NEC Neax2000 Ivs Command Manual

							CHAPTER 3 ND-45669 (E)
Page 348 Addendum-002
Revision 2.2 JANUARY, 1999
CME5
COMMAND CODE
TITLE:
STATION, TRUNK LINE MAKE BUSY
E5
4. DATA TABLE:
Note 1:For a station that is made busy, call termination to the station is restricted, but Call origination is available.
For extension lines on a Multiline Terminal, My Line and Multiline make busy can be set individually, with
the same condition as mentioned above.
Note 2:For a trunk that is made busy, the outgoing call is restricted, but on incoming, the call is available.
Note 3:For the B channel that is made busy, call termination to the ISDN Terminal corresponds with the B channel
is restricted, but call origination is available.
Note 4:Under a made busy condition, the Busy Lamp on the card flashes (60 IPM).
Note 5:Make idle of ZT since the ZT is in make busy forcibly when assigning the ZT data by CM10.
1. FUNCTION:
This command is used to make busy any station or trunk in the software.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
YSTATION TRUNK NUMBER SETTING DATA
REMARKS
No. MEANING DATA MEANING
0X
XXXXStation number
(1-4 digits)
Note 10
1Make Busy set
In serviceFor LC, AUC, and 
DLC card
1 000
255Trunk number
Note 20
1Make Busy set
In serviceFor COT, LDT, 
ODT, 2BRT, and 
AUC card
2 XXXX
X
ISDN Circuit Station No.
0: B1 Channel
1: B2 Channel
Note 30
1Make busy set
In serviceFor ILC card
3 000
255ZT number 0
1
2Make busy (forced)
Make idle
Make busy
(after calls finished)For ZT
Note 5
STDEDEEXE
++E5Y + + + +
(0/1) D ATA
NUMBER STATION/TRUNK
~ ~
~
, 
						

							ND-45669 (E) CHAPTER 3
Addendum-002 Page 349
JANUARY, 1999 Revision 2.2
CME6
COMMAND CODE
TITLE:
CALL FORWARDING SET/RESET FROM MAT/CAT
E6
4. DATA TABLE:
Note:To reset Call Forwarding, assign “CCC” to the second data.
1. FUNCTION:
This command sets/resets the Call Forwarding service to each station from a MAT/CAT.
2. PRECAUTION:
CME6 can be used for any station irrespective of its state.
3. ASSIGNMENT PROCEDURE:
 + E6YY +   +  +   +   + 
YY MEANING DESTINATION No.
00 Call Forwarding-All Calls • Destination = Extension;
X-XXXX: Station No. (1-4 digits)
• Destination = Outside party;
X-XX
+,+YY...YY
Called No. (Max. 26 digits)
Separator Mark
Outgoing Trunk/LCR Group Access Code (1-2 
digits)
• Destination = Attendant; E000 01 Call Forwarding-Busy Line
02 Call Forwarding-No Answer
03 Call Forwarding-Busy Line/
No Answer
04 Split Call Forwarding-All Calls 0: Target station for Split Call Forwarding (Block 0)/ATT
1: Target station for Split Call Forwarding (Block 1)
2: Target station for Split Call Forwarding (Block 2)
3: Target station for Split Call Forwarding (Block 3)
4: Target station for Split Call Forwarding (Block 4)
05 Split Call Forwarding-Busy Line/No 
Answer5: Target station for Split Call Forwarding (Block 5)
6: Target station for Split Call Forwarding (Block 6)
7: Target station for Split Call Forwarding (Block 7)
8: Target station for Call Forwarding
9: Station Speed Dialing (Block 0)
STDESTATION No.
(1-4 digits)DEDESTINATION No.
(1-26 digits)CCC
(for reset)EXE
[CME6] Call Forwarding Set/Reset From MAT/CAT 
						

							CHAPTER 3 ND-45669 (E)
Pag e 3 50
Revision 2.0
CME7
COMMAND CODE
TITLE:
PASSWORD LEVEL
E7
4. DATA TABLE:
Note:In case of YY = 20, 21, the data to be set is “1” only.
1. FUNCTION:
This command specifies the accessible commands for each Password Level.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
YY
COMMAND CODE SETTING DATA
No. PASSWORD LEVEL
00
01
02
03
04
05
06
10
11
12
13
14
15
16Password Level 0 – 6
1 – 6
2 – 6
3 – 6
4 – 6
5 – 6
6
0
1
2
3
4
5
6XX: 00 – FF
(Exclusive of 03, E7, E9)0: Allowed
1:
  Restricted
20 To clear all the Password Level 
settings for individual commandsXX: 00 – FF
(Exclusive of 03, E7, E9)1: All Password Levels exclud-
ing Level 7 are restricted from 
assignment of designated 
command.
21 To clear all the Password Level 
settings for all commandsXX: 00 1: All Password Levels exclud-
ing Level 7 are restricted 
from assignment of all com-
mands.
ST  +  E7YY  +  DE  +COMMAND CODE
(2 digits)+  DE   +D ATA
(1 digit)+  EXE
[CME7] Password Level 
						

							ND-45669 (E) CHAPTER 3
Pag e 3 51
Revision 2.0
CME9
COMMAND CODE
TITLE:
PASSWORD CODE
E9
MAT
4. DATA TABLE:
Note:Password Level 7 can access all the commands.
1. FUNCTION:
This command is used to define the Password Code of each Password Level and the availability of Pass-
word Service.
2. PRECAUTION:
(1) Before setting the Password code, Function Number 8 (Change of Password) must be set to 0
(Allowed).
(2) When programming a Password Code, the Password Code for Password Level 7 must be made. If
no Password Code of Password Level 7 is set, the programming of Password Service provision
(CME9, FUNCTION No. 9) is restricted with the message “CODE NOT USED”. 
Note
(3) Function No. 9 (Password Service) must be set to 0 (Provided) after programming of all Password
Codes is completed.
3. ASSIGNMENT PROCEDURE:
: Initial Data
PASSWORD LEVEL No. /
FUNCTION No.SETTING DATA
REMARKS
DATA MEANING
0
7Password Level 0
Password Level 7X
XX
X . . . X
(Max. 8 digits)Password Code Following Password Codes are 
not available:
“CC . . . C” (All “C”)
“FF . . . F” (All “F”)
8 Change of Password
(Display of Password)0 
1
 
