GTE Omni Scbs Installation And Maintenance Manual
Have a look at the manual GTE Omni Scbs Installation And Maintenance Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 GTE manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
4.2 Enling Objective GlVEN:0 @ 0 0 0 ACTION:0 e 0 0 0 0 CRITERIA:0 0 GTE OMNI SBCS (PREVIOUSLY INSTALLED) GTE OMNI SBCS PACKAGE B EQUIPMENT AND PERIPHERALS -CPMB, MEMB, 8DTC, AND RGEN CARDS - CSD TELEPHONES - @SD DATA ADAPTERS (DTA) - DATA TERMINALS/WORK STATIONS - EXTERNAL PAGING AMPLIFIER GTE OMNI SBCS COURSE AND SITE DOCUMENTATION PACKAGE STANDARD INSTALLATION TOOLS REVIEW EXERCISE INSERT AND SEAT PACKAGE B CARDS AND ACTIVATE STRAPPINGOPTION ON RGEN CARD FOR MESSAGE WAITING FEATURE ON SLT INSTRUMENTS. INSTALL DATA ADAPTER IN CSD TELEPHONES. INSTALL CSD TELEPHONE AND WIRE CROSS CONNECTIONS. CONNECT DATA TERMINALS TO CSD TELEPHONES. INSTALL EXTERNAL PAGING AMPLIFIER AND WIRE CROSS CONNECTIONS. COMPLETE REVIEW EXERCISE. ENHANCED CARDS AND NEW PERIPHERALS WILL BE INSTALLED IN ACCORDANCE WITH STUDENT WORKBOOK AND GTE OMNI SBCS GTEP MANUAL. REVIEW EXERCISE QUESTIONS WILL BE COMPLETED CORRECTLY INACCORDANCE WITH PASS/FAIL CRITERIA OF THIS TRAINING ORGANIZATION. 4.31
Package B Card Installation POWERSUPPLY 1. 2.GROUND YOURSELF PRIOR TO HANDLING CARDS. SINCE SYSTEM POWER MUST BE TURNED OFF WHEN INSTALLING OR REPLACING CPMC OR MEMC CARDS, OFFICE DEPENDENT DATA BASE WILL BE DELETED AND CUSTOMIZED DATA BASE MUST BE REPROGRAMMED. 3.IF MESSAGE WAITING ON SLT INSTRUMENTS IS REQUIRED, CUT STRAP OR SLIDE SWITCH ON RGEN CARD. 4.INSTALL CARDS AFFECTED BY PACKAGE B IN DESIGNATED SLOTS: RGEN - RGEN SLOT 8DTC - SLOTS 00 THROUGH 14 (IF DTA IS INSTALLED, USE SLOTS 00,03,06,09, OR 12) CPMB - SLOT 20 MEMB - SLOT 21 5.INITIALIZE CARDS BY COLD RESTARTING SYSTEM. PRESS RESTART BUTTON WITH TOGGLE IN UPPER POSITION ON CPMB CARD. 6.REPROGRAM THE SYSTEM IF CPMB, MEMB, OR RGEN CARDS HAVE BEEN REPLACED. 4.32
Data Terminal Adapter (DTA) InstallationMASKINGPLATE 1 PROCEDURE1.INSTALLATION OF DATA ADAPTER (DTA) IN CSD TELEPHONE ALLOWS RS-232-C INTERFACE CONNECTION TO A CUSTOMER-SUPPLIED TERMINAL OR WORK STATION. aREFER TO FOLLOWING PAGE FOR DTA INSTALLATION PROCEDURE. 4.33
