Konica Minolta bizhub 500 User Manual

							3Specifying Settings From the Control Panel
3-116 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
3.29 LPD Settings
The use of LPD when printing can be enabled or disabled.
To specify LPD settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [0 Detail Setting].
3In the Detail Setting screen, touch [7 LPD Setting].
The LPD Setting screen appears.
4Touch [Enable] or [Disable].
5Touch [OK].
The use of LPD is enabled or disabled.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-117
Specifying Settings From the Control Panel
Chapter 3
3.30 Prefix/Suffix Settings
The registered characters can be added to the e-mail address that is speci-
fied when sending e-mail. This eliminates having to enter characters that are 
often entered such as the same domain name.
Prefix/Suffix Parameters
The prefix/suffix parameters are as follows:
To specify the prefix/suffix settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [0 Detail Setting].
3In the Detail Setting screen, touch [8 Prefix/Suffix Setting].
The Prefix/Suffix Setting screen appears.
ItemDescription
ON/OFF Setting This parameter sets whether to enable the prefix/suffix 
function.
Prefix/Suffix Setting Registers the character strings that are used by the prefix/
suffix function. For details on specifying the settings, refer 
to “Prefix/Suffix Settings” on page 3-117.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-118 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
4Specify the desired settings.
The prefix/suffix is set.
If [ON] is selected, continue with the registration of prefixes/suffixes.
2
Note 
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-119
Specifying Settings From the Control Panel
Chapter 3
Prefix/Suffix Setting
The character strings that are used by the prefix/suffix input function can be 
registered.
1In the Prefix/Suffix Setting screen, touch [2 Prefix/Suffix Setting].
The Prefix/Suffix Setting screen appears.
2Touch [Prefix].
The Prefix screen appears.
3Enter the character string that is to be used as a prefix (up to 20 char-
acters).
– For the procedure to enter characters, refer to “Entering text” on 
page 6-5.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-120 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
4Touch [OK].
– To cancel changes to the setting, touch [Cancel].
The prefix is set.
5Touch [Suffix].
The Suffix screen appears.
6Enter the character string that is to be used as a suffix (up to 64 char-
acters).
– For the procedure to enter characters, refer to “Entering text” on 
page 6-5.
7Touch [OK].
– To cancel changes to the setting, touch [Cancel].
The suffix is set.
8Touch [Close].
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-121
Specifying Settings From the Control Panel
Chapter 3
3.31 Action for Invalid Certificate
When this machine is to be connected to an SSL server as a client, you can 
specify the operation method when the validation of the SSL server certifi-
cate has expired.
2
Note 
The functions that can be specified are described below. 
SMTP over SSL
POP over SSL
LDAP over SSL
To specify the Action for Invalid Certificate settings
1In the Administrator Setting screen, touch [5 Network Setting].
2In the Network Setting screen, touch [0 Detail Setting].
3In the Detail Setting screen, touch [9 Action for Invalid Certificate].
The Action for Invalid Certificate screen appears.
4Select the job process method when disabled.
5Touch [OK].
ItemDescription
Continue The job continues even when the validation of a server cer-
tification has expired.
Delete the Job The job is deleted when the validation of a server certifica-
tion has expired.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-122 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
2
Note 
To display the Administrator Setting screen, refer to “To display the Ad-
ministrator Setting screen” on page 3-8.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-123
Specifying Settings From the Control Panel
Chapter 3
3.32 SNMP Settings
SNMP settings can be specified.
SNMP Parameters
The SNMP parameters are as follows:
The v1/v2c settings that can be specified are described below.
ItemDescription
SNMP Setting Specify whether to use SNMP.
SNMP v1/v2c(IP) Select whether to use SNMP v1/v2c (IP).
SNMP v3(IP) Select whether to use SNMP v3 (IP).
SNMP v1(IPX) Select whether to use SNMP v1 (IPX).
UDP Port Number Specify the UDP port number. To change the value, press 
the [C] (clear) key, and then use the keypad to type in the 
value (between 1 and 65535).
[v1/v2c Setting] Specify when you want to select v1 or v2c. For details on 
specifying the setting, refer to “v1/v2c Setting” on 
page 3-125.
[v3 Setting] Specify when v3 is selected. For details on specifying the 
setting, refer to “v3 Setting” on page 3-126.
ItemDescription
Write Setting Specify whether to enable the write setting.
Read Community Name Specify the read community name. The default setting is 
“public”. Use the keyboard that appears in the touch panel 
to type in the read community name.
Write Community Name Specify the write community name. The default setting is 
“private”. Use the keyboard that appears in the touch panel 
to type in the write community name.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-124 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
To specify SNMP settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [Fwd.->], then [1 SNMP Setting].
3Specify the desired settings.
4Touch [OK].
The SNMP is set.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-125
Specifying Settings From the Control Panel
Chapter 3
v1/v2c Setting
1In the Network Setting screen, touch [v1/v2c Setting].
2Specify the settings for v1/v2c.
3Touch [OK].
The SNMP Setting screen appears again.
Downloaded From ManualsPrinter.com Manuals