Konica Minolta bizhub 500 User Manual

							3Specifying Settings From the Control Panel
3-126 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
v3 Setting
The settings that can be specified are described below.
SNMP v3 Setting screen 1/3
SNMP v3 Read Setting screen 2/3
SNMP v3 Write Setting screen 3/3
ItemDescription
Context Name Specify the context name. Use the keyboard that appears 
in the touch panel to type in the context name (up to 63 
characters).
Discovery User Select whether to enable the Discovery User setting.
Discovery User Name Specify the discovery user name. Use the keyboard that 
appears in the touch panel to type in the discovery user 
name (up to 32 characters).
ItemDescription
Read  User  Name Specify the read user name. Use the keyboard that appears 
in the touch panel to type in the read user name (up to 32 
characters).
Security Level Select the authentication security level.
Read User Password Specify the authentication password. Use the keyboard 
that appears in the touch panel to enter each password for 
the security level (up to 32 characters).
If “auth-password” is selected, enter the password only in 
auth-password.
If “priv-password” is selected, enter both passwords.
ItemDescription
Write User Name Specify the write user name. Use the keyboard that ap-
pears in the touch panel to type in the write user name (up 
to 32 characters).
Security Level Select the authentication security level.
Write User Password Specify the authentication password. Use the keyboard 
that appears in the touch panel to enter each password for 
the security level (up to 32 characters). 
If “auth-password” is selected, enter the password only in 
auth-password.
If “priv-password” is selected, enter both passwords.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-127
Specifying Settings From the Control Panel
Chapter 3
To specify the v3 settings
1In the Network Setting screen, touch [v3 Setting].
SNMP v3 Setting screen 1/3 appears.
2Specify the desired settings.
3Touch [Fwd.→].
SNMP v3 Setting screen 2/3 appears.
4Specify the desired settings.
5Touch [Fwd.→].
SNMP v3 Setting screen 3/3 appears.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-128 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
6Specify the desired settings.
7Touch [OK].
The SNMP Setting screen appears again.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-129
Specifying Settings From the Control Panel
Chapter 3
3.33 Bonjour Setting
You can specify the Bonjour setting.
Bonjour Setting screen
To specify the Bonjour settings
1In the Administrator Setting screen, touch [5 Network Setting].
2In the Network Setting screen, touch [Fwd.→], and then touch [2 Bon-
jour Setting].
The Bonjour Setting screen appears.
3Specify the desired settings.
4Touch [OK].
ItemDescription
Bonjour  Setting Select whether to enable the Bonjour setting. If “OFF” is se-
lected under “TCP Socket Setting”, some of the programs 
on your computer may not be usable.
Bonjour Name Specify the name that is used for the Bonjour setting. Use 
the keyboard that appears in the touch panel to type in the 
name (up to 63 characters).
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-130 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
2
Note 
To display the Administrator Setting screen, refer to “To display the Ad-
ministrator Setting screen” on page 3-8.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-131
Specifying Settings From the Control Panel
Chapter 3
3.34 TCP Socket Setting
You can specify the TCP socket settings. The TCP socket is used for the 
computer programs and the data transmission of this machine.
The settings that can be specified are described below.
TCP Socket Setting screen 1/2
TCP Socket Setting screen 2/2
To specify the TCP socket settings
1In the Administrator Setting screen, touch [5 Network Setting].
2In the Network Setting screen, touch [Fwd.→], and then touch [3 TCP 
Socket Setting].
TCP Socket Setting screen 1/2 appears.
3Specify the desired settings.
ItemDescription
TCP Socket Setting Select whether to use the TCP socket setting. If “OFF” is 
selected under “TCP Socket Setting”, some of the pro-
grams on your computer may not be usable.
Port Number Specify the port number that is used. To change the value, 
press the [C] (clear) key, and then use the keypad to type in 
the value (between 1 and 65535).
ItemDescription
TCP Socket (ASCII Mode) Select whether to use the TCP Socket (ASCII Mode) set-
ting.
Port Number (ASCII Mode) Specify the port number that is used with the ASCII mode. 
To change the value, press the [C] (clear) key, and then use 
the keypad to type in the value (between 1 and 65535).
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-132 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
4Touch [Fwd.→].
TCP Socket Setting screen 2/2 appears.
5Specify the desired settings.
6Touch [OK].
2
Note 
To display the Administrator Setting screen, refer to “To display the Ad-
ministrator Setting screen” on page 3-8.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears.
When a certificate is set to “Enable” on this machine, the [SSL Setting] or 
[Port Number (SSL)] screen appears. To perform SSL transmission, spec-
ify the settings.
To perform external server authentication on this machine, the TCP sock-
et SSL settings are required to access this machine from the application 
that is using the TCP socket.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-133
Specifying Settings From the Control Panel
Chapter 3
3.35 OpenAPI Settings
Specify whether or not interface is open to software with a function for com-
municating with the copier. The settings for “Access Setting”, “Port No.”, 
“SSL”, and “Authentication” of OpenAPI can be changed.
Access Setting
Sets whether to permit access from other systems that use OpenAPI. (De-
fault setting: Allow)
1In the Administrator Setting screen, touch [System Connection]. (Refer 
to page 3-8 for more details.)
2In the System Connection screen, touch [1 OpenAPI Setting].
3In the OpenAPI Setting screen, touch [Access Setting].
Buttons for selecting settings appear.
4Touch the desired selection key.
– To permit access using OpenAPI, touch [Allow].
– To prohibit access using OpenAPI, touch [Restrict].
Access using OpenAPI is set to be permitted or prohibited.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-134 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
Port No.
Specify the port number that other systems access using OpenAPI (initial 
port number: 50001, initial port number (SSL): 50003).
1In the Administrator Setting screen, touch [System Connection]. (Refer 
to page 3-8 for more details.)
2In the System Connection screen, touch [1 OpenAPI Setting].
3In the OpenAPI Setting screen, touch [Port No.].
The OpenAPI Port Setting screen appears.
4Press the [C] (clear) key to erase the value, and then use the keypad to 
type in the value (between 1 and 65535).
– If a value outside of the allowable range is specified, the message 
“Input Error” appears. Type in a value within the allowable range.
5Touch [OK].
– To cancel changes to the setting, touch [Cancel].
The port number that other systems access using OpenAPI is set.
2
Note 
If the port number for SSL communication is specified, the certificate 
must be pre-installed from PageScope Web Connection. For details, re-
fer to “SSL/TLS” on page 4-104.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-135
Specifying Settings From the Control Panel
Chapter 3
SSL
Specify whether to encrypt with SSL access from other systems that use 
OpenAPI. (Default setting: OFF)
1In the Administrator Setting screen, touch [System Connection]. (Refer 
to page 3-8 for more details.)
2In the System Connection screen, touch [1 OpenAPI Setting].
3In the OpenAPI Setting screen, touch [SSL].
4Touch the desired key.
SSL encryption is enabled or disabled.
2
Note 
To use SSL, a certificate must be issued from PageScope Web Connec-
tion in advance. For details, see “SSL/TLS” on page 4-104.
Downloaded From ManualsPrinter.com Manuals