Konica Minolta bizhub 500 User Manual

							3Specifying Settings From the Control Panel
3-46 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
3.12 TCP/IP Settings
The settings for using the machine on a TCP/IP network can be specified.
To activate all network setting changes, turn the main power off and then 
back on.
2
Reminder 
When turning the main power switch OFF then ON, wait for 10 seconds 
or longer before turning it ON again; otherwise the copier may not func-
tion normally.
Before Specifying the Settings
When specifying TCP/IP settings, note the following points.
-If “IP Address Setting Method” is set to “Auto Input”, “IP Address”, “Sub-
net Mask”, and “Default Gateway” are not available.
-When a DHCP server is used, the IP address, subnet mask, and default 
gateway are assigned from the DHCP server. Therefore, there is no need 
to specify these settings manually. However, note the following points.
-Check with your network administrator that the DHCP server is available.
If a DHCP server is not available, be sure to specify settings for “IP Ad-
dress”, “Subnet Mask”, and “Default Gateway”.
-If the IP address and other settings are assigned by the DHCP server, 
they may automatically be changed. If this happens, there is a possibility 
that the machine on the network can no longer be specified using the IP 
address. If “IP Address Setting Method” is set to “Auto Input”, it is rec-
ommended that the IP address assigned to the machine be fixed by con-
figuring the DHCP server.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-47
Specifying Settings From the Control Panel
Chapter 3
Items To Be Specified
The following items are specified.
TCP/IP Setting screen 1/5
TCP/IP Setting screen 2/5
TCP/IP Setting screen 3/5
TCP/IP Setting screen 4/5
ItemDescription
TCP/IP Setting Specify whether to turn on the TCP/IP settings.
ItemDescription
IP Address Setting Method Select whether to directly input a fixed IP address or to au-
tomatically acquire an IP address.
IP  Address Set the machine’s IP address. Use the keypad to type in the 
address.
Subnet Mask Set the subnet mask of the network to which the machine 
is to be connected. Use the keypad to type in the address.
Default Gateway Set the default gateway of the network to which the ma-
chine is to be connected.
ItemDescription
DNS Server Auto Obtain Select whether to automatically acquire the DNS server.
Priority DNS Server Set the primary DNS server address. Use the keypad to 
type in the address.
Substitute 1 DNS Server Set the substitute DNS server address. Use the keypad to 
type in the address.
Substitute 2 DNS Server Set the substitute DNS server address. Use the keypad to 
type in the address.
ItemDescription
DNS Domain Auto Obtain Select whether to automatically acquire the DNS domain 
name.
DNS  Default  Domain  Name Enter the DNS default domain name. Use the keyboard that 
appears in the touch panel to type in the name (up to 253 
characters).
DNS  Search  Domain  Name1-3 Enter the DNS search domain name. Use the keyboard that 
appears in the touch panel to type in the name (up to 253 
characters).
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-48 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
TCP/IP Setting screen 5/5
2
Note 
Be sure to enter the host name and domain name so that the total 
number of characters entered is within 254 characters.
To specify TCP/IP settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [2 TCP/IP Setting].
TCP/IP Setting screen 1/5 appears.
3Specify the desired settings.
4Touch [Fwd.→].
TCP/IP Setting screen 2/5 appears.
5Specify the desired settings.
ItemDescription
DynamicDNS Setting If the DNS server being used supports the dynamic DNS 
function, specify whether to enable a dynamic DNS.
Host Name Use the keyboard on the control panel to type in the host 
name of this machine.
IP Filtering Sets IP address filtering. For details on specifying the set-
ting, refer to “IP Filtering” on page 3-51.
RAW Port No. Specify the RAW port numbers for printing with a printer. 
For details on specifying the setting, refer to “RAW Port 
No.” on page 3-53.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-49
Specifying Settings From the Control Panel
Chapter 3
– If [Auto Input] was selected under “IP Address Setting Method”, 
specify the automatic acquisition procedure, and then touch [OK].
6Touch [Fwd.→].
TCP/IP Setting screen 3/5 appears.
7Specify the desired settings.
8Touch [Fwd.→].
TCP/IP Setting screen 4/5 appears.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-50 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
9Specify the desired settings.
10Touch [Fwd.→].
TCP/IP Setting screen 5/5 appears.
11Specify the desired settings.
12Touch [OK].
The TCP/IP settings are applied.
2
Note 
To cancel changes to the setting, touch [Cancel].
To quit specifying the Utility mode setting, touch [Exit] in the sub display 
area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode 
by touching [Close] in each screen until the screen for the Copy, Fax, 
Scan or Box mode appears.
2
Reminder 
In order to apply the changes made to [TCP/IP Setting] and [IP Address 
Setting Method], the machine must be turned off, then on again.
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-51
Specifying Settings From the Control Panel
Chapter 3
IP Filtering
The IP addresses in the specified ranges can be permitted or denied.
IP addresses can connect depending on whether “Enable” or “Disable” has 
been selected for “Permit Access” and “Deny Access” in the IP Filtering 
screen, as shown below.
1In TCP/IP Setting screen 5/5, touch [IP Filtering].
The IP Filtering > Permit Access screen appears.
2Touch [Enable] or [Disable] under “Permit Access”.
SettingIP AddressConnection Access
Permit Access
Disable
Deny Access
DisableAll IP addresses Connection possible
Permit Access
Enable
Deny Access
DisableIP addresses in the specified range Connection possible
IP addresses out of the specified range Connection not possible
Permit Access
Disable
Deny Access
EnableIP addresses in the specified range Connection not possible
IP addresses out of the specified range Connection possible
Permit Access
Enable
Deny Access
EnableIP address in the range allowed access and out 
of the range denied accessConnection possible
IP address in the range allowed access and in 
the range denied accessConnection not possible
IP address out of the range allowed access and 
out of the range denied accessConnection not possible
IP address out of the range allowed access and 
in the range denied accessConnection not possible
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-52 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
3Touch the button for a set (Set 1 to Set 5), and then use the keypad to 
type in the address range.
– The range setting cannot include “0.0.0.0”. For example, to specify 
all addresses before 192.168.1.20, specify the range from 0.0.0.1 to 
192.168.1.20.
– Touch [Deny Access] to specify the IP addresses to refuse access. 
The procedure for setting the IP addresses is the same as on the 
Permit Access screen.
– To edit the values that you entered, touch [←] or [→] to move the 
cursor to the desired area, touch [Delete], and enter the new value.
– To clear all values, press the [C] (clear) key.
4Touch [OK].
IP filtering is set.
2
Note 
To cancel changes to the setting, touch [Cancel].
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-53
Specifying Settings From the Control Panel
Chapter 3
RAW Port No.
Specify the RAW port numbers used by the printer. By specifying multiple 
port numbers, multiple data can be accepted simultaneously.
1In TCP/IP Setting screen 5/5, touch [RAW Port No.].
The RAW Port Number screen appears.
2Touch the button for the desired port.
3Touch [ON] or [OFF].
4To use the selected port, press the [C] (clear) key to erase the value, 
and then use the keypad to type in the RAW port number (between 1 
and 65535).
– If a value outside of the allowable range is specified, the message 
“Input Error” appears. Type in a value within the allowable range.
5Touch [OK].
The RAW port usage and RAW port numbers are set.
2
Note 
When using the RAW port, set [Spool Print Job in HDD before RIP] to 
[ON]. A timeout may occur if it is set to [OFF].
2
Note 
For details on the spool settings, refer to the User’s Guide for the IC-204.
Downloaded From ManualsPrinter.com Manuals 
						

