is referred to as a “Memory
Block” (see figure below). Each location where a dialed number is stored is called a “Memory
Slot”.
Example:The System Speed Dialing memory is assigned to three tenants as follows:
(2) Limitation on Memory Slot allocation:
• In a single-tenant system, Tenant 00 can be assigned a maximum of 300 memory slots.
• Per Tenant: Maximum of 300 memory slots
• For Hot Line outside Call: Maximum of 100 memory slots (maximum num-
ber of Hot Lines)
• For Route Advance from Tie Line to C.O. line: Maximum of 64 memory slots (maximum number
of Trunk Routes) 
Memory Block 
000
001
299
~
Memory Slot
TENANTQUANTITY OF SLOTS RANGE OF SLOT NUMBERS
00 20 000 - 019
01 15 020 - 034
02 10 035 - 044
[CM71] Memory Allocation for System Speed Dialing 
						

							ND-45669 (E) CHAPTER 3
Pag e 2 41
Revision 2.0
CM71
COMMAND CODE
TITLE:
MEMORY ALLOCATION FOR SYSTEM SPEED DIALING
71
MAT
(3) There is a maximum of 300 memory slots assigned by this command. However, if required, another
1000 memory slots can be added. In this case, the maximum number of digits stored is 16. These
additional 1000 memory slots are to be assigned with CM 08-110, 111, 112, 176, and CM73 and
CM74.
(4) The Abbreviated codes for System Speed Dialing are automatically determined by assigning this
command on a tenant basis, as shown below.
(5) The Resident System Program allocates 100 memory slots to Tenant 01.
(6) This command is included in the MAT mode menu “E11” [ Speed Dialing (COM02)].
3. ASSIGNMENT PROCEDURE:
000
001
002
01900
01
02
19 (Memory
Slot No.)(Abbrev.
Code) Tenant 00020
021
022
03400
01
02
14 (Memory
Slot No.)(Abbrev.
Code) Tenant 01035
036
037
04400
01
02
09 (Memory
Slot No.)(Abbrev.
Code) Tenant 02
~ ~
~
~ ~ ~
KIND OF
ST + 71 + DE + CALLING PARTY + DE + + EXE
(2 digits)DATA
(6 digits 
						

							CHAPTER 3 ND-45669 (E)
Pag e 2 42
Revision 2.0
CM71
COMMAND CODE
TITLE:
MEMORY ALLOCATION FOR SYSTEM SPEED DIALING
71
MAT
4. DATA TABLE:
KIND OF CALLING PARTY SETTING DATA
No. MEANING MEANING MEANING
00
63Tenant 00
Tenant 63XXXXXX
XXX XXX
• First Memory Slot
Number in Block: 000-299
• Number of Slots to 
be assigned in Block: 001-300
64 Exclusively for ATTCON
65 Exclusively for Hot Line Outside 
Call (Related Command: CM52)
66 Exclusively for Route Advance 
from Tie line to C.O. line 
(Related Command: 
CM35 YY = 40,
CM30 YY = 04, 05
CM58 YY = 08, 09: CXX)
68 The terminating number of the op-
posite office on alternative ISDN 
connectionXXXXXX
XXX XXX
• First Memory Slot
Number in Block: 000-299
• Number of Slots to 
be assigned in Block: 001-032
~~Number of Slots to be 
assigned in Block
First Memory Slot 
Number in Block
Number of Slots to be 
assigned in Block
First Memory Slot 
Number in Block 
						

							ND-45669 (E) CHAPTER 3
Pag e 2 43
Revision 2.0
CM72
COMMAND CODE
TITLE:
STORED NUMBER FOR SYSTEM SPEED DIALING
72
MAT
(1) The stored number, for System Speed Dialing, is assigned for each Memory Slot Number, not for the
abbreviated code of each calling party. When assigning stored numbers, the correspondence between
Memory Slot Numbers and abbreviated codes is first to be determined for each kind of calling party,
and then the stored numbers are to be assigned according to the determined correspondence, with each
exclusive memory area assigned in CM71 taken into consideration.
(2) Each stored number should be assigned, including the access code for C.O. line/Tie line, together with
the party’s number. The format is as follows:
Stored Number = Access Code + Separator Mark + Called Party’s Number
• Access Code: Access Code (Maximum of 2 digits)
• Separator Mark:  to be inserted between the Access Code and the Called Party’s 
Number
• Called Party’s Number: C.O. network subscriber number or Station number in the distant PBX
(maximum of 26 digits)
1. FUNCTION:
This command is used to enter the stored number for the System Speed Dialing feature into the memory
allocated with CM71.
2. PRECAUTION:
(1) When displaying the data, the access code corresponding to the Memory Slot Number is indicated
by the very first   , and the stored number is indicated by the next   . When the number of
digits of the stored number exceeds 16, the 17th to 26th digits are indicated by the next    .
(2) Data can only be changed when the access code is displayed. Enter the data in the following order:
new access code, comma, the called number, and    . For clearing the data, enter the data in the
following order: access code on the display, comma, “CCC”, and   .
(3) If “C” is inserted in the called number, when using System Speed Dialing for an Outgoing Tie Line
Call, it can be used as a fixed-length pause (1.5 sec.). To provide a programmable pause with the
stored number, insert “D” instead of “C”. The length of the programmable pause is assigned with
CM41 Y = 0, Function 38.
(4) This command is included in the MAT mode menu “E11” (Speed Dialing [COM02]).
3. ASSIGNMENT PROCEDURE:
DEDE
DE
EXE
EXE
MEMORY SLOT
ST + 72 + DE + NUMBER + DE + + EXE
(3 digits)STORED NUMBER
(Max. 28 digits)
,
[CM72] Stored Number for System Speed Dialing