NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Pag e 4 08
Revision 2.0
CMD100
COMMAND CODE
TITLE:
SYSTEM DATA PARTIAL CLEAR
D100
AP OFF LINE
Note:Before clearing the system data by this command, make the following switch setting on the PN-AP00 card.
1. FUNCTION:
This command is used to delete the data related only to the designated Command Code among the Sys-
tem Data for Billing and for assigning “0” as the data.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
STDE + D100 + ++DE + +EXE DXXXCCC
Command Code of the data to be deleted
4
3
2
1 SW1
ON
: Position to be set [CMD100] System Data Partial Clear 
						

							ND-45669 (E) CHAPTER 3
Pag e 4 09
Revision 2.0
CMD101
COMMAND CODE
TITLE:
SYSTEM DATA ALL CLEAR
D101
AP OFF LINE
Note:Before clearing the system data by this command, make the following switch setting on the PN-AP00 card.
1. FUNCTION:
This command is used to delete all the System Data for Billing and for assigning the initial data.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
STDE + D101 + ++DE + +EXE 0000 CCC
4
3
2
1 SW1
ON
: Position to be set [CMD101] System Data All Clear 
						

							CHAPTER 3 ND-45669 (E)
Pag e 4 10
Revision 2.0
CMD102
COMMAND CODE
TITLE:
ADDITIONAL MEMORY CLEAR
D102
AP OFF LINE
Note 1:By entering the 1st data “0000”, the status of the additional memory (SRAM card) will display
as follows:
Note 2:Before clearing system data by this command, make the following switch setting on the PN-AP00
card.
1. FUNCTION:
When mounting additional memory (SRAM card), this command is used to delete its stored data.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
STDE + D102 + ++DE + +EXE 0000
CCC
(4 digits)
0 : SRAM card was not mounted
1 : SRAM card was initialized 0 0 X
4
3
2
1 SW1
ON
: Position to be set [CMD102] Additional Memory Clear 
						

							ND-45669 (E) CHAPTER 4
Page 411
Revision 2.0
RESIDENT SYSTEM PROGRAM
CHAPTER 4 RESIDENT SYSTEM PROGRAM
1. GENERAL
The resident system program generates system data automatically according to the system hardware configu-
ration, thereby providing immediate operation and shorter programming time. When activated, the system
scans hardware configuration (such as line/trunk card location) and assigns the system data (such as station
numbers, trunk numbers, etc.) according to a predetermined generic program assignment.
2. PROCEDURE FOR LOADING THE RESIDENT SYSTEM PROGRAM
STEP 1 Mount the cards on PIMs.
STEP 2 Set SW3 of the MP card to “C”.
STEP 3 Press SW1 of the MP card.
STEP 4 Confirm the status of MJ/MN lamp on the PWR card.
• When the MN lamp lights, the office data is normally registered.
• When the MJ lamp lights, the office data is not normally registered.   
Repeat STEP 2 and STEP 3.
STEP 5 Set SW3 of the MP card to “0”.
STEP 6 P
ress SW1 of the MP card.
3. SERVICE CONDITIONS
(1) This service is applicable for equipment installed in PIM 0 through PIM 3. 
(2) Data for any vacant slot is not assigned.
(3) Virtual stations are not assigned.
(4) A line/trunk card (PN-AUCA/DK00/CFT) is not assigned, even if mounted.
(5) An application card (PN-AP00/AP01/24DTA/SC00/SC01/ME00) is not assigned, even if mounted.
(6) No tenant assignment is provided.
(Tenant 01 is assigned)
(7) Details of Resident System Program
For the other commands which are not described in Table 4-1 through Table 4-11, the initial data is loaded
by the Resident System Program. 
						

							CHAPTER 4 ND-45669 (E)
Page 412 Addendum-002
Revision 2.2 JANUARY, 1999
RESIDENT SYSTEM PROGRAM
4. PROGRAMMED DATA TABLES
• Basic Service Feature (CM08)
The following data is assigned on a per service feature basis.
Table 4-1  Basic Service Feature
: Initial Data
CM08
FEATURE 
No.DATA  
0/1FEATURE 
No.DATA  
0/1FEATURE
No.DATA 
0/1FEATURE
No.DATA  
0/1FEATURE
No.DATA  
0/1FEATURE 
No.DATA 
0/1FEATURE 
No.DATA 
0/1
012 1 050  1 101 1 150 1 221 1 264 1 379 1
014 051 102 0 151 1 222 1 265 380
018 055 103 0 153 0 227 1 267 381
021 056 104 1 155 1 228 0 268 382 1
025 057 109 1 156 0 232 1 269 390 0
026 058 110 157 1 233 0 270 391 1
028 062 111 158 234 1 271 394
029 063 1 112 161 235 1 274 400
032 067 1 113 162 1 236 1 280 401
035 068 0 115 163 0 237 1 281 403
036 069 1 116 165 1 238 282 405
040 076 119 168 239 283 450
043 094 123 171 241 284 451 1
044 095 124 172 244 286
045 096 1 125 176 245 287
048 1 128 177 246 293
130 178 1 250 294
133 179 0 251 311
135 180 1 252 319
136 181 253 322
137 183 254 324
138 185 255 331
139 187 259 333
141 193 262 1 334
142 194 352
143 199 353
145 200 357
146 201 359
147 204 361
148 205 362
149 1 206 1 363
208 0 366
212 1 369
214 370
215 371
216 372
217 1 378 1 
						