							3Specifying Settings From the Control Panel
3-54 bizhub 500/420
Specifying Settings From the Control Panel
Chapter 3
3.13 NetWare Settings
The settings for using the machine on a NetWare network can be specified.
NetWare Parameters
The NetWare settings are as follows:
NetWare Setting screen 1/5
NetWare Setting screen 2/5
NetWare Setting screen 3/5
NetWare Setting screen 4/5
ItemDescription
IPX Setting Specify whether to use IPX.
Ethernet Frame Type Sets the frame type that is used for communications.
Authentication System When [ON (External Server)] was selected in “User 
Authentication”, specify whether to allow NDS 
authentication.
ItemDescription
NetWare Print Mode Select the print mode to be used.
Status The NetWare status can be verified. For details on specify-
ing the setting, refer to “Status” on page 3-58.
ItemDescription
Print Server Name Sets the print server name. Use the keyboard that appears 
in the touch panel to type in the print server name (up to 63 
characters).
Print Server Password Sets the password that is required when the print server 
logs in to the file server. Use the keyboard that appears in 
the touch panel to type in the password (up to 63 
characters).
Polling Interval Sets the interval for searching the print queue. To change 
the interval, press the [C] (clear) key, and then use the 
keypad to type in the value (between 1 and 65535).
NDS/Bindery Setting If bindery is disabled, only NDS is enabled. If bindery is 
enabled, both NDS and bindery are enabled.
ItemDescription
File Server Name Sets the file server name to which the print server logs in. 
Use the keyboard that appears in the touch panel to type in 
the server name (up to 47 characters).
Downloaded From ManualsPrinter.com Manuals 
						

							Specifying Settings From the Control Panel3
bizhub 500/420 3-55
Specifying Settings From the Control Panel
Chapter 3
NetWare Setting screen 5/5
To specify NetWare settings
1In the Administrator Setting screen, touch [5 Network Setting]. (Refer to 
page 3-8 for more details.)
2In the Network Setting screen, touch [3 NetWare Setting].
NetWare Setting screen 1/5 appears.
3Specify the desired settings.
4Touch [Fwd.→].
NetWare Setting screen 2/5 appears.
NDS Context Name Sets the NDS context name. Use the keyboard that 
appears in the touch panel to type in the NDS context name 
(up to 191 characters).
NDS Tree Name Sets the NDS tree name. Use the keyboard that appears in 
the touch panel to type in the NDS tree name (up to 63 
characters).
ItemDescription
ItemDescription
Print Server Name Sets the print server name. Use the keyboard that appears 
in the touch panel to type in the print server name (up to 63 
characters).
Printer  Number Sets the printer number. To change the value, press the [C] 
(clear) key, and then use the keypad to type in the value 
(between 0 and 254).
Downloaded From ManualsPrinter.com Manuals