Konica Minolta bizhub 500 User Manual

							3Specifying Settings From the Control Panel
3-76 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area. Otherwise, cancel the Utility mode by touching [Close] in each 
screen until the screen for the Copy, Fax, Scan or Box mode appears.
2
Reminder 
If the LDAP server settings are not specified correctly, network failure 
may occur. The server administrator should specify LDAP settings.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-77
Specifying Settings From the Control Panel
Chapter 3
3.19 Setting Up LDAP Settings
The LDAP server can be registered and authentication settings can be spec-
ified.
LDAP Server Registration Parameters
The LDAP server registration parameters are as follows:
Setting Up LDAP screen 1/6
Setting Up LDAP screen 2/6
* When [LDAP Function] is set to “ON” on the Enabling LDAP screen, the [Check Connection] key 
is displayed only when [Manual Destination Input] is set to “Allow” on the Security Details 
screen.
ItemDescription
LDAP Server Name Set the LDAP server name to be registered. Use the key-
board that appears in the touch panel to type in the server 
name (up to 32 characters).
Max. Search Results Set the maximum number of destinations to display after 
searching. To change the value, press the [C] (clear) key, 
and then use the keypad to type in the value (between 5 
and 1000 destinations).
Timeout Set the maximum wait time for the search operation. To 
change the value, press the [C] (clear) key, and then use the 
keypad to type in the value (between 5 and 300 seconds).
Initial Setting for Search Details Specify the initial setting of the search conditions when 
performing a detailed search. For details on specifying the 
setting, refer to “Initial Setting for Search Details” on 
page 3-84.
Check Connection Checks the connection to the LDAP server.
Reset All Settings The LDAP server settings can be reset to the default set-
tings that were specified at the factory.
When a reset confirmation message appears, touch [Yes].
ItemDescription
Server Address Sets the IP address of the LDAP server. Use the keyboard 
that appears in the touch panel to type in the address (up 
to 255 characters).
Search Base Specify the search starting point in the hierarchical 
structure that is arranged in the LDAP server. Searchers are 
performed by also including the lower sub-directories from 
the starting point that was specified. Use the keyboard that 
appears in the touch panel to type in the address (up to 255 
characters).
Check Connection* Checks the connection to the LDAP server.
Reset All Settings The LDAP server settings can be reset to their factory 
default.
When a reset confirmation message appears, touch [Yes].
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-78 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
Setting Up LDAP screen 3/6
Setting Up LDAP screen 4/6
Setting Up LDAP screen 5/6
ItemDescription
Enable SSL Sets whether to use SSL (data encryption) when 
connecting to the LDAP server. When SSL is used, the 
content that is sent is encrypted.
Port No. Sets the port number of the LDAP server. To change the 
value, press the [C] (clear) key, and then use the keypad to 
type in the value (between 1 and 65535).
Port Number (SSL) Specify the port number for using SSL. To change the 
value, press the [C] (clear) key, and then use the keypad to 
type in the value (between 1 and 65535).
Check Connection Checks the connection to the LDAP server.
Reset All Settings The LDAP server settings can be reset to their factory 
default.
When a reset confirmation message appears, touch [Yes].
ItemDescription
Authentication Method Select the authentication method used when logging on to 
the LDAP server.
[anonymous]: An authentication method that does not re-
quire the user name and password Is specified to [anony-
mous], dynamic authentication is disabled.
[Simple] : A simple authentication method that requires the 
user name and password. Take caution since the pass-
words can be leaked over the network.
[Digest-MD5]: An authentication method that can be used 
on a typical LDAP server. If authentication fails using Di-
gest-MD5, the authentication is performed by automatical-
ly switching to CRAM-MD5.
[GSS-SPNEGO]: An authentication method that can be 
used with Active Directory in Windows (Kerberos authenti-
cation).
[NTLM v1] and [NTLM v2]: Standard authentication meth-
ods that can be used with Windows NT. Used for logging 
on when sharing files and printers.
