NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Pag e 3 22
Revision 2.0
CMA8
COMMAND CODE
TITLE:
CCIS ROUTING LABEL ASSIGNMENT
A8
4. DATA TABLE:
1. FUNCTION:
This command is used to assign a destination office for a message to be transferred (e.g. service informa-
tion) and the Common Channel Handler (CCH) which will accommodate the message.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
1S T DATA 2ND DATA
RELATED
COMMAND
DATA MEANING DATA MEANING
00001
16367
NoteDestination Point Code (DPC) 
sent from distant office0
3CCH0
CCH3CM06 YY= 07
Note:A maximum of 256 DPCs per system can be assigned.
ST  +  A8  +  DE  +1st DATA
(5 digits)+  DE  +2nd DATA
(1 digit)+  EXE
~~~
[CMA8] CCIS Routing Label Assignment 
						

							ND-45669 (E) CHAPTER 3
Pag e 3 23
Revision 2.0
CMA9
COMMAND CODE
TITLE:
ISDN D-CHANNEL ASSIGNMENT
A9
INITIALMAT
4. DATA TABLE:
1. FUNCTION:
This command is used to assign various data to each D-Channel Handler (DCH) for ISDN-Primary Rate
Access.
2. PRECAUTION:
This command requires a system reset after data setting.
3. ASSIGNMENT PROCEDURE:
1S T DATA 2ND DATA
RELATED
COMMAND
No. MEANING DATA MEANING
00 Assignment of trunk used as 
D-Channel000
255Trunk Number assigned by CM07 
YY = 01CM07 YY= 01
ST   +  A9YY  +  DE  +  DCH No. (0 - 3)  +  DE  + +  EXE2nd DATA
(3 digits)
~
[CMA9] ISDN D-Channel Assignment 
						

							CHAPTER 3 ND-45669 (E)
Page 324 Addendum-001
Revision 2.1 AUGUST, 1998
CMAA
COMMAND CODE
TITLE:
DTI/DCH/CIR CARD FUNCTIONS
AA
4 . D ATA  TA B L E :
Note 1:This data is effective only when CMAA YY=01 is set to 0 (12-Multi Frame).
Note 2:NI-1 is supported on the BRT card only.
1. FUNCTION:
This command assigns functions to DTI, BRI and DCH card.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
  +AAYY+    +   +   + 
: Initial Data
YY SETTING DATA
RELATED 
COMMAND
No. MEANING DATA MEANING
00 Data Mode
(for 24-DTI card)0
1Based on AT&T Specifications
Not used
01 Frame Configuration
(for 24-DTI card)0
112-Multi Frame (D4)
24-Multi Frame (ESF)
02 ZCS (Zero Code Suppression)
(for 24-DTI card)
Note 10
1Available (Non Transparent)
Not available (Transparent)
03 Control Mode
(for 24-DTI card)0
6
7Not assigned
Channel Associated Interoffice Signaling/
Common Channel Interoffice Signaling
06 ISDN protocol type
(for DCH/BRI card)20
21
27
28
63AT&T (#4, #5 ESS)
NTI (DMS 100, 250)
USA NI-1
Note 2
USA NI-2
Not used
07 Sending method of calling number 
from/to network (for CIR/911 
Sender card)0
1
3
7Caller ID (SM)
T1-ANI
Enhanced 911
MFC-R2
09 Idle Code on ISDN B Channels
(DTI Reset)0
1Send 7F to PSTN
Send FF to PSTN
STSLOT NUMBER
(04-15)DEDATA
(1-2 digits)EXE
~
[CMAA] DTI/DCH/CIR Card Functions 
						

							ND-45669 (E) CHAPTER 3
Pag e 3 25
Revision 2.0
CMAC
COMMAND CODE
TITLE:
ISDN FUNCTIONS
AC
INITIAL
4. DATA TABLE:
1. FUNCTION:
This command assigns the functions to the ICH/BRI card.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
 + ACYY +   +   +  +   +   + 
 + ACYY +   +   +  +   +   +  + 
: Initial Data
YY SETTING DATA
RELATED 
COMMAND
No. MEANING DATA MEANING
00 Assignment of the ISDN Circuit Sta-
tion Number to be controlledX
XXXXISDN Circuit Station No.
