Home > GTE > Communications System > GTE Omni Scbs Installation And Maintenance Manual

GTE Omni Scbs Installation And Maintenance Manual

Add to Favourites
    Download as PDF Print this page Share this page

    Have a look at the manual GTE Omni Scbs Installation And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 GTE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    View all the pages
    Page
    of 656
    Add page 501 to Favourites
    image text
    Enable zoom 
    							Data Switching Programming
~DE~CRIPTI~N~INTERNAL DATA COMMUNICATIONS CAN BE ACCOMMODATED FOR CSD TELEPHONES
EQUIPPED WITH A DATA ADAPTER (DTA) USING AN RS-232-C INTERFACE BETWEEN
THE CSD AND A CUSTOMER SUPPLIED DATA TERMINAL STATION.
CALLS CAN BE ESTABLISHED AS VOICE ONLY, DATA ONLY, OR SIMULTANEOUSVOICE/DATA.
SYSTEM PROVIDES ASYNCHRONOUS OR SYNCHRONOUS COMMUNICATION IN FULL
OR HALF DUPLEX MODES WITH SPEEDS OF UP TO 19,200 BPS. DATA TERMINAL
STATION ATTRIBUTES FOR BOTH THE SENDING AND RECEIVING TERMINALS MUST BEMADE COMPATIBLE WITHIN THE SYSTEM DATA BASE.
DATA TERMINAL STATIONS CAN BE PROGRAMMED TO INITIATE DATA CALLS IN AUTO
ORIGINATE OR MANUAL ORIGINATE MODE AND RECEIVE DATA CALLS IN AUTO
ANSWER OR MANUAL ANSWER MODE.
DATA CALLS CAN BE RELEASED USING EITHER NORMAL 
DICONNECT OR AUTOMATIC
DISCONNECT MODES.DATA TERMINAL STATIONS ARE ASSIGNED DATA TERMINAL STATION DIRECTORY
NUMBERS USING A FLEXIBLE NUMBERING PLAN SEPARATE FROM THE VOICE STATION
DIRECTORY NUMBERING PLAN.
OPTIONAL DATA FEATURES INCLUDE ASSIGNMENT TO CLASS OF SERVICE LEVELSFOR DATA TERMINAL STATIONS, ASSIGNMENT TO DATA TERMINAL STATION HUNT
GROUPS, OR ESTABLISHMENT OF DATA TERMINAL STATION HOT LINES.
DATA TERMINAL STATIONS CAN BE ASSIGNED TO TENANT AND METERING GROUPS.
4.50
    Add page 502 to Favourites
    image text
    Enable zoom 
    							tching Program
1 PROCEDURE 1
-I.INSTALL DATA ADAPTERS (DTA) IN CSD TELEPHONES TO BE CONNECTED TO DATA TERMINAL
STATIONS.
2.INSTALL CSD INSTRUMENTS. ENSURE THAT CSD INSTRUMENTS WITH DATA 8DTC CARDS
INSERTED IN SLOTS 
00,03,06,09 OR 12. CONNECT DATA TERMINALS STATIONS TO RS-232-C
INTERFACE IN REAR OF CSD TELEPHONES.
3.ASSIGN CSD TELEPHONES AS VOICE STATIONS AND DESIGNATE APPROPRIATE SERVICE USING
CMC-201,202,203, AND 204.
NOTE:REFER TO STUDENT WORKBOOK, DATA BASE ADMINISTRATION MODULE, FOR
DESCRIPTIONS AND PROCEDURES.
4.ASSIGN DATA TERMINAL STATION WITH CMC-220:. EQUIPMENT NUMBER 
(Pl)
DIRECTORY NUMBER OF DATA STATION (Pi)
CMC=220.PI:006 P4:206.
DATA INTERFACE TYPE (P3)
cl
P2:3648P3:l.
DIRECTORY NUMBER OF CORRESPONDING VOICE STATION (P4)
5.ASSIGN DATA TERMINAL STATION CLASS OF SERVICE/CLASS OF RESTRICTION LEVELS WITH
CMC-221:
@DIRECTORY NUMBER OF DATA STATION (Pl).
DAY CLASS OF SERVICE (P2) - (DEFAULT = 1)
@NIGHT CLASS OF SERVICE (P3) - (DEFAULT = 1)P1:3648 P4:l.
DAY CLASS OF RESTRICTION (P4) - (DEFAULT = 1).
