Konica Minolta bizhub 500 User Manual

							3Specifying Settings From the Control Panel
3-66 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
3.15 FTP Settings
Settings for sending scan data to FTP servers can be specified.
FTP Parameters
The FTP parameters are as follows:
FTP Setting screen 1/3
FTP Setting screen 2/3
FTP Setting screen 3/3
ItemDescription
Proxy Server Address Sets the proxy server address. Use the keypad in the 
control panel to type in the address.
Proxy Port Number Sets the port number of the proxy server. To change the 
value, press the [C] (clear) key, and then use the keypad to 
type in the value (between 1 and 65535).
ItemDescription
Port No. Set the port number used to communicate with the FTP 
server. To change the value, press the [C] (clear) key, and 
then use the keypad to type in the value (between 1 and 
65535).
Connection Timeout If the transmission stops while uploading data to the FTP 
server, the upload operation is automatically aborted after 
a specified time elapses. Set the time from the point when 
the transmission stops to the point when the upload 
operation is to be aborted. To change the value, press the 
[C] (clear) key, and then use the keypad to type in the value 
(between 5 and 300 seconds).
ItemDescription
FTP Client Sets whether to use the Scan to FTP operation.
FTP Server Specify whether to use this machine as an FTP server. 
When using the copier as an FTP server, select “ON”. When 
using an application that links to the copier as an FTP client 
of the copier, “ON” must be selected.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-67
Specifying Settings From the Control Panel
Chapter 3
To specify FTP settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [5 FTP Setting].
FTP Setting screen 1/3 appears.
3Specify the desired settings.
4Touch [Fwd.→].
FTP Setting screen 2/3 appears.
5Specify the desired settings.
6Touch [Fwd.→].
FTP Setting screen 3/3 appears.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-68 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
7Specify the desired settings.
8Touch [OK].
The FTP settings are applied.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area. Otherwise, cancel the Utility mode by touching [Close] in each 
screen until the screen for the Copy, Fax, Scan or Box mode appears.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-69
Specifying Settings From the Control Panel
Chapter 3
3.16 SMB Settings
You can specify the settings for sharing printers and sending files over a net-
work.
SMB Parameters
The SMB parameters are as follows:
SMB Setting screen 1/4
WINS Setting screen 2/4
WINS Setting screen 3/4
Client Setting screen 4/4
ItemDescription
Print Setting Specifies whether to use the SMB port in Print mode.
NetBIOS Name Sets the NetBIOS name. Use the keyboard that appears in 
the touch panel to type in the NetBIOS name (up to 15 
characters).
Print Service Name Sets the printer service name. Use the keyboard that 
appears in the touch panel to type in the print service name 
(up to 12 characters).
Workgroup Sets the work group. Use the keyboard that appears in the 
touch panel to type in the workgroup name (up to 15 
characters).
ItemDescription
WINS Setting Select whether to use the WINS function.
Auto Obtain Setting Select whether to automatically acquire the IP address of 
the WINS server from the DHCP server.
ItemDescription
WINS Server Address1-2 Specify the IP address of the WINS server.
ItemDescription
User Authentication (NTLM) Select whether to use the user authentication with NTLM.
SMB TX Setting Select whether to use the SMB transmission setting.
NTLM Select the NTLM version to be used.
Select [v1/v2] or [v1] when using a computer over a network 
that is running a Windows 98 SE or Windows Me operating 
system.
Select [v1] when the Samba service is operating a server 
over a network.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-70 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
2
Note 
When performing SMB scans (host name setting) via a router, specify the 
WINS settings according to the SMB transmission settings.
To specify SMB settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [6 SMB Setting].
The SMB Setting screen (1/4) appears.
3Specify the desired settings.
4Touch [Fwd.→].
SMB Setting screen 2/4 appears.
5Specify the desired settings.
6Touch [Fwd.→].
SMB Setting screen 3/4 appears.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-71
Specifying Settings From the Control Panel
Chapter 3
7Specify the desired settings.
8Touch [Fwd.→].
SMB Setting screen 4/4 appears.
9Specify the desired settings.
10Touch [OK].
The SMB settings are applied.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-72 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-73
Specifying Settings From the Control Panel
Chapter 3
3.17 AppleTalk Settings
You can specify the settings for network printing using AppleTalk.
AppleTalk Parameters
The AppleTalk parameters are as follows:
To specify AppleTalk settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [7 AppleTalk Setting].
The AppleTalk Setting screen appears.
3Specify the desired settings.
ItemDescription
AppleTalk Setting Specify whether to turn on the AppleTalk settings.
Printer Name Sets the name of this machine that appears on the 
AppleTalk network. Use the keyboard that appears in the 
touch panel to type in the name (up to 31 characters).
Zone Name Sets the name of the zone to which the machine is to be 
connected. Use the keyboard that appears in the touch 
panel to type in the zone name (up to 31 characters).
Current Zone Displays the current zone.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-74 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
4Touch [OK].
The AppleTalk settings are applied.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-75
Specifying Settings From the Control Panel
Chapter 3
3.18 Enabling LDAP Settings
The LDAP function to which the machine can connect and search and re-
trieve information can be enabled/disabled. 
Enabling LDAP Parameters
The Enabling LDAP parameters are as follows:
To specify Enabling LDAP settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [8 LDAP Setting].
3In the LDAP Setting screen, touch [1 Enabling LDAP].
The Enabling LDAP screen appears.
4Specify the desired settings.
5Touch [OK].
The LDAP function is set.
ItemDescription
LDAP Function Set whether or not to use the LDAP function.
Downloaded From ManualsPrinter.com Manuals