01 Assignment of the Layer 2 data link 0
1Point to Point Connection
Point to Multipoint Connection
02 Assignment of the TEI (Terminal 
Endpoint Identifier)0
1Manual TEI Assignment
Automatic TEI Assignment
03 Assignment of Passive Bus in the 
point to multipoints connection0
1Extended Passive Bus
Short Distance Passive Bus
04 Assignment of the Layer 1 activation 0
1Always active
Activated by call event
06 Checking of the TEI (Terminal End-
point Identifier) when the Layer 2 
data link is released0
1Not provided
To provide
10 NI-1 mode 0
1To provide
Not provided
30 Assignment of SPID (Service Profile 
ID) for each BCH of BRI cardXX···XX
(8 digits)XXXX
 XXXX
SPID
ISDN
Subscriber’s No.
STDEICH No.
(00-11)ISDN CIRCUIT No.
(0-7)DEDATA
(1-4 digits)EXE
STDEAP No.
(04-15)BCH No.
(0/1)DEISDN
(4 digits) SUBSCRIBER’S No.SPID
(4 digits)EXE
~
[CMAC] ISDN Functions 
						

							CHAPTER 3 ND-45669 (E)
Page 326 Addendum-001
Revision 2.1 AUGUST, 1998
CMAD
COMMAND CODE
TITLE:
ZT CALLING AREA/PAD DATA ASSIGNMENT
AD
4 . D ATA  TA B L E :
1. FUNCTION:
This command assigns the calling area and PAD data for each ZT.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
 + ADYY +   +   +   +   + 
: Initial Data
YY MEANING ZT No.SETTING DATA
DATA MEANING
00 Calling Area 000-255 XX
 X XX
Group ZT No. (00 – 31)
Group No. (0 – 7)
Calling Area No. (00 –31)
01 PAD Data
(CSI-COT/ODT/DID)PA D
00
01
02
03
04
05
06
07
08
09
10
11
12
15Transmitter/Receiver PAD (dB)
+: Gain
-: Loss
0/0
0/+3
0/+6
0/-3
+3/+3
+3/+6
+3/-3
-3/-3
+3/0
+6/0
-3/0
-3/0
0/-3
0/0 08 PAD Data
(CSI-DTI)
09 PAD Data (CSI-LC/DLC) 00-12
15Same as YY = 01, 08
0/+6
10 PAD Data (CSI-CSI)
19 ZT Type 00
15D
term PS II Type
Former Dterm PS Type
STDEZT NUMBER
(3 digits)DESETTING DATA
(2-5 digits)EXE
[CMAD] ZT Calling Area/Pad Data Assignment 
						

							ND-45669 (E) CHAPTER 3
Addendum-001 Page 327
AUGUST, 1998 Revision 2.1
CMAE
COMMAND CODE
TITLE:
ZT OPERATION DATA ASSIGNMENT
AE
4. DATA TABLE:
1. FUNCTION:
This command is used for assigning the ZT Operation data.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
YY MEANING1S T DATA S E TT ING  DATA
DATA MEANING DATA MEANING
00 Nation Code 03 Nation Code Assign-
ment003
004
005
006
007
008
009
255North America 310
North America 311
North America 312
North America 313
North America 314
North America 315
North America 316
Not used
Home PBX ID 04 Assignment of Home 
PBX IDX-XXXXXXX
NONEHome PBX ID (1-7 
digits, Decimal)
Note 3
10 ZT Operation 
Mode00 – 31 Calling Area No. 15 Normal Mode
15 Control Carrier 
Information00 Control Carrier
Priority Assignment
Note 1
Note 2XX
 XX XX 00 00
 ab  c
a : 1st Priority
b : 2nd Priority
c : 3rd PriorityControl Carrier 
No. 01 – 06 
01 : 1920.35 MHz
02 : 1920.65 MHz
03 : 1920.95 MHz
04 : 1921.55 MHz
05 : 1921.85 MHz
06 : 1922.15 MHz
Note 1:Be sure to set from the 1st digit to last digit (10 digits). Last 4 digits must be set as “0000”.
Note 2:After changing this data, download the PS operation data by CM1D YY=20.