-- .Data Adapter (DTA) Installation 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.ENSURE THAT YOU ARE WEARING A GROUNDED ANTI-STATIC WRIST STRAP. REMOVE THE DTA, AC POWER SUPPLY ADAPTER, TWO GROUNDING WIRES, FIVE WASHERS, AND THREE SCREWS FROM PACKAGE. REMOVE UPPER CASE AND MASKING PLATE FROM CSD TELEPHONE. INSTALL TWO GROUNDING WIRES TO CSD CONTROL CIRCUIT CARD. GROUNDING WIRE A IS TWO INCHES IN LENGTH AND WIRE B IS EIGHT AND FIVE-EIGHTHS INCHES IN LENGTH. ATTACH WIRES WITH ONE WASHER AND SCREW, IN FOLLOWING SEQUENCE: WASHER, WIRE, AND SCREW. PLACE THE DTA ON THE BOSSES, THEN CONNECT THE TWO GROUNDING WIRES TO THE DTA WITH THE TWO WASHERS AND SCREWS USED TO FASTEN THE DTA TO THE BOSSES.INSTALL THE THIRD WASHER AND SCREW USED TO FASTEN THE DTA TO THE BOSSES.CONNECT THE CONNECTOR FROM THE DTA TO THE CONNECTOR ON THE CONTROL CIRCUIT CARD. REPLACE THE CSD TELEPHONE’S UPPER CASE.PLUG THE POWER ADAPTER CORD INTO THE AC POWER JACK ON THE REAR OF THE CSD TELEPHONE. PLUG THE AC POWER SUPPLY ADAPTER INTO AN AC POWER OUTLET. PROCEED WITH CSD TELEPHONE INSTALLATION AND CROSS CONNECTION. 4.34
@DIAGRAM REPRESENTS A TYPICAL EXAMPLE OF CROSS CONNECTIONS FOR A CSD TELEPHONE. eEACH CSD TELEPHONE REQUIRES ONLY ONE PAIR OF WIRES FOR TIP AND RING (SIMILAR TO SLT CROSS CONNECTIONS). ON THE CDF TERMlNAL BLOCK, ONLY EVERY OTHER PAIR OF WIRES IS USED. 8EXAMPLE ILLUSTRATES CDF CROSS CONNECTION FOR AN 8DTC INTERFACE CARD IN SLOT 00, USING CABLE NUMBER (CN) 0. CONNECTOR BLOCK SHOWN WOULD HANDLE ALL EIGHT CIRCUITS FOR THE CARD SLOT IDENTIFIED ABOVE. .REFER TO CDF CROSS CONNECT REFERENCE CHART IN OF STUDENT WORKBOOK, INSTALLATION MODULE FOR CROSS CONNECTION INSTRUCTIONS FOR OTHER CARD AND EQUIPMENT CONFIGURATIONS.25 PAIR CDF BLOCK TIP \ RING GREEN 11RED 1 MODULAR CABLE 25 PAIR CABLEI TYPICAL CSD CROSS CONNECTION
Data Terminal Installation POWER CORD *REQUIRES FOLLOWING PIECES OF EQUIPMENT: - - -CUSTOMER SUPPLIED DATA TERMINAL, WORK STATION, OR PRINTER @SD TELEPl-lONE WITH INSTALLED DATA TERMINAL ADAPTER (DTA) AC POWER SUPPLY ADAPTER CSD TO DATA TERMINAL CABLE 4.37
Data Terminal Installation (Continued) lDESCRlPTlONl (Continued) @DATA TERMINAL’S RS-232-C PORT PIN CONFlGURATlON MUST BE COMPATIBLE WITH PIN CONFIGURATION FOR RS-232-C PORT ON CSD TELEPHONE’S DATA TERMINAL ADAPTER (DTA), AS LISTED BELOW: 0PIN CONFIGURATION 12 3 4 5 6 7 a 9 10 11 12 13 14 15 16 17 18 19 20 21 22 2324 25SIGNALDESCRIPTION FGTD RDRTS CTS DSR SG RLSDST2TRANSMISSION SIGNAL ELEMENT TIMING DTRDATA TERMINAL READY RIRING INDICATOR PROTECTIVE GROUND TRANSMITTED DATA RECEIVED DATA REQUEST TO SEND CLEAR TO SEND DATA SET READY SIGNAL GROUND (COMMON GROUND) RECEIVED LINE SIGNAL DETECTOR 4.38
Data Terminal Installation (Continued) IPR~CEDUREICONNECTOR 1.ENSURE THAT DTA IS INSTALLED IN CSD TELEPHONE.TELEPHONE CORD 2.PLUG DATA TERMINAL POWER CABLE INTO THE POWER OUTLET.POWER OUTLET 3.CONNECT CSD AND DATA TERMINAL WITH THE CSD TO DATA TERMINAL CABLE. 4.39