NIGHT CLASS OF RESTRICTION (P5) - (DEFAULT = 1)
4.51
    Add page 503 to Favourites
    image text
    Enable zoom 
    							/ ’.  .!,,.. -1..\
6.ASSIGN OR MODIFY FAULT DATA TERMINAL STATION ATTRIBUTES WITH CMC-222:
0DIRECTORY NUMBER OF DATA TERMINAL STATION (Pl).DATA SPEED (P2) 
- (DEFAULT = 1200 BPS)CMC=222.SYNCHRONIZATION AND COMMUNICATIONS (P3) 
- (DEFAULT =P1:3648 P4:4ASYNCHRONOUS/FULL DUPLEX)P2:5P5:3.WORD STRUCTURE (P4) 
- (DEFAULT = STOP BIT-l BIT,)P3:3P6:O.PARITY (P5) (DEFAULT = SPACE)
cl.ECHOPLEX (P6) (DEFAULT = 
NO? USED)
I
CMC=223
P1:3648 P4:OP2:OlllP3:lll
1
7.ASSIGN RS-232-C INTERFACE SIGNAL MODE WITH CMC-223:
.DIRECTORY NUMBER OF DATA TERMINAL STATION 
(Pl)
@CALL CONTROL MODE (P2) - (DEFAULT = MANUAL ORIGINATE AND ANSWER MODES,
NORMAL DISCONNECT MODE, AND ONE RING
OPTION IN AUTO ANSWER NOT USED)
0RS-232-C INTERFACE SIGNAL/MODE 1 (P3) - (DEFAULT = DTR-NORMAL, RTS-NORMAL, AND DSR-NORMAL)
0RS-232-C INTERFACE SIGNAL/MODE 2 (P4) - (DEFAULT = Rl OPTION-STEADY ON)
8.ASSIGN DATA TERMINAL STATION OPERATION MODE, DIAL MODE, TENANT GROUP AND
METERING GROUP NUMBERS WITH CMC-224:
0DIRECTORY NUMBER OF DATA TERMINAL STATION (Pl)
oOPERATION MODE (P2) - DEFAULT = TWO-WAY)
0DIAL MODE (P3) - (DEFAULT = TELEPHONE DIAL)
0TENANT NUMBER (P4) - (DEFAULT = BLANK)
0METERING GROUP NUMBER (P5) - (DEFAULT = BLANK)
Data Switching Programming(Continued)
CMC=224P1:3648 P4:P2:lP5:
P3:O
I
9.IF DESIRED, ASSIGN DATA TERMINAL STATIONS TO DATA HUNT GROUPS WITH CMC-301:
0DATA TERMINAL STATION HUNT GROUP NUMBER (Pl)P1:51 P4:2
0 TERMINATING (P2)
EdDIRECTORY NUMBER OF DATA TERMINAL HUNT GROUP NUMBER (P3)
.HUNT GROUP TYPE (P4)
4.52
    Add page 504 to Favourites
    image text
    Enable zoom 
    							Data SwitchingProgramming
10.IF APPLICABLE, ASSIGN DATA TERMINAL STATIONS TO HOT LINE SERVICE WITHCMC-304:
.DATA HOT LINE NUMBER 
(Pl) - (51-90)
.ORIGINATING DATA TERMINAL STATION (P2)
.TERMINATING DATA TERMINAL STATION (P3)
NOTE:REFER TO STUDENT WORKBOOK, DATA BASE ADMINISTRATION MODULE FOR HUNT
GROUP AND HOT LINE SERVICE FEATURE DESCRIPTIONS.
4.53
    Add page 505 to Favourites
    image text
    Enable zoom 
    							Student Notes4.54
    Add page 506 to Favourites
    image text
    Enable zoom 
    							External Speaker Paging Assignment
[ DESCRIPTION 1
.
EXTERNAL PAGING IS ACCOMPLISHED BY UTILIZING CUSTOMER-SUPPLIED
SPEAKER/AMPLIFIERS.
@PAGING IS ACTIVATED BY DEPRESSING A FEATURE BUTTON OR DIALING AN ACCESS CODE AND
ZONE NUMBER..PAGING AMPLIFIERS ARE PROGRAMMED FOR A MAXIMUM OF 9 PAGING ZONES.
1.INSERT 4BWC CARD AND INSTALL EXTERNAL SPEAKER/AMPLIFIER WITH APPROPRIATE CROSS
CONNECTIONS (REFER TO PACKAGE B, INSTALLATION SECTION).