Note 3:Assign the same number with the first seven digits of the Individual PS number set by CM1D YY=00.
STDEDEEXE
++AEYY + + + +SETTING DATA 1ST DATA
(2 digits) (2-10 digits)
[CMAE] ZT Operation Data Assignment 
						

							CHAPTER 3 ND-45669 (E)
Page 327-1 Addendum-001
Revision 2.1 AUGUST, 1998
CMAE
COMMAND CODE
TITLE:
ZT OPERATION DATA ASSIGNMENT
AE
: Initial Data
YY MEANING1S T DATA S E TT ING  DATA
DATA MEANING DATA MEANING
42 Network ID (for 
Roaming Service)00 Network ID Assign-
ment00000-65534
NONENetwork ID
INITIAL 
						

							ND-45669 (E) CHAPTER 3
Addendum-002 Page 327-2
JANUARY, 1999 Revision 2.2
CMAF
COMMAND CODE
TITLE:
VISITOR PS DATA ASSIGNMENT
AF
MAT
4. DATA TABLE:
1. FUNCTION:
This command assigns the Visitor PS data.
2. PRECAUTION:
This data setting is valid when DBM (AP00) card is online.
3. ASSIGNMENT PROCEDURE:
: Initial Data
Y Y Y 1S T DATA 2ND DATA
No. MEANING DATA MEANING DATA MEANING
000 Assignment of Home 
PBX ID for Visitor PSX-XXXXXXX Home PBX ID
(1-7 digits, Decimal)000-255
CCC
NONEData Table No. 000-255
Data clear
No data
001 Route Selection Pattern 
Assignment for Visitor 
PS000-255 Data Table No.
Assigned by CMAF
YYY=00000-07
CCC
NONERoute Selection Pattern 
No. 00-07
Data clear
No data
002 Trunk Restriction Class 
in Day, Night Mode for 
Visitor PS000-255 Data Table No.
Assigned by CMAF 
YYY=00001
02
03
04
05
06
07
08
NONEUnrestricted (RCA)
Nonrestricted 1 (RCB)
Nonrestricted 2 (RCC)
Semirestricted 1 (RCD)
Semirestricted 2 (RCE)
Restricted 1 (RCF)
Restricted 2 (RCG)
Fully Restricted (RCH)
Not used
100
107Trunk Route Selection 
for location registration 
of Visitor PS1
4First Selected Route
Fourth Selected Route00-63
CCC
NONEQ-931a D Channel 
Trunk Route No.
Data clear
No data
200 Trunk Route for origi-
nating/terminating calls 
from/to Visitor PS1 First Selected Route 00-63
NONETrunk Route No. 00-63
No data
STDEDEEXE
++AFYYY + + + +2ND DATA 1ST DATA
(1-7 digits) (1-5 digits)
~
~
~ 
						

							CHAPTER 3 ND-45669 (E)
Page 327-3 Addendum-001
Revision 2.1 AUGUST, 1998
CMAF
COMMAND CODE
TITLE:
VISITOR PS DATA ASSIGNMENT
AF
MAT
208 Route Selection Pattern 
Number for the Trunk 
Restriction Class sent 
from the Home PBX00
15Trunk Restriction Class 
sent from Home PBX
01: Unrestricted (RCA)
02: Nonrestricted 1 (RCB)
03: Nonrestricted 2 (RCC)
04: Semirestricted 1/2 
(RCD/RCE)
05: Restricted 1/2 (RCF/
RCG)
06: Fully restricted (RCH)
07-15 Not used00 Route Selection Pattern 
00
210 Roaming Station
Number00 X-XXXX Roaming Station No.
998 Work Memory All 
Clear of DBM Card1 All Clear CCC Data clear
999 System Data Memory 
All Clear of DBM Card1 All Clear CCC Data clear
: Initial Data
Y Y Y 1S T DATA 2ND DATA
No. MEANING DATA MEANING DATA MEANING
~ 
						

							THIS PAGE INTENTIONALLY LEFT BLANK.
ND-45669 (E) CHAPTER 3
Addendum-001 Page 327-4
AUGUST, 1998 Revision 2.1
This page is for your notes.