ItemDescription
Select Server Authentication 
MethodSelect the method to be used during server authentication.
[Use The Setting Value]: Authenticates the settings speci-
fied in Setting Up LDAP screen 6/6.
[User Authentication]: Requires a user name and password 
when using the LDAP search function. When logging on to 
the copier with the external server authentication function, 
the user name that was used when performing the external 
server authentication is automatically entered in the LDAP 
server login screen. The user name can also be changed.
[Dynamic Authentication]: Requires a user name and pass-
word when using the LDAP search function.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-79
Specifying Settings From the Control Panel
Chapter 3
Setting Up LDAP screen 6/6
Use referral Select whether to use the referral setting. When referral is 
used, the search base that was specified in LDAP Sever 
Setting searches the top and bottom levels as the starting 
point.
ItemDescription
ItemDescription
Login Name Sets the login name used to connect to the LDAP server. 
Use the keyboard that appears in the touch panel to type in 
the name (up to 255 characters).
Password Sets the password used to connect to the LDAP server. 
Use the keyboard that appears in the touch panel to type in 
the password (up to 128 characters).
Domain Name Sets the domain name used to connect to the LDAP server 
as necessary. Use the keyboard that appears in the touch 
panel to type in the name (up to 64 characters).
Check Connection Checks the connection to the LDAP server.
Reset All Settings The LDAP server settings can be reset to their factory 
default.
When a reset confirmation message appears, touch [Yes].
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-80 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
To specify Setting Up LDAP settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [8 LDAP Setting].
3In the LDAP Setting screen, touch [2 Setting Up LDAP].
4Touch the LDAP server button to register and specify the setting.
Setting Up LDAP screen 1/6 appears.
5Specify the desired settings.
6Touch [Fwd.→].
Setting Up LDAP screen 2/6 appears.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-81
Specifying Settings From the Control Panel
Chapter 3
7Specify the desired settings.
8Touch [Fwd.→].
Setting Up LDAP screen 3/6 appears.
9Specify the desired settings.
10Touch [Fwd.→].
Setting Up LDAP screen 4/6 appears.
11Specify the desired settings.
12Touch [Fwd.→].
Setting Up LDAP screen 5/6 appears.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-82 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
13Specify the desired setting.
14Touch [Fwd.→].
Setting Up LDAP screen 6/6 appears.
15Specify the desired settings.
16Touch [OK].
The LDAP server registration and authentication are set.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears.
2
Reminder 
If the LDAP server settings are not specified correctly, network failure 
may occur. The server administrator should specify LDAP settings.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-83
Specifying Settings From the Control Panel
Chapter 3
2
Note 
Be sure to use an authentication method like the one that is used by the 
LDAP server. For details, refer to the manual of the LDAP server being 
used.
If the authentication method is specified as “GSS-SPNEGO”, enter the 
domain name for “Active Directory”.
!
Detail 
Depending on the authentication method, settings for the following pa-
rameters must be set correctly on the Setting Up LDAP screen (6/6) in or-
der to perform the “Check Connection” operation.
For [Simple] and [DIGEST-MD5]: Login Name
For [GSS-SPNEGO]: Login Name and Domain Name
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-84 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
Initial Setting for Search Details
The initial setting of the search conditions when performing a detailed search 
can be specified by “Name”, “E-Mail”, “Fax Number”, “Last Name”, “First 
Name”, “City”, “Company Name”, and “Department”.
1On the Setting Up LDAP screen, touch [Initial Setting for Search De-
tails].
The Initial Setting for Search Details screen appears.
2Touch [Condition].
The Select Condition screen appears.
3Touch [OR], [AND], [Begins With], or [Ends With].
4Touch [OK].
– The initial setting that is specified in “Initial Setting for Search De-
tails” can be changed when the user uses the LDAP search.
The selected condition is set.
5Touch [OK].
The Setting Up LDAP screen appears again.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-85
Specifying Settings From the Control Panel
Chapter 3
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears.
Downloaded From ManualsPrinter.com Manuals