2.ASSIGN EQUIPMENT NUMBER AS EXTERNAL PAGING TRUNK CIRCUIT WITH CMC-250.. EQUIPMENT NUMBER (PI)
.
TYPE OF TRUNK (P2). TRUNK GROUP NUMBER (P3)
. OPERATION MODE (P4)
. SIGNALING (P5)
. ZONE NUMBER (P6),
CMC=250P1:182 P4:3
P2:9P5:lP3:3P6:l
4.55
    Add page 507 to Favourites
    image text
    Enable zoom 
    							/“““\.‘: -‘-\.,,;-7: .,.
External Speaker Paging Assignment
GUE OMNU SBCS
3.IF APPLICABLE, CHANGE FEATURE ACCESS CODES FOR EXTERNAL PAGE ACCESS AND ENTERWITH 
CMC-lOO:-. FEATURE NUMBER 
(Pl).
FEATURE ACCESS CODE (P2)
CMC=lOOP1:51p2:**
I
4.IF APPLICABLE, CHANGE EXTERNAL PAGING WARNING BURST TIMING WITH
CMC-103:.IDENTIFICATION FOR TIMING (PI)
l MULTIPLIER (P2)
CMC=lO3
P1:45P2:l
4.56
    Add page 508 to Favourites
    image text
    Enable zoom 
    							Message Waiting for SLT Programming
.PACKAGE B ACCOMMODATES THE MESSAGE WAITING LAMP FEATURE FOR SLT
INSTRUMENTS USING SYSTEM ACCESS CODE..
FEATURE FIRST MUST BE ACTIVATED ON SYSTEM AND THEN ASSIGNED TO SLT
INSTRUMENTS ON AN INDIVIDUAL BASIS.
piiiiq
1.ACTIVATE MESSAGE WAITING FOR SLT INSTRUMENTS WITH CMC-102:CMC=lO2. FLAG NUMBER (PI)
. SET VALUE (P2)
c-
P1:15P2:l
2.ASSIGN MESSAGE WAITING FEATURE TO INDIVIDUAL SLT INSTRUMENTS EQUIPPED
WITH LAMP USING CMC-204:
CMC=204.
SLT WITH MESSAGE WAITING LAMP IDENTIFICATION (P4)c
;:I. STATION DIRECTORY NUMBER 
(Pl)P1:218 P4:l
4.57
    Add page 509 to Favourites
    image text
    Enable zoom 
    							DEFAULT ACCESS CODES FOR THE FOLLOWING PACKAGE 6 FEATURES CAN BE
MODIFIED IF DESIRED:
EKT PAGING ANSWER (FNO 52, ACCESS CODE = 87)EXTERNAL PAGING ACCESS (FNO 53, ACCESS CODE = 78)
EXTERNAL PAGING ANSWER (FNO 54, ACCESS CODE = 88)
DATA CALL ATTRIBUTE CHANGE (FNO 117, ACCESS CODE = 69)
ADD DATA CALL (FNO 160, ACCESS CODE = 67)
lPROCEDUREj
1.CHANGE FEATURE ACCESS CODE NUMBERS WITH CMC-100:
l FEATURE NUMBER (PI)
.FEATURE ACCESS CODE (P2)
NOTE: P3
- P6 ARE NOT APPLICABLE FOR THESE FEATURES.
4.58
    Add page 510 to Favourites
    image text
    Enable zoom 
    							System Parameters/Package B] DESCRIPTION 1
QPACKAGE B MAY REQUIRE MODIFICATION OF SETTINGS FOR FOLLOWING
APPLICABLE SYSTEM PARAMETER FLAGS:.POUND CODE TREATMENT FOR TIE OR CO TRUNKS (FLAG NUMBERS 13 AND 14)
0ACTIVATION OF MESSAGE WAITING FOR SLT INSTRUMENTS (FLAG NUMBER 15)
0NUMBER OF DIGITS TO BE SENT AS ACCOUNT CODES FOR SYSTEM
SPECIALIZED COMMON CARRIERS (FLAG NUMBERS 16 
- 21).
(PROCEDURE1
1.CHANGE SYSTEM PARAMETER FLAGS WITH CMC-102:
0 FLAG NUMBER (PI)
0 SET VALUE (P2)
4.59
    All GTE manuals Comments (0)

    Related Manuals for GTE Omni Scbs Installation And Maintenance Manual