							ND-45669 (E) CHAPTER 4
Page 413
Revision 2.0
RESIDENT SYSTEM PROGRAM
• Station Number, Trunk Number, Card Number (CM10)
The following data is assigned according to the sequential slot location number of the associated circuit
cards.
Note:If the DSS Console is not connected to the system, though the PN-4DLC card is mounted in the slot, the
data (F200-F455) for Multiline Terminal is assigned.
Table 4-2  Station Number, Trunk Number, Card Number
CARD PURPOSE ASSIGNED DATA REMARKS
PN-4LC Single  Line  Telephone 200  –  455 Station Numbers 200 through 455 for Single Line 
Telephone and Multiline Terminal are assigned 
according to sequential slot location number of 
associated circuit card.
SN610 ATTCON Numbers E004 through E007 
are assigned according to sequential slot location 
number of associated circuit card. PN-4DLC
PN-2DLCBMultiline Terminal F200 – F455
PN-2DLCC SN610 ATTCON E004 – E007
PN-4COT
PN-2COT
PN-2ODTTrunk D000 – D255
PN-8RST DTMF Receiver E200 – E203 (PIM0/1)
E204 – E207 (PIM2/3)
Consecutive card number beginning at 00 is
assigned according to the sequential slot location 
number of the associated circuit cards. PN-2DAT Digital Announcement 
TrunkEB000 – EB031
(PIM0/1)
EB032 – EB063
(PIM2/3)
PN-CP03 DTMF Receiver E200 – E203 
						

							CHAPTER 4 ND-45669 (E)
Page 414 Addendum-002
Revision 2.2 JANUARY, 1999
RESIDENT SYSTEM PROGRAM
• Station Class Data (CM12, 13)
The following data is assigned on a per station basis.
Table 4-3  Station Class Data: Initial Data
CM10 CM12
STATION No.
TRUNK No.
CARD No.
(1–5 DIGITS)YY
00 01 02 03 04 05 07 12 13 16
0
2DAY NI GHT A B
00
1500
630/100
15x
xxxx00
15D000
D255x
xxxx 1
81
800
1500
15
31 1 15151501115
200 3 1 1 15 15 15 01 1 15
201 3 1 1 15 15 15 01 1 15
202 3 1 1 15 15 15 01 1 15
456
: Initial Data
CM10 CM13
STATION No.
TRUNK No.
CARD No.
(1–5 DIGITS)YY
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 21 22 23 29
0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1 0/1
11111111111111111111
200 11101111111111111111
201 11101111111111111111
202 11101111111111111111
456
~
~
~
~
~
~
~
~ ~
~
~
~ 
						

							ND-45669 (E) CHAPTER 4
Page 415
Revision 2.0
RESIDENT SYSTEM PROGRAM
• Number Plan (CM20)
The following data is assigned for access code of each service feature.
Table 4-4  Numbering Plan
CM20
Y (0–3) ACCESS CODE SETTING DATA SERVICE FEATURES
0 0 800 Operator Call
11 046 Call Hold
2, 3 or 4 803 First Digit of Three Digit Station Number
50 A30 Internal Zone Paging Group 0
For calling 51 A31 Group 1
52 A32 Group 2
53 A33 Group 3
54 A34 Group 4
55 A38 Internal Zone Paging Group 0
For answering 56 A39 Group 1
57 A40 Group 2
58 A41 Group 3
59 A42 Group 4
5* 024 Automatic Wake Up/Timed ReminderSet
5# 025 Cancel
60 A63 Voice Call/Ring Tone Programming
62 A10 Assignment of Station Name
66 039 BGM on Multiline Terminal Set/Reset
68 043 Day/Night Mode Change by Station Dialing
6* 008 Call Park-System Set
6# 009 Call Park-System Retrieve
72 047 TAS Answer A
73 021 Call Pickup – Direct
74 020 Call Pickup – Group
75 037 Call Pickup – Designated Group
7* 065 Station Speed Dialing Entry
7# 066 Cancel 
						

							CHAPTER 4 ND-45669 (E)
Pag e 4 16
Revision 2.0
RESIDENT SYSTEM PROGRAM
0 9 100 Trunk Access Code RT00
81 101 RT01
82 102 RT02
83 104 RT04
84 105 RT05
85 106 RT06
86 107 RT07
87 081 Individual Trunk Access
*1 004 Trunk Queuing – Outgoing Set
#1 005 /Call Back Cancel
*2 007 Camp-On by Station (Transfer Method)
#2 A25 Camp-On by Station (Call Waiting Method)
*4 006 Executive Override
*5 010 Call Forwarding – All Calls Entry
#5 011 Cancel
*6 012 Call Forwarding – No Answer Entry
#6 013 /Busy Line Cancel
*7 018 Call Forwarding – Designation Entry
#7 019 Cancel
*8 022 Do Not Disturb Set
#8 023 Cancel
*9 040 MW Lamp Control Set
#9 041 Reset
** 069 Last Number Redial
*# 085 Account Code Entry
#* 064 Station Speed Dialing Origination
## 067 System Speed Dialing OriginationTable 4-4  Numbering Plan (Continued)
CM20
Y (0–3) ACCESS CODE SETTING DATA SERVICE FEATURES 
						

							ND-45669 (E) CHAPTER 4
Page 417
Revision 2.0
RESIDENT SYSTEM PROGRAM
• Trunk Data (CM30)
The following data is assigned according to the type of trunk card.
Table 4-5  Trunk Data
:  Initial Data
CM30
TYPE OF 
TRUNK 
CARDYY
00 01 02 03 04 05 07 08 09 13 14 15
00
6300
6300
3100
31X
XXXX
EBXXXX
XXXX
EBXXX000
0290/100
6200
1500
1500
15
01 31 31 1 15 15 15
PN-4COT 00 01 02 02 NONE NONE 1 NONE 15 15 15
PN-2ODT 02 01 31 31 NONE NONE 1 NONE 15 15 15