Allowed
Restricted
9Password Service 0
1
 
Provided
Not provided
ST  +  E9  +  DE  +PASSWORD LEVEL NO.
/FUNCTION NO.
(1 digit)+  DE  +  DATA  +  EXE
~~
~
[CME9] Password Code 
						

							CHAPTER 3  ND-45669  (E)
C M EA
M AT
1.  FUN CTIO N:
ST  +   E AY   +   DE  +
[ C M EA ]  Fau lt  I nf orm ation  Store /D isp lay F unct io n s 
						

							ND-45669  (E)   CHAPTER 3
CM EA
MAT
: I n it ial Data
~ 
						

							CHAPTER 3  ND-45669  (E)
C M EA
M AT
2  Regis tr atio n  of  fau lt 
~ 
						

							ND-45669 (E) CHAPTER 3
Pag e 3 55
Revision 2.0
CMEA
COMMAND CODE
TITLE:
FAULT INFORMATION STORE/DISPLAY FUNCTIONS
EA
MAT
n  
Fault Information Display
After the following operation:
              
The first screen displays on the MAT/CAT. The fault information is separated into four separate parts,
and displayed on four screens. An example of fault information display is provided below:
EXPLANATION OF SCREEN INFORMATION
1: Fault Occurrence Kind No./Fault Restoration Kind No.
FAULT KIND 
NUMBERFAULT CONTENT
01 System initialized
03 The number of stack entries was more than the caution level 
04 MP-FP/AP communication failure 
08 FP-AP card down
09 Power failure 
20 DTI line failure 
21 DCH D-channel link connection failure 
22 CCH link connection
25 The number of lockout stations was more than the predetermined number 
26 DLC card down
STDEDE
EA0 00 ++++
1st Screen2nd Screen
4th Screen3rd Screen
DE
DEDE 1 : 03 MN MP    00
12 3
91011124
5678 3 : xx xx xx xx 2 : 93/3/20 20 : 31
3 : xx xx xx xx
to 1st screen of next data 
						

							CHAPTER 3 ND-45669 (E)
Pag e 3 56
Revision 2.0
CMEA
COMMAND CODE
TITLE:
FAULT INFORMATION STORE/DISPLAY FUNCTIONS
EA
MAT
EXPLANATION OF SCREEN INFORMATION (Continued)
2: External Alarm Kind (MJ/MN/-)
Use of External Alarm Kind - Minor (MN), Major (MJ) or external alarm is not provided (-) can be
programmed by CMEA Y=2. The following table shows the standard data set by the 2nd data = 3 of
CMEA Y=2.
FAULT RESTORATION 
KIND NUMBERFAULT RESTORATION CONTENT
18 FP/AP package returned to normal condition
19 Power failure returned to normal condition
30 DTI line returned to normal condition
31 DCH D-channel link connection returned to the normal condition
32 CCH link connection returned to normal condition
35 The number of lockout stations was less than the predetermined number
36 DLC card returned to normal condition
FAULT KIND 
(1ST)CONTENT ALARM KIND
01 System Initialized MN ALARM
03 The number of stack entries was more than the caution level MN ALARM
04 MP-FP/AP communication failure  MN ALARM
08 FP/AP package down MN ALARM
09 Power failure MN ALARM
18 FP/AP package returned to normal condition  -- 
19 Power failure returned to normal condition  -- 
20 DTI line failure  MN ALARM
21 DCH D-channel link connection failure  MN ALARM
22 CCH link connection failure MN ALARM
25 The number of lockout stations was more than the predetermind number 
(Refer to CM42, 1ST data = 01) MN ALARM 
(Fixed)
26 DLC card down -- 
30 DTI line returned to normal condition  -- 
31 DCH D-channel link connection returned to the normal condition  -- 
32 CCH link connection returned to normal condition  -- 
35 The number of lockout stations was less than the predetermined number  -- 
36 DLC card returned to normal condition  --  
						

							ND-45669 (E) CHAPTER 3
Pag e 3 57
Revision 2.0
CMEA
COMMAND CODE
TITLE:
FAULT INFORMATION STORE/DISPLAY FUNCTIONS
EA
MAT
EXPLANATION OF SCREEN INFORMATION (Continued)
3: 
CPU Kind and FP/AP number for which a fault was detected
4:  Date and Time of Fault Occurrence and Restoration
5-12: Fault-Related Information/Fault Restoration-Related Information
INDICATION MEANING
MP 00 MP
FP 00 - 03 FP Number 0 - 3
AP 04 - 15 AP Card Number 4 - 15
FAU LT  
KIND 
NUMBER56789101112
01 Initial 
Kind, etc 
1 ,  2System Initialization-related information
3
03 Stack Kind 
4
04 Communi-
cation Fail-
ure Kind
5
08 FP/AP 
Number 6
09 Power Fail-
ure Kind 1
7Power Fail-
ure Kind 2
 7Power Fail-
ure Kind 3
7
20 Fault Detail 
Kind 9
21 D-channel 
circuit No. 
10
22 CCH No. 
11
25
26 DLC Fail-
ure KindLEN Station Number